Rural Works Department Tender

Excavation in Soil using Hydraulic Excavator including cutting and loding in Tippers,trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m) S.O.R Item No. 3.06

Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300-2. Rate per cum after adding royalty @ 27.48/Cum S.O.R. Item No. 3.17

Granular Sub-base with Close Graded Material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (By Mix in Place Method)With Grading-I Material S.O.R Item No. 4.01 B. (i)

Construction of dry lean cement concrete sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. S.O.R Item No. 6.01

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 S.O.R Item No. 6.4

Ordinary Kilometer stone (Precast) Kilo Metre Stone (Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) S.O.R. Item No. 8.14 (ii)

Direction and Place Identification Signs upto 0.9 sqm Size Board.(Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with area not exceeding 0.9 sqm fixed over back support frame of min 35 x 35 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing) For information at the start of the point S.O.R. Item No. 8.06

Retro-Reflectorised Traffic Signs Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. 60 cm x 45 cm rectangular S.O.R. Item No. 8.04 A (XII)

For turnings 60 cm equilateral triangle S.O.R. Item No. 8.04 A (iv)

Earth work in excavation of foundation in Ordinary Soil by Manual Means of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required a nd utilising the remaining earth locally for road work. S.O.R. Item No. 3.13 (i) B

Construction of dry rubble flooring at cross drainage works for relatively less important works. S.O.R. Item No. 16.09

Plain/Reinfoced Cement concrete in open foundation complete as per drwaing and technical specifications. PCC Grade M15 S.O.R. Item No. 12.08 A Case-ll

Stone Masonry Work in Cement Mortar 1:3 in Foundation complete as per Drawing and Technical Specifications. Random Rubble Stone Masonary in C.M. (1:3) in foundation S.O.R. Item No. 12.07 (B)

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and Technical Specifications Random Rubble Masonry Work in Cement Mortar 1:3 in S/S S.O.R. Item No. 13.04 A

Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and technical specifications. Square Rubble Coursed Rubble masonry (first sort) S.O.R. Item No. 12.07 (A)

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and technical specifications. Coursed rubble masonry (first sort) S.O.R. Item No. 13.04 B

Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications. Height upto 5m. PCC Grade M15 S.O.R. Item No. 13.05 A (p)

Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications. PCC Grade M20 S.O.R. Item No. 13.05 B (p)

Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications, RCC Grade M25 S.O.R. Item No.13.05 F (p)

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications S.O.R. Item No. 14.04

Supplying, fitting and placing HYSD bar reinforcement in sub structure complete as per drawing and technical specifications S.O.R No. 13.06

Plastering with cement mortar (1:3) on brick work in substructure as per technical specifications S.O.R. Item No. 13.03

Pointing with cement mortar (1:3 ) on brick or stone work in substructure as per Technical Specifications S.O.R. Item No. 13.02

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces S.O.R. Item No. 8.08

Providing & fixing 20mm thick compressible fiber board in expansion joint complete as per drawing and technical specification S.O.R. Item No. 14.17 (ii)

Providing weep holes in Brick masonry/ Plain/Reinforced concrete abutment , wing wall/ returen wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20 H towards drawing face. Complete as per drawing and technical specifications. S.O.R. Item No. 13.08

Back filling behind abutment, wing wall, return wall with Sandy material complete as per drawing and technical specifications. S.O.R. Item No. 13.09 (B)

Goods & Service Tax (G.S.T.) -

Labour Cess -