Public Works Department Tender

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

2 X4 sq. mm + 1 X4 sq. mm earth wire with p/f of Copper thimbles of required size and numbers with allied nuts and bolts to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape .

2 X 6 sq. mm + 1 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers with allied nuts and bolts to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape for Sub main nas AC points

2 X 10 sq. mm + 1 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers with allied nuts and bolts , to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. ( Anti backteria series of Schneider /ABB /L&T /Legrand make , )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 2 No's of 3 pin 5/6 A modular socket outlet and 2 No's of 5/6 A modular switch, connections etc. as required. ( Anti backteria series of Schneider /ABB /L&T /Legrand make)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.( Anti backteria series of Schneider /ABB /L&T /Legrand make)

Supply and laying of 25 mm dia medium class PVC medium grade Conduit to berecessed on walls / floor complete with all allied accrues like bends, tees etc. for paving way of laying of wires of haeting points /circuits ,machine points /circuits and sub mains .The Job includes cutting of walls / floors with required hydraulic cutter and refacing of walls with cement plaster of required ratio or with P.O.P after laying of conduits refacing to its original position by way of supply and applying of painting of required colour to effected area's.Anchor/Polycab/Finolex/TMT Plus make.

Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factornot less than 0.9, Service Value (CM/M/\N) minimum 6.00,Air deliveryminimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speedcontrol and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (ma.), insulation resistancemore than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, Installation testing and commissioning of 250 mm sweep Exhaust Fans of Usha / Crompton Greaves / Havel's incl making of necessary connections and making of necessary space in walls / Windows as per site.The Job includes providing and fixing of shutter of suitable size hylum sheet for fixing of exhaust fan

Supply and fixing of 18-20 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver. The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. Approved make Philips / Lighting techology / Trilux /wipro (to be approved before installation)

Supply and fixing of 12-15 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver,The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. Approved make Philips / Lighting techology / Trilux /wipro (to be approved before installation)

Supply ,installation ,Testing and Commissioning of 20-22 Watts ,4 ft long LED tube light fitting having PVC Body (Commercial type) of standard make dully isi marked ,incl ceiling rose and 2-core transparent wire for connections complete job.The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit initial system lumen output of 1400 lumens with minimum system efficacy of 120 lumen/watt. The luminaire shall comply to lifetime of 50000Hrs @ L70B50 with design ambient temp 45°C. The electronic driver used shall have a power factor ≥0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, THD≤10%, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I. The luminaire should be of Class B serviceability. The luminaire should be at least IP20 & IK02 rated. The minimum dimensions of the batten shall be 44mm X 51mm X 1157mm. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. Approved make Philips / Lighting techology / Trilux /wipro (to be approved before installation)

Supply ,installation ,Testing and Commissioning of 10-12 Watts ,2 ft long LED tube light fitting having PVC Body (Commercial type) of standard make dully isi marked ,incl ceiling rose and 2-core transparent wire for connections complete job.The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit initial system lumen output of 1400 lumens with minimum system efficacy of 120 lumen/watt. The luminaire shall comply to lifetime of 50000Hrs @ L70B50 with design ambient temp 45°C. The electronic driver used shall have a power factor ≥0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, THD≤10%, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I. The luminaire should be of Class B serviceability. The luminaire should be at least IP20 & IK02 rated. The minimum dimensions of the batten shall be 44mm X 51mm X 1157mm. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. Approved make Philips / Lighting techology / Trilux /wipro (to be approved before installation)

