Directorate Of Municipal Administration Tender

ele04 - Supply, erection, testing and commissioning of electrical motor driven end suction back pull out centrifugal pump capable of delivering,adequate LPM at required head. when running at 2900 rpm directly coupled to TEFC electrical motor of adequate HP to operate on 400/440 V 3 phase, 50 cycles AC supply with required foundation for pump, a terminal box suitable for reception, common bed plate with necessary anti vibration pads, necessary foundation bolts and accessories,neoprine gaskets (16 kg/sq.cm) Control panel is excluded. Required GA drawingfor the pump/foundation shall be submitted by the contractor.1620 lpm at 70m head, Item no 15.83.1 page no 29 vol6 CSR 2023-24

ele05 - Supply, installation, testing and commissioning of diesel engine driven pump, horizontal mounted, Horizontal spiltcase centrifugal single stage pump, capable of delivering required flow at required head when running at 1800 RPM with adequate BHP automatic diesel engine driven pumpset having the residential silencer system and other accessories like fuel tank, necessary radiator cooling system, flanges, neoprene gaskets (16.0 kg/sqcm), 200 litres fuel storage tank with piping, valves as per detailed specification and two separate starting mechanisms (automatic starting by battery power, electric starting motor as well as manual startingby electric start motor) common bed plate with anti vibration pads, 1620 lpm at 70m head, Item no 15.84.2 page no 29 vol6 CSR 2023-24

ele06 - Supply, Installation, testing and commisioning electrically driven jockey pump of capacity 180.0 Lpm at required head end suction type bronze impeller pump oupled to electrical driven motor with suitable HP with allthe necessary accessories, operating on 3Ph 50Hz, 400/440 V AC supplyincluding foundation, foundation bolts, anti vibration pad,etc. complete.Including cost of materials, labour, usage charges of machinery completeas per specifications. Control panle is excluded. Required GA drawingforthe pump/ foundation shall be submitted by the contractor. 180 lpm at 90m head, Item no 15.85.3 page no 30 vol6 CSR 2023-24

ele07 - Supply, erection, testing and commissioning of Fire Fighting panel cubicle type made out of 14/16 Swg MS CRCA sheet which is derusted, degreased, phosphated and passivated with angle iron skeleton or sheet folded construction. The panel to be dust and vermin proof type and with powder coated paint after suitable seven tank pretreatment. The panel will have individual compartments for incoming and outgoing feeders made out of cold rolled sheet and doors fitted with Neoprene gaskets and fasteners. The switchboards are to be tested as per IS 8623-1977 specifications. Busbars are to be of high conductivity Aluminium Alloy E91E IS 5082 specification. The panel shall have both bottom and top cable entry provisions and panel shall be mounted on Pedestal of 300 mm height. Incoming feeder for 320A TPN MCCB with 320 Amps. TPN Al. Bus bars with color coded heat shrinkable PVC sleeves, RYB indicating lamps with individual MCB control. Suitable Mulit Fuction meter with CTs OUTGOING Feeder for 1 No. of main pumps - 1 Nos.200A TP MCCB with 75 HP Star delta starter with over load relay, single phase preventer and indicating lamps with ON / OFF push buttons. 1 No. Auto manual selector switch.Feeder for 1 No. of Jockey pump - 1 No. 63A TP MCCB with 12.5 HP star delta starter with over load relay, single phase preventer and indicating lamps with ON / OFF push buttons. 1 No. Auto manual selector switch. Feeder for 1 No. DIESEL ENGINE MAIN PUMP - a) 20Amps DP MCB - 4 Nos. b) Battery charger with transformer with rectifier resistance DC ammeter, DC voltmeter, Trickle / booster / off selector switch - 2 Nos. c) 1 set of indicating lamps for the following - 1. phase indication 2. battery charger on 3. over load relay 4. DC supply on 5. control switch on 6. Engine fails to start 7. Pump on 8. Low oil pressure 9. High water temperature 10. Auto manual selector switch d) 1 sets of push button stations for the following - 1. Engine Start 2. Engine Stop 3. Engine - hooter ACK 4. Engine - fault reset e) Selector switches (Engine control, mode selector)-1 No. f) Auxiliary relays / contactors / timer for sequence operating for starting and stopping of the engine - 1 set. g) Hooter for audio alarm (Industrial type) - 1 No.Item no 15.140 page no 39 vol6 CSR 2023-24

