Directorate Of Municipal Administration Tender

PWD SR Vol-I, I.No. 2.5.1 P.No.16 - Providing and laying in position Cement Concrete for all Sub structures ofbuilding, Irrigation works, Sub structure works of bridges, Drain works &other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compactedusing needle vibrators, providing weep holes wherever necessary, includingall lead & lifts, cost of all materials of quality, confirming to the requirementsof relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M30 Design Mix Using 20 mm nominal size graded crushed coarse aggregates

PWD SR vol.1 Item no 2.11(a) page no-18 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcementincluding cost of all materials, machinery, labour, cleaning, straightening,cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification.

PWD SR vol.2 tem no 8.1.2 page 412 - Providing 12 mm cement plaster with cement mortar 1:6 (1 cement:6 fine sand) including rounding off corners wherever required smoothrendering, providing and removing scaffolding, including cost of materials,labour, curing complete as per specifications and as per directions ofEngineer-in-charge

PWD SR vo.2 Item no8.8 page-42 - Providing 18 mm cement plaster in two coats under layer 12 mm thickcement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finishedwith a top layer 6 mm thick cement plaster with cement mortar 1:6 (1cement : 6 fine sand) to brick masonry including rounding off cornerswherever required smooth rendering, providing and removing scaffolding,including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge

PWD SR vol.2 Item no 8.33.1 page no-46 - Finishing with Deluxe Multi surface paint system for interiors and exteriorsusing Primer as per manufacturers specifications: Two coats applied onwalls @ 1.25 L/10 m² over and including one coat of Special primer applied@ 0.75 L/10 m² with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (The gloss should be 50% @ 60 degree angle with 10 years life)

PWD SR vol.2 Item no 9.17.2 page no-61 - Providing and laying Vitrified tiles with thickness 9-10 mm in differentsizes with water absorption less than 0.08 % and conforming to I.S. 15622,of approved make, in all colours & shade, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joint with white cement & matching pigments etc. complete

PWD SR, vol-2 Item no 13.34 page no-123 - Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

PWD SR, vol-5 Item no 13.34 page no-21.1.9 - Water purification plants: Providing, Installation and Commissioning of automatic Water purification plant (RO+UF) with all accessories piping, product water tank on single phase power supply as per the enclosed detailed Technical Specifications including cost of material, loading and unloading and as directed by the Engineer in charge. (Ref- detailed specification enclosed seperatly). Note:- 1.The above rates mentioned are only for the preparation of estimate purpose. 2. All items are to be of BSI /NFS standards, with BSI / NFS mark . 3. Tenders to be invited for procurement. 4. No direct payment should be made under any situation or condition or on any account. 5. After commissioning of plant necessary testing to be done for the satisfactory of Engineer Incharge. Note : Refer the ANNEXURE : F for Detailed Specification of Each componen 1000 LPH SS : Skid Type Each 441000 21.1.10 For 1000

page no-15, Item.no-14.10 - Providing &,fabrrcation & construction of upvc Lift and shif porta Cabins made out of M.S. 100 mm C Section for base with middle, vertical and for roof supports welded with 50 X50 and 40mmX2Omm M.S. tubes and angles for structure. uPVC panels 10 X 15S X 1.2 mm and 355 X120X 1.2mm extruded sections fixed on both side by hidden Screwing system with upVC false ceiling. Door Frame made out of uPVC extruded profiles with accessories etc comp]ete, of size 1.00x2.10 and 2.40x2.10 mtr, Windows 2 no.s of size 0.90x1.00 mtr made out of UPVC extruded profiles with 5 mm plain Glass shutters, as per approved specifacations, the Ceiling clear height of 2.85 and 2.75 mtr,Roofing of Pre-coated G.l. sheet of standard make of 0.45mm thick and suitable Lifting arrangements will be provided to porta Cabins with a partition for ATM chamber. Over all Size 6,06 m x 3.06 m including cost of material, labour, loading,unloading, erection at various sites as per the directions of the engineer in charge .

page no-15, Item no-14.51 - Supply of Stainless steel water Storage tank 1000 litres SS 304 grade as per BIS Standards including transportation, Installation & commissioning, Electrical & Plumbing, all taxes as applicable, etc complete work as per direction of Engineer in charge of work

page no-14, Item no-15.41 - supply of coin wending machine with motor & flow sensor as per BIS Standards including transportation, Installation & commissioning, Electrical & Plumbing, all taxes as applicable, etc complete work as per direction of Engineer in charge of work

page No.2 Item No. 1.1.2 - Supplying heavy gauge PVC conduit pipe …….dia .mm thick confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in case of RCC ceiling and RCC wall / stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws.

I.no.3.4.4, page no-02 - Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.C wall, including necessary rawl plugs, Machine/NF screws etc., complete.

page no-2, item no-2.1.1 - Point wiring using Copper wire with switch. Supplying and wiring adopting loop system in existing PVC Conduit / casing capping using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated, 2 X1.5Sq.mm Cable confirming to the GTP, with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet.

page no-03-, item no-3.4 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand Copper with low conductor resistance single core wire in open or concealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP -A

I.No.3.3.B.6. page no-03 - 32Amps Flush/projected type DP switch.

p.no.44 i.no.6.7.3 - Supplying and fixing of 16Amps Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers etc., complete

p.no.47 i.no.6.16.1 - Supplying and fixing miniature circuit Breaker (MCB) on the existing MCB distribution board using necessary fixing materials, and C type curve, indicator ON/OFF energy cross-3 with short circuit breading capacity of 10K and complete wiring as required confirming to IEC 60898

p.no.55 i.no.7.1 - Supplying, fixing, wiring, earth electrode for grounding conduitgs, IC cutouts and other equipments on the meter board using 40mm dia 2.90 thick GI pipe 2.5 mtr long burried in a pit The pit should be filled with equal proportion of salt and charcoal 150mm alround the pipe to complete depth. The connection from th pipe to the conduit etc, is to be established through -GI wire of size as per ISI specificaion 7.3.3 of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc., the pipe shall have 16through holes of 122 mm dia

I.No.4.10.1, PAGE NO-55 - Supply of Horizontal type Street light fluorescent fitting suitable for single/twin lamp of 24W/28W FTL T5 lamp. Housing shall be with pressure die cast aluminum with UV Protected clear acrylic diffuser with thermoformed & CRCA gear tray, push fit poly carbonate lamp holder, low loss high frequency electronic ballast with IP 54 protection

pipe.p.no.28i.no.2(b) - Supplying and fixing . Mm dia class A GI pipe bracket up to 2.7 meters long terminated with a reducing collar of 40*25 mm to which extra pipe of 175mm length is fixed for fixing MV/SV/MH/FTL street light fitting of all capacities on rail/RCC/wall/tubular pole, using suitable clamps, bolts, nuts and wiring using suitable capacity wires etc complete. (b) using 32mm dia G.I

Market rate - Hescom Deposit etc.