Supply ,Installation ,Testing and Commissioning of IP66 , 45-50 Watt LED Flood light Luminaries having Aluminium body of of standard make dully isi marked ,to be fitted on walls / poles with necessary cliffs /Clamps with nuts and bolts complete job.The system efficacy of the luminaire shall be ≥120lm/w. The LEDs used in the luminaire shall be from either Lumileds, Osram, Nichia, APT Electronics and CREE make, shall have CCT of 5700°K, CR≥70, SDCM≤5, Life of 50000Hrs @ L70B50. The luminaire shall have IP rating of IP66 & IK rating of IK07. The luminaire shall have lens made of polycarbonate & optical cover made of toughened glass. The LED driver shall have operating voltage range of 140V to 270V, PF≥0.95 @ full load, THD≤ 10% @ full load, In-built surge protection of 4KV, HV Cut off @ 325V (±15V). The luminaire shall have 10KV SPD in-built inside the luminaire. The maximum dimensions of the luminaire shall be, L: 264M, Depth: 52MM & height without cradle: 203MM. The nominal weight of the luminaire shall be maximum 2.4KGs. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material for approval. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. The Contactor has to provide replacement warrenty of fixture (if damaged /Burnt out what so ever reason ) for a period of two years reckoned from date of handing over the site to intending department. Approved make Philips / Lighting techology / Trilux (to be fitted on attic of building)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator) of Legrend /L&T /ABB /Simens make

8 way (4 + 24), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) of Legrend /L&T /ABB /Simens /Schinder make

16 way, Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioninq etc. as required of legrand / ABB /Schneider /L&T /Simens make

Supplying and fixing of 40 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens /Schinder make dully isi marked complete with connections.of Legrand / ABB /Schneider /L&T /Simens make

Supplying and fixing of 63 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens /Schinder make dully isi marked complete with connections

Supplying and fixing of 100 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens /Schinder make dully isi marked complete with connections.

Supply/ installation/testing and commissioning of Wall / floor mounted compartmentalized , 415 volts TPN MCCB Main Distribution panels ,fabricated out of sheet steel of 16 gauge dust protected, duly painted with powder coating ( not less than 80 microns ) incl earth terminal with all necessary accessories as required for panel (IP 54) with internal wiring of panel .The Panel is to provided and fitted with following adjustable type controlling /Protection switch gear devices (1) Normal Incoming (1A) 250 Amp TPN MCCB with breaking capacity of 50 KA thermo magnetic adjustable based of Legrend /Schinder /Simens / ABB make with extended rotory handle and phase spreaders on i/p and o/p side = 1 no (1B) 400 Amp TPN Aluminium Bus bar = 1 Set ( Bus Bar shall be insulated with heat shrinkable sleeves and shall be colour coded. having minimum size 20 mm x 10 mm with spacing as per latest IE Standards) (1C) One No. (1 No.) digital multifunctional meter for measurement of voltage ,current and power etc with Selector switch ,push battons and one set of CT's of ratio 250 A/5A ,CL 1.0 ,15VA . (1D) 3 No's (3 No's) phase indication lamps and 3 No.'s status indication lamp for ON / OFF /TRIP with Control SP MCB (2) Generator Incomer 100 Amp F.P Change over switch of Havels./HPL /Standard make = 1 no 200 Amp TPN Bus bar Al Strips = 1 Set ( Bus Bar shall be insulated with heat shrinkable sleeves and shall be colour coded. having minimum size 20 mm x 10 mm with spacing as per latest IE Standards) (1C) One No. (1 No.) digital multifunctional meter for measurement of voltage ,current and power etc with Selector switch ,push battons and one set of CT's of ratio 100 A/5A ,CL 1.0 ,15VA . (1D) 3 No's (3 No's) phase indication lamps and 3 No.'s status indication lamp for ON / OFF /TRIP with Control SP MCB (3) Generator Incommer 125 Amps DP MCB (10 KA) of Legrend /Schinder /Simens / ABB make = 1 No 200 Amp PN Bus bar Al Strips = 1 Set ( Bus Bar shall be insulated with heat shrinkable sleeves and shall be colour coded. having minimum size 20 mm x 10 mm with spacing as per latest IE Standards) (1C) One No. (1 No.) digital multifunctional meter for measurement of voltage ,current and power etc with Selector switch ,push battons and one set of CT's of ratio 100 A/5A ,CL 1.0 ,15VA . (1D) Phase Indicator Set (4) Outgoing . 125 Amps DP MCB (10 KA) of Legrend /Schinder /Simens / ABB make = 5 No 100 Amps Double Pole MCB (10 KA) of Legrend /Schinder /Simens / ABB make = 5 No 63 Amps Double Pole MCB (10 KA) of Legrend /Schinder /Simens / ABB make = 5 No The Panel manufacturing unit should be CPRI Registered with latest ammended IEC / IS 61439 and the Contractor has to submit the test certificate of main switch gear's and Drawing's of panel (Showing claerly dimensions of panel with spacing of switchgear as per IE Standards ) & is to approved by Department not less than the rank of SDO before manufacturing of panel.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3X120sq mm(45mm)

Supply,Laying,Testing & Commissioning of 120 sq.mm 31/ 2- core armored Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/paramount make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections. The cable is to be laid partially under ground including execuation and refilling back after cable laying and partially above ground including clipps etc.