ele08 - Supplying of four bucket stand alongwith buckets. Complete Item no 15.111 page no 34 vol6 CSR 2023-24

ele09 - FIRE HYDRANT SYSTEM Supplying Installing, testing and commissioning of 63mm mm dia single headed Gun mental Hydrant Valve with flanged inlet, stop valve, spindle and cast iron hand wheel. It has a female instantaneous outlet with Blank Cap and is Hydrostatically tested to 21 Kgf/cm2 pressure having a flow rate of 900 LPM at 7 Kgf/cm 2 of pressure with blank cap and wheel as per IS 5290 etc. complete including cost of materials, labour, usage charges of machinery complete as per specifications. Item no 15.86 page no 30 vol6 CSR 2023-24

ele10 - Supplying Installing, testing and commissioning of Gun metal AIR RELEASE VALVE SIZE OF 25mm dia including cost of materials, labour, usage charges of machinery complete as per specifications.Complete Item no 15.86 page no 30 vol6 CSR 2023-24

ele11 - Supplying Installing, testing and commissioning of Gun metal Branch pipe size of 63mm dia and 19mm dia as per IS 903 complete including cost of materials, labour, usage charges of machinery complete as per specifications. Item no 15.87 page no 30 vol6 CSR 2023-24

ele12 - Supplying Installing, testing and commissioning of 19mm dia 40.0m length hose with rubber lining smooth bore, reinforced of natural/synthetic fibres, a rubber cover finish shall be smooth, fluted or fabric marked with minimum thickness of 1.50mm and to with stand a working pressure of 10Kgf/sqcm confirms and tested as per IS 444/ IS 12585 including cost of materials, labour, usage charges of machinery complete as per specifications. Item no 15.92 page no 31 vol6 CSR 2023-24

ele13 - Supplying, installing, testing and commissioning approved make heavy duty (Class c) GI pipes and fittings confirming to IS 1239 PI and II, Malleable Specials such as tees, long radius bends, check nuts, unions, flanges,nipples, etc including cutting, threading, welding/flanged joints with necessary GI washers, nuts, bolts etc., for pipes running in pipe shafts, ceiling, over terrace etc., as per drawing and specifications. The quoted rate shall include for necessary chasing in walls, making bore in walls etc., and making good the chased surfaces and bores in cement mortar etc. complete. Price is inclusive of Fittings like couplings, reducers, bends, Tees, etc and all fittings .The scope of work included with One coat of yellow/etching primer and 2 coats of red enamel paint Providing and fabricating MS supports using channel, angle, plates pipes, etc., to take the load of number of pipes and the dia of the pipes as per specification and drawings. Rate quoted shall include for supply and providing necessary welding, cutting, G.I U clamps, bolt nuts, washers, anchors fastener etc., as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slab trenches etc., to suit different dia pipes made of GI/MS rods, flats, etc., consists of strap, nuts washers, threaded rod etc., The rate quoted shall also include for giving one coat of zinc chromate primer and two coats of approved enamel paint for pipe supports. The pipe support shall be U type support using 50x50x6mm requires for supporting 80mm, 100mm and 150mm dia single pipe.The bracket inside the fire shaft shall be 100mm x50x5mm. Item no 15.97.2, 15.97.3, 15.97.4, 14.97.5, 15.97.7, 15.97.9, 15.97,10 page no 31 and 32 vol6 CSR 2023-24 200 mm dia.

ele14 - Supplying, installing, testing and commissioning approved make heavy duty (Class c) GI pipes and fittings confirming to IS 1239 PI and II, Malleable Specials such as tees, long radius bends, check nuts, unions, flanges,nipples, etc including cutting, threading, welding/flanged joints with necessary GI washers, nuts, bolts etc., for pipes running in pipe shafts, ceiling, over terrace etc., as per drawing and specifications. The quoted rate shall include for necessary chasing in walls, making bore in walls etc., and making good the chased surfaces and bores in cement mortar etc. complete. Price is inclusive of Fittings like couplings, reducers, bends, Tees, etc and all fittings .The scope of work included with One coat of yellow/etching primer and 2 coats of red enamel paint Providing and fabricating MS supports using channel, angle, plates pipes, etc., to take the load of number of pipes and the dia of the pipes as per specification and drawings. Rate quoted shall include for supply and providing necessary welding, cutting, G.I U clamps, bolt nuts, washers, anchors fastener etc., as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slab trenches etc., to suit different dia pipes made of GI/MS rods, flats, etc., consists of strap, nuts washers, threaded rod etc., The rate quoted shall also include for giving one coat of zinc chromate primer and two coats of approved enamel paint for pipe supports. The pipe support shall be U type support using 50x50x6mm requires for supporting 80mm, 100mm and 150mm dia single pipe.The bracket inside the fire shaft shall be 100mm x50x5mm. Item no 15.97.2, 15.97.3, 15.97.4, 14.97.5, 15.97.7, 15.97.9, 15.97,10 page no 31 and 32 vol6 CSR 2023-24 150 mm dia.

ele15 - Supplying, installing, testing and commissioning approved make heavy duty (Class c) GI pipes and fittings confirming to IS 1239 PI and II, Malleable Specials such as tees, long radius bends, check nuts, unions, flanges,nipples, etc including cutting, threading, welding/flanged joints with necessary GI washers, nuts, bolts etc., for pipes running in pipe shafts, ceiling, over terrace etc., as per drawing and specifications. The quoted rate shall include for necessary chasing in walls, making bore in walls etc., and making good the chased surfaces and bores in cement mortar etc. complete. Price is inclusive of Fittings like couplings, reducers, bends, Tees, etc and all fittings .The scope of work included with One coat of yellow/etching primer and 2 coats of red enamel paint Providing and fabricating MS supports using channel, angle, plates pipes, etc., to take the load of number of pipes and the dia of the pipes as per specification and drawings. Rate quoted shall include for supply and providing necessary welding, cutting, G.I U clamps, bolt nuts, washers, anchors fastener etc., as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slab trenches etc., to suit different dia pipes made of GI/MS rods, flats, etc., consists of strap, nuts washers, threaded rod etc., The rate quoted shall also include for giving one coat of zinc chromate primer and two coats of approved enamel paint for pipe supports. The pipe support shall be U type support using 50x50x6mm requires for supporting 80mm, 100mm and 150mm dia single pipe.The bracket inside the fire shaft shall be 100mm x50x5mm. Item no 15.97.2, 15.97.3, 15.97.4, 14.97.5, 15.97.7, 15.97.9, 15.97,10 page no 31 and 32 vol6 CSR 2023-24 100 mm dia.

