Drinking Water And Sanitation Department Tender
Search from across the categories, cities, and authorities to find the latest Jharkhand tenders. Every Jharkhand tender is curated from credible sources of government websites (eProcurement Jharkhand portal) and newspapers, thus ensuring the credibility of the information presented to you. For more information on Jharkhand tender bidder registration, the login process and more read the FAQs section on this page.
Costs
EMD
0Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_DWSD_73991_1Bid Award Id
ViewTender No
e - quotation No 06/2023-24 (2nd call)Tender Authority
Drinking Water And Sanitation Department ViewPurchaser Address
-Website
http://https://jalshakti-ddws.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Cost of consumable materials for above mentioned work such as grease, gland packing, packing paper, cotton waste, bulb etc required for jointing all suction and delivery pipe etc at site including repairing of sluice valve-1no and NR valves-1no.
2
-
-
Cost for supplying, installation and commissioning of motor control panel made of 2 mm thick cubical panel board heat and vermine proof, proper ventilated two coats of appoxy painted comprising of (A) Incoming feeder-
(i) 100 amp MCCB- 01 no.
(ii) 200 amp copper bus bar arrangemen(4pole)
(iii) Phase indicating lamp-03 nos.
(B) Out going feeder-
(i) 63 amp MCCB- 02 nos. (ii) Volt meter- 02 nos.
(iii) Amp meter-02 nos. (iv) Pilot lamp- 06 nos.
(v) Selector switch- 04 nos.
(vi) FASD (ml-03) starter-02 nos.
(vii) Single phase preventer-02 nos.
Complete internal wiring with suitable size of copper wire and testing on load.
1
-
-
Cost for supplying and laying of 16 mm² x 3 core copper cable PVC insulated and sheathed from panel to starter to motor.
30
-
-
Cost for supplying and fitting 100 amp change over switch of L&T /Havell’s/C&S make or ISI reputed make.
1
-
-
Raw Water Pumping Plant
-
-
-
Cost of dismantling the motor and taking out bowl assembly from the intake well by supplying all labour, tools and tackles etc at site.
2
-
-
Supplying all labour tools and tackles for complete dismantling and opening of 7.5 HP 3 phase VT motor, cutting burnt wire and rewinding super enameled copper wire , insulating paper, tape bamboo stick etc. Heating Varnishing and testing on full load at site including transportation charge after deducting the cost of scrap materials.
2
-
-
Cost for repairing of 7.5 HP VT pump make mather and platt supplying and fitting of pump shaft 1 no. top and bottom bush 2 no. intermediate bush 4 nos. lock 4 nos. CI impeller etc. all required materials as per requirement including dismantling and refitting all complete with all labour and tools after deducting the cost of scrap materials.
2
-
-
Making and fitting shaft coupling of sleeve muff.
4
-
-
Supplying and fitting intermediate rising main shaft bearing.
4
-
-
Cost for S/F of C.I. spider bearing with cut less rubber bush for suitable of 6” dia column pipe.
2
-
-
Cost for repairing with new making and fitting of stuffing box bush with gland packing tightner of in discharge head 7.5 HP VT p/sets with all labour and materials.
2
-
-
Cost for S/F of line shaft of S.S. non-magnetic materials as per sample.
2
-
-
Cost for fitting of sluice valve, N.R. valve, ¾”dia x 3” long bolt with nut and washer-36 nos. 6” diameter m.s. bent-01 No, flange 6” dia- 04 nos. cutting and welding of pipe to common header with gas cutter and welding set and making leak proof joint.
2
-
-
Cost of consumable materials such as grease, gland packing, packing paper, cotton waste, bulb, rubber insertion, nut bolt etc required for jointing all suction and delivery pipe etc at site.
2
-
-
Cost for supplying, installation and commissioning of motor control panel made of 2 mm thick cubical panel board heat and vermine proof, proper ventilated two coats of appoxy painted comprising of (A) Incoming feeder-
i) 100 amp MCCB- 01 no. ii) 200 amp copper bus bar arrangemen(4pole)
iii) Phase indicating lamp-03 nos.
(B) Out going feeder-
(i) 63 amp MCCB- 02 nos. (ii) Volt meter- 02 nos.
iii) Amp meter-02 nos. (iv) Pilot lamp- 06 nos.
(v) Selector switch- 04 nos.
(vi) FASD (ml-03) starter-02 nos.
(vii) Single phase preventer-02 nos.
Complete internal wiring with suitable size of copper wire and testing on load.
1
-
-
Cost for supplying and fitting 100 amp change over switch of L&T /Havell’s/C&S make or ISI reputed make.
1
-
-
Cost for supplying and laying of 16 mm² x 3 core copper cable PVC insulated and sheathed from panel to starter to motor.
30
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements