Directorate Of Municipal Administration Tender

8.42.3 - Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of PCC shall be paid extra) 600 x 300 x 150 mm size. vol 3 page 74 item 8.42.3

6.8.2 - Providing and laying 80mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Commercial Traffic Axle load repetitions upto 10MSA & for Residential Streets of approved shape and colour, laid in required pattern and including over 40mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (WMM/WBM Base to be paid separately as per relevant technical specification) vol 3 Page No 51 Item No 6.8.2

2.1.4 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 Using 20 mm nominal size graded crushed coarse aggregates. vol 1 Page No 15 Item No 2.1.4

8.4 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.vol 2 Page No 48 Item No 8.4

SE approved rate - Providing, Supplying, fixing & installation of Cross Walker:Made up of All tubular steel of 2.5MM thickness are galvanized and zinc dipped. Joints are Robotic welded. All welded jolints are scalloped as necessary and welded to an approved MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the-welding pointsto dinishing. All metal parts are powder coated using AKZO nobel-Great Wall powder the thickness of 80- microns. All metal parts are tested Ino uses a 5% NaCl solution in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Malntenance free ball bearings. Scope of Delivery: . 1 completely pre-assembled equipment modules. Maintenance: Maintain according to EN 16630 and the maintenance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS or equivalent. The GS Mark EN15630 Cetificates must be in the name of Company manufacturing the equipment. All products must clearly display the GS Mark as has been issued in the EN 16630 safety certificates. SizeLxWxH: 2015 x 615 x 1350 mm or nearly equivalent to it, Weight: 93 KG Safety Area: 5015 x 3015 mm,Capacity 2 Persons.Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant iincidentail works.

SE Approved rate - Providing, Supplying,fixing & installation of Leg & Thigh Exercise/Air Walker: Made up of All tubular steel of 2.5MM thickness are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an apprvoed MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to dinishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are tested in our salt spray machine that uses a 5% NaCl solution in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free bal bearings. Scope of Delivery: 1 completely pre-assembled equipment modules. Maintenance: Maintain according to EN 16630 and the maintenance guide. Safety All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS or equivalent. The GS Mark EN16630 Cetificates must be in the name of Company manufacturing the equipment. All products must clearly display the GS Mark as has been issued in the EN 16630 safety certificates. SizeLxwxH: 1065 x 615 x 1364 mm or nearly equivalent to it, Weight: 51 KG Safety Area: 4090 x 3555 mm, Capacity 1 Person. Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant iincidentail works.

SE Approved rate - Providing, Supplying, fixing & installation of Tai Chi Wheel :Made up of All tubular steel of 2-5mm thickness are galvanized ans zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to diminishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are tested in our salt spray machine that uses a 5% NaCl solution in accordance to IS07227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre-assembled equipment modules. Maintenance: Maintain according to EN 16630 and the maintenance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA TUV, CPSC or SGS or equivalent. The GS Mark EN15630 Cetificates must be in the name of Company manufacturing the equipment. AlI products must clearly display the Gs Mark as has been issued in the EN 16530 safety certificates. SizeLx Wx H: 1120x 1150 1620mm or nearly equivalent to it, Weight 3520 x 3550mm, Capacity 3 Persons.Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant incidental works.

SE Approved rate - Providing, Supplying,fixing & installation of single pole step up cycle : Made up of All tubular Steel of 2.5mm thickness are gravanized and zinc dipped. Joints are robotic welded All welded joint are scalloped as necessary and welded to an approved MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to dinishing. All metal parts are power coated using AKZO nobel-Great Wall power to the thickness of 80-120 microns. All metal parts are tested in our salt apray machine that uses a 5% NaCl solution in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber : High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearing. Scope of Delivery: 1 completely pre-assembled equipment models. Maintnance: Maintain according to EN 16630 and the maintnance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificate must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS or equivalent. The GS mark EN16630 Certificates must be in the name of Company manufacturing the equipment . All products must clearly display the GS mark as has been Issued in the EN 16630 safety certificates. All products must carry a GS mark on it. Size:1000X498X1290mm or nearly equivalent to it, Weight: 51.5 KG, Safety Area: 3400 x 3498 mm, Capacity 1person. Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant incidental works.

SE Approved rate - Providing, Supplying,fixing & installation of Seated Chest press Metal: Made up of All tubular steel of 2.5MM thickness are glavanized and zinc dipped. Joint are Robotic welded. All welded jointS are scalloped as necessary and welded to an approved MIG Process. All welds are dressed off removing all shap edges and burrs. zinc primer paint is applied at all the welding points prior to dinishing. All metal parts are powder coated using AKZO nobel grate wall powder to the thickness of 80-120 micrones. All metal parts are tested in our salt spray machine that uses a 5% NaCl soultion in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearing: Maintenance free ball bearing. Scope of Delivery; 1 completely pre-assembled equipment modules. maintnance Maintain according to EN 16630 and the Maintnance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificate must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS or equivalent. The GS mark EN16630 Certificates must be in the name of name of Company manufacturing the equipment . All products must clearly display the GS mark as has been Issued in the EN 16630 safety certificates. All products must carry a GS mark on it. SizeL x W x h: 1955 x 733 x 2058mm or nearly equivalent to it, weight:86.6 KG, Safety Area: 5545 x 4470mm, capacity 2 person. Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant incidental works.