ele16 - Supplying, installing, testing and commissioning approved make heavy duty (Class c) GI pipes and fittings confirming to IS 1239 PI and II, Malleable Specials such as tees, long radius bends, check nuts, unions, flanges,nipples, etc including cutting, threading, welding/flanged joints with necessary GI washers, nuts, bolts etc., for pipes running in pipe shafts, ceiling, over terrace etc., as per drawing and specifications. The quoted rate shall include for necessary chasing in walls, making bore in walls etc., and making good the chased surfaces and bores in cement mortar etc. complete. Price is inclusive of Fittings like couplings, reducers, bends, Tees, etc and all fittings .The scope of work included with One coat of yellow/etching primer and 2 coats of red enamel paint Providing and fabricating MS supports using channel, angle, plates pipes, etc., to take the load of number of pipes and the dia of the pipes as per specification and drawings. Rate quoted shall include for supply and providing necessary welding, cutting, G.I U clamps, bolt nuts, washers, anchors fastener etc., as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slab trenches etc., to suit different dia pipes made of GI/MS rods, flats, etc., consists of strap, nuts washers, threaded rod etc., The rate quoted shall also include for giving one coat of zinc chromate primer and two coats of approved enamel paint for pipe supports. The pipe support shall be U type support using 50x50x6mm requires for supporting 80mm, 100mm and 150mm dia single pipe.The bracket inside the fire shaft shall be 100mm x50x5mm. Item no 15.97.2, 15.97.3, 15.97.4, 14.97.5, 15.97.7, 15.97.9, 15.97,10 page no 31 and 32 vol6 CSR 2023-24 80 mm dia.

ele17 - Supplying, installing, testing and commissioning approved make heavy duty (Class c) GI pipes and fittings confirming to IS 1239 PI and II, Malleable Specials such as tees, long radius bends, check nuts, unions, flanges,nipples, etc including cutting, threading, welding/flanged joints with necessary GI washers, nuts, bolts etc., for pipes running in pipe shafts, ceiling, over terrace etc., as per drawing and specifications. The quoted rate shall include for necessary chasing in walls, making bore in walls etc., and making good the chased surfaces and bores in cement mortar etc. complete. Price is inclusive of Fittings like couplings, reducers, bends, Tees, etc and all fittings .The scope of work included with One coat of yellow/etching primer and 2 coats of red enamel paint Providing and fabricating MS supports using channel, angle, plates pipes, etc., to take the load of number of pipes and the dia of the pipes as per specification and drawings. Rate quoted shall include for supply and providing necessary welding, cutting, G.I U clamps, bolt nuts, washers, anchors fastener etc., as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slab trenches etc., to suit different dia pipes made of GI/MS rods, flats, etc., consists of strap, nuts washers, threaded rod etc., The rate quoted shall also include for giving one coat of zinc chromate primer and two coats of approved enamel paint for pipe supports. The pipe support shall be U type support using 50x50x6mm requires for supporting 80mm, 100mm and 150mm dia single pipe.The bracket inside the fire shaft shall be 100mm x50x5mm. Item no 15.97.2, 15.97.3, 15.97.4, 14.97.5, 15.97.7, 15.97.9, 15.97,10 page no 31 and 32 vol6 CSR 2023-24 . 25 mm dia.

ele18 - Supplying Installation testing and Commissiong of Micro process base Fire alram Control panel having power regulation Circuit, which conner to 230 AC to at S.D.C. Indicating FIRE-FAULT, Test facility also with work test facility arrangement, provided in the panel. All this electronic circuits componets are assembled in M.S.16 gauge suitable panel cabinet with glass Fraonted and locking arrangements including cost of all mateials etc. complete including cost of materials, labour, usage charges of machinery complete as perspecifications Item no 15.99.1 page no 32 vol6 CSR 2023-24 8 Zone.

ele19 - Supply Installation testing and Commissioning of conventional type photo/Heat electric smoke sensor with flashing LED capable of woking at 9V to 33 V DC .The Optical Smoke Detector is unaffected by wind or atmosphericpressure and operates over the temperature range minus 20 degree C to plus 60 degree C. IP Rating at IP 23D andApproval with EN- 54 -7, LPCB Approved. Item no 15.100 page no 33 vol6 CSR 2023-24

ele20 - Supplying Installing, testing and commissioning of Resettable type Manual Call point . works on 24V DC LED indicator with glass Fronted. Fire Symbol .The red Manual Call Point is approved to EN54-11 standard. MECHANICAL CONSTRUCTION The component parts of the call point are moulded in polycarbonate or ABS, depending on their function. Item no 15.101 page no 33 vol6 CSR 2023-24

