Directorate Of Municipal Administration Tender

code04 - HDPE Grade PE100-PN6.0,110mm dia HDPE Pipe 9.10.4

code05 - PE-100 (PN 6 KG/cm 2 )160 mm dia HDPE Pipe 9.10.7

code06 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m, and lift upto 1.5 m. Including cost of all labour complete as per specifications (Common SOR 2023-24, Volume-I , Page no:07, SL No:1.10 ).

code07 - CEMENT CONCRETE ROAD RESTORATION : Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383:2016:, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant, curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. KPWD SR 2023-24 VOL-III I NO 16.28 P No 149

code08 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complet (COMMON SCHEDULE OF RATES- 2023-24, Volume - V, Page NO:73, SL no: 2.23) For Suilce Valve of PN10.0 and 150mm

code09 - For Suilce Valve of PN - 10.0 and 100mm

code10 - For Suilce Valve of PN - 10.0 and 80mm

code11 - Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15 cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc, Volume -V Page No 107 9.17 100 MM Coupler

code12 - 150 MM Coupler

code13 - 100 ID TEE - fitting for 100mm dia pipes

code14 - 150 ID TEE - fitting for 150mm dia pipes

code15 - 150 ID TEE - fitting for 150mm dia pipes

code16 - 100 ID BEND - fitting for 100mm dia pipes

code17 - 150 ID BEND - fitting for 150mm dia pipes

code18 - 75 MM ELECTRO FUSION COUPLER

code19 - 75 MM ELECTRO FUSION TEE

code20 - 75 MM ELECTRO FUSION Elbow

code21 - Providing & fixing electro fusion saddle comply with BS EN12201 -3:2011, PN-12.5 rating and food grade raw material as per BS 6920 with material of construction PE 80 or PE 100 and colour of fitting - Blue/Black for water applications, EF tapping saddle is V-Regarding type. Designed to fuse at a fusion voltage of 40 volt AC. EF tapping saddle shall have moulded SS/Brass metal female threaded outlet. EF tapping saddle is fused by using a top loading piller type pressure exerting 1500N (150 kg apprx.) top load on EF saddle. Fusion time is 170 secs and cooling time is 10mins, Exerted pressure shoud be removed after completing the 10 mins cooling time. 63x20,75x20,90x20,110x20,140x20 etc. complete Volume V Page No 110 2023-24