SE approved rate - AB Trainer /sit-up Bench Providing, Supplying,fixing & installation of Sit Up Station Metal: Made up of All tubular steel of2.5MM thickness are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an apprvoed MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to dinishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns All metal parts are tested in our salt spray machine that uses 5% of NaCl solution in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the hadles.Bearings: Maintenance free ball bearlngs. Scope of Delvery: 1completely pre-assembled equipment modules. Maintenance Maintain according to EN 16630 and the maintenance guide. SafetyAll products must be tested ans certified to meet EN16630 safetystandards with GS test mark.( The EN, 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUv, CPSC or SGS or equivalent.The GS Mark EN16630 Cetificatesmust be in the name of name of Company manufacturing the equipment. All products must clearly display the GS Mark as has been issued in the EN 16630 safety certificates. SizeLxWxH: 1412 x 1366 x 650 mm or nearly equivalent to it, Weight: 42.6 KG Safety Area: 4462 x 4078 mm, Capacity 2.Persons. Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant iincidentail works.

SE approved rate - Providing, Supplying,fixing & installation of Leg press: Made up of All tubular steel of Each 0- 2.5MM thickness are glavanized and zinc- dipped Joints are Robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG Process. All welds are dressed off removing all sharp edges and burrs, Zinc Primer paint is applied at all the welding points prior to dinishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns all metal parts are tested in our salt spray machine that uses 5% NaCl solution in accoradance to IS07227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles Bearings: Maintenance free ball bearings. Scope of Delivery:1 completely pre-assembled equipment modules. Maintenance: Maintaln according to EN 16630 and the malntenance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with G S test marks. he EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS or equivalent. The G S Mark EN16630 Cetificates must be in the name of Company manufacturing the equipment. All products must be clearly display the GS Mark as has been issued in the EN 16630 safety certificates. SizeLxWxH; 2270 x 635 x 1640 mm or nearly equivalent to it, Weight: 60.2 KG Safety Area: 5300 x 3685mm, Capacity 2 Persons. Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant iincidentail works

SE approved rate - Supply & Fixing of Push and Pull up chair: Made up of All tubular steel of 2.5MM thickness are galvanized and zinc dipped. Joints are robotic welded. All welded joints are scalloped as necessary and welded to an apprvoed MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer paint is applied at all the welding points prior to dinishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are tested in our salt spray machine that uses a 5% NaCI solution in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free bali bearings. Scope of Delivery: 1 completely pre-assembled equipment modules. Maintain according to EN 16630 and the maintenance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified intermaltional certifying agency such as IPEMA TUV, CPSC or SGS or equivalent. The GS Mark EN15630 Cetificates must be in the name of Company manufacturing the equipment. All products must clearly display the GS Mark as has been issued in the EN 16630 safety certificates. SizeLxwxH: 2570, x 805 x 2685 mm or nearly equivalent to it, Weight: 85.4KG Safety Area: 5287x4848 mm, Capacity 2 Persons. Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant iincidentail works.

SE approved rate - Supply & Fixing of Waist Twister Triple: Made up of All tubular steel of 2.5MM thickness are glavanized and zinc dipped. Joints are Robotic welded. All welded joints are scalloped as hecessary and welded to an apprvoed MIG Process. All welds are dressed off removing all sharp edges and burrs. Zinc Primer palnt is appllied at all the welding points prior to dinishing. All metal parts are powder coated using AKZO nobel-Great Wall powder to the thickness of 80-120 microns. All metal parts are tested In our salt spray machine that uses a 5% NaCl solution in accordance to ISO7227 to speed up corrosion for 3000 Hrs. Rubber: High quality grip rubber is used for the handles. Bearings: Maintenance free ball bearings. Scope of Delivery: 1 completely pre assembled equlpment modules. Maintenance: Maintain according to EN 16630 and the maintenance guide. Safety: All products must be tested ans certified to meet EN16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified internaltional certifying agency such as IPEMA, TUV, CPSC or SGS or equivalent. The GS Mark EN16630 Cetificates must be in the name of Company manufacturing the equipment. All products must clearly display the GS Mark as has been Issued in the EN 16630 safety certificates. SlzeLxWxH: 1460 x 1310 x 1150 mm or nearly equivalent to it, Weight: 39.1 KG Safety Area: 4360 x 4510 mm, Capacity 3 Persons.Includes the cost of all labour charges, transportation, HOM of machinaries all complete in all respects with all applicant iincidentail works.