ele21 - Supplying Installing, testing and commissioning of electronic Hooter, it conists of electronic circuit to give dual Fire alaram sound with works. 24V DC with speaker all encased in suitable in MS 16 gauge red painted box. complete including cost of materials, labour, usage charges of machinery complete as per specifications. Item no 15.102 page no 33 vol6 CSR 2023-24

ele22 - Supplying and fixing sheet metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. including cost of materials, labour, usage charges of machinery complete as per specifications. Item no 15.104 page no 33 vol6 CSR 2023-24

ele23 - Supplying and drawing of 2 Core X 1.5 Sqmm copper conductor armoured cable Item no 15.105 page no 33 vol6 CSR 2023-24

ele24 - Supplying Installing, testing and commissioning of 150mm dia 4 way Fire brigade inlet connection with Non retrn valve of 4 nos. 63 mm dia. including cost of materials, labour, usage charges of machinery complete as per specifications. Item no 15.123 page no 35 vol6 CSR 2023-24

ele25 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 Sl no 201 and 209 Iten no 32.05 nad 32.13 page 13 of 81 Vol 6 of CSR 2023-24 70 Sqmm, 3.5 Core, (18 GI Strips - 4 x 0.8 mm)

ele26 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 Sl no 201 and 209 Iten no 32.05 nad 32.13 page 13 of 81 Vol 6 of CSR 2023-24 16 Sqmm, 4 Core, (11 GI Strips - 4 x 0.8 mm)

ele27 - SupplyinganddrawingFlexibleMulticoreCablemanufacturedwithelectrolyticgradeflexiblecopperwithlowconductorconfirmingtoIS81301984and(Virgin)PVCinsulationsheathedsuitableforworking voltage upto 1100 Volts as per IS-694:1990 Item no 2.5.13 page no 6 Vol 6 of 2023-24 10C x 2.5 mm2

ele28 - GI/Copperstripsforgroundingconnections,usingnecessaryfixingmaterials as required. 25 x 6 mm GI strip item 2.58.3 page no 54 Vol 6 of 2023-24

ele29 - Supply and installation of wtaer cooler with the following specifications Refrigerant- R134a, Capacity- 80 L, Dimension- 1140x665x485 mm,Voltage- 230 V, Frequency- 50 Hz, Type of Product- Water Cooler, Model No- NST6080B,Storage Capacity- 80 L,Number of Taps- 2 Cold,Material- Stainless Steel,Weight (Kg)- 45 Kg,Current-2.5 A,Cooling Capacity-60 L/Hr, Normal Demand-300 Glasses Per Hour,Compressor Type- RECIP,Phase- 1 Phase,Water Over Flow Connections-1/2 BSP,Series- NST with transportaion installation charges etc complete

ele30 - Supply of HP or equivalent DESKTOP computer with 11th generation intel core i3 processor, windows 11 home 64 OS, 512 SSD, 8 GB DDR4-3200 MHz RAM(1 x 8 GB), Display size 19 inch moniter Antiglare; 250 nits, integrated graphics, 6 USB ports or higher (minimum 2 USB 3.0/3.1), 1 ethernet(RJ 45), 1 HDMI/Display port, headphone/microphone combo jack (3.5mm), VGA, DVD writer, 2PCI/PCIe slots or higher, 802.11 A/C(1x1) WLAN and bluetooth 4.2, preloaded MS office, pre loaded with latest version of Anitivirus, 1 year warranty

ele31 - Supply and fixing of Solar 10KWp, 3phase output off grid solar power plant on roof of MRF building of city corporation davanagere comprising of Solar PV cells, Batteries (150Ah x 10), inverter module mounting structure anodised aluminium, AJB, solar inverter with charge controller, cabaling, switch gear, ACDB/DCDB, cables and accessories, system earthing, lighting arrestor and energy meter etc complete as per engineer incharge of the work