Supply and laying of DWC double layer Corrigated pipe having 100 mm dia to be laid under ground upto 50 Cm's in deep including execuation and refilling back and disposal of surplus earth complete job.

Supply and installation of 4.5 to 5 KG ,Co2 Fire extinguisher having 5-years warrenty . Approved makes foamtech anti fire company , kanex fire , safex fire and safety ,supremex equipments ,reliance fire and safety ltd.

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoall coke and salt as required.The job includes providing and fixing of main hole PVC Chamber with its cover complete job

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supplying and fixing following modular Networking Socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

2 Module (75mmX75mm)

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply,Installation,Testing & Commissionig of 8-Port Managed Networking switches of Cisco / Juniper / D-Link make ,,Incl making of necessary connections by networking computer Engineer having following specifications Model :- • 8 x 10/100/1000BASE-T ports • 2 x 100/1000 Mbps SFP ports Port Standards :- • Ports 1 to 8 compliant with IEEE 802.3ab • IEEE 802.3i 10BASE-T Ethernet (twisted-pair copper) • IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper) • IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted-pair copper) • Auto-negotiation • IEEE 802.3x Flow Control • IEEE 802.3z 1000BASE-X Gigabit Fiber Performance :- :Switching Capacity: 56Gbps :Min. Packet Forwarding Rate: 41.7 Mpps :MAC Address Table: 8K and 4.1 Mbits Packet Buffer. :Static routing: 124 Static routes :Static MAC Entries: 256 entries : Power Supply: Internal AC Power Supply, Switch Category :- Gigabit Managed Switches Layer 2 Features :- Spanning Tree (STP) 802.1d : RSTP 802.1w , 802.1s MSTP : Loopback Detection : Link Aggregation LACP 802.3ad: Minimum 8 groups per :device and 8 ports per group ; Port Mirroring : One-to-One / Many-to-One : Jumbo Frame: 10K Bytes : Dual image & Dual configuration : Multicast Filtering

Supply & Installation of IP-20 & IK-08, UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, Vertical Mounting Rail 1.6 MM with 'U'Marking, with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19" angles with wall mounting provision on wall. Accessories like: 1 No of 19" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware, 1 No of 19" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.All as per pre approved by Engineer in charge/ For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR.

4 U Rack with Width 550 mm & length 450 mm & height 255 mm

Supply,Installation,Testing & Commissioning of 2000 KVA Power Inverter (24 Volts) Sine wave type of make (Sukam / Luminous / Exide / Micro tec/Liv guard make ).The invertor shall have inbuilt display unit showing input and output voltage ,Charging voltage , output current etc with having inbuilt protection device of suitable capacity . The invertor should invertor and UPS mode of operation . The job further includes Supply , Installation , Testing & Commissioning of 2 No's of 180 AH /12 V Tall tubular Inverter Batteries of same make as of inverter ,the batteries are to be housed in PVC Trplley , incl cost of pvc trolley. complete job.The job includes AMC of batteries and invertor for a period of three years ,which includes quarterly servicing of devices & as and when required. complete job.

Providing and laying of shock proof Rubber mats of 2mt. x 1 mt. and 12 mm thick in size of standard make dully isi marked

Supply,Installation,Testing and Commissioning of 63 Amps By PassChange over switch of Havells/HPL Make ,Incl its sheet steel enclosure and Angle iron stand and handle with making of necessary connections complete job.

Supply ,installation ,testing and commissioning of 4 KVA Relay type automatic aluminium round voltage stabilizer of Chinar / Liv Guard /Eq.make with input voltage of 85-306 volts thereby producing the desired output voltage with necessary dash fasteners including making of necessary connections.