Military Engineer Services Tender

Dismantling of ACSR conductor of any type & size from over head line or HT/LT poles with insulaters and channels and depositing to MES store yard, complete all as specified & directed.

Dismantling of PCC poles of any description in any position including taking out poles by breaking of PCC complete all as specified & directed.

M&L for point wiring one light / fan/ bell/Exhaust fan point controlled by one way switch(concealed type) complete with multi stranded copper conductor flame retardant low smoke (FRLS) 1.5 Sqmm size PVC insulated unsheathed cable 1100 volts grade drawn through with and incl medium grade duty concealed PVC conduit ISI marked not less than 20mm dia including conduit fittings and accessories such as socket,elbow,junction box, bell mouth,bend, reducer etc complete incl cutting chases in existing walls of any description built in cement mortar and making good the disturbed surfaces in cement mortar (1:4) and finishing the surfaces to match with existing surfaces and finish with using sunken type pressed steel terminal boxes of required sizes of not less than 1.6 mm thick factory made and factory painted with top cover of 3 mm thick plastic laminated sheet fixed with brass screws washers with all accessories including single core multi stranded copper conductor 1.5 Sqmm size PVC insulated unsheathed cable green in colour as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified . NOTE :-Wire/Cable colour coding Shall be maintained properly as per IE rule.

S&F switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed.

S&F Socket outlet 3 pin, 5A, flush type complete all as specified and directed.

Supply and fixing factory made epoxy powder coated distribution board, SPN, 8 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 200 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for one SPN/DP MCB as incomer and SP MCB outgoing, complete all as specified & directed .

Supply and fixing factory made epoxy powder coated distribution board, SPN, 2 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 100 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for one SPN/DP MCB as incomer and SPN/DP- MCB outgoing, complete all as specified & directed .

Supply and fixing MCCB 100 Amps rating 4 pole 35 KA having characteristics such as ICS=ICU=100% as per IS/IEC 60947-2, suitable for isolation, Class II front face, adjustable thermal setting =80-100% and magnetic setting =6-10 in single frame size upto 250A including dismantling of old/ damaged/ unserviceable MCCB 100 Amps, complete all as specified & directed. complete all as specified & directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 63 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified & directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified & directed.

M&L for PVC flat twin core cable wiring with two single core PVC insulated (unsheathes ) FRLS cable of size 16 sqmm and two single core PVC insulated (unsheathes ) complete all as specified & directed.

M&L for PVC flat twin core cable wiring with two single core PVC insulated (unsheathes ) FRLS cable of size 10 sqmm and two single core PVC insulated (unsheathes ) complete all as specified & directed.

M&L for PVC insulated weather prof flat twin core aluminium cableof size 2.50 sqmm single core including with PVC conduit of all necessary suitable iron clamps (03 Nos) nut and bolts of approprite size from juncation box to street light complete all as specified & directed

M&L for PVC pipe 25 mm wide on wall/ceiling (ISI marked, interlocking type) with all fitting ,complete all as specified & directed.

Supply and fixing wall mounted kitchen chimney comes with Baffle Filter is suitable for Indian kitchens and maximum suction power of 1500m3/hr with push button Suitable for kitchen size200 sqft & heavy frying /grilling control Autoclean Kitchen Chimney.Autoclean Alarm Baffle Filler (Black 90CM suitable for 4-5 Burners)complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 16 Sqmm 4 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 25 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 35 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 50 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 70 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 95 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area120 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area150 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

M&L for well burnt brick with sub class ‘B’ old size bricks for protection of cable complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for laying of cable etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

All as per Item No 28 above but depth exc beyond 1.50 m and not exc. 3.0 m complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

M&L for dry sand cushioning for UG cable in trenches including spreading levelling and hand paning and consolidating complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L for laying Galvanised iron tube 40 mm bore light grade (ISI marked) for cable protection to poles/under floor/under roads/alongwith walls complete including MS clamps of flat iron 25x3mm duly painted, GI nuts, bolts and washers & sealing of pipe ends with approved sealing compound, complete all as specified and directed..

M&L for laying Galvanised iron tube50 mm bore light grade (ISI marked) for cable protection to poles/under floor/under roads/alongwith walls complete including MS clamps of flat iron 25x3mm duly painted, GI nuts, bolts and washers & sealing of pipe ends with approved sealing compound, complete all as specified and directed..

M&L for laying Galvanised iron tube 80 mm bore light grade (ISI marked) for cable protection to poles/under floor/under roads/alongwith walls complete including MS clamps of flat iron 25x3mm duly painted, GI nuts, bolts and washers & sealing of pipe ends with approved sealing compound, complete all as specified and directed..

Cutting/ boring of road/hard standing to a size of 30cm in width and not exc 60 cm in depth for laying of protection pipe / water line/ cable including returning, filling in, spreading, romoval of surplus soil and providing 100mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate on top, complete all as specified & directed. Note : Due care shall be taken while deciding cable route for excavation. However any damage to Signal, BSNL, MES cable water/sewage pipe or any other service while excavation will be made good by the contractor and cost of the same for jointing material & labour is deemed to be included the cost of excavation.

M & L for providing plain cement concrete, type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in foundation of pole, filling and mass concrete complete all as specified and directed.

M & L for providing plain cement concrete, type B-1, 1:2:4 (using 40 mm graded stone aggregate) as in coping of pole, including necessary form work complete all as specified and directed.

M & L for steel tubular swaged poles in vertical position swaged type 410-SP-31, 9 Mtr long, ISI marked complete with cast iron base plate, finial taper plug, bolts, nuts washers and screws as required duly painted with two coats of aluminium paint over a coat of red oxide primer above ground level including painting throughout internally & below GL (externally) with two coats of bituminous paint, numbering of poles with cut stencil lettering in size 6mm thick and 50mm high and yellow and black strips of size 30cm width each with synthetic elamel paint upto 1.5m above coping etc including taking out /dismantling of old unserviceable poles, complete all as specified and directed. Note:- 1. Earth work and PCC will be measured and paid seperately under appropriate items.

S&F of Intergral LED security light luminaire 90W LED, 230 volts made up of pressure die cast aluminium housing powder coated with high power SMD LED’s lens & toughned glass IP-66, luminaire, mounted on & including GI bracket made out of 50mm bore medium grade pipe of 1.70m length, bent to required shape, fixed on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer, making connection with PVC copper conductor cable of 1.5 sqmm and taking down old unserviceable light fitting of any type/size, complete all as specified & directed.

S&F of integral LED security FLOOD light luminaire 120W LED 230 volts made of pressure die-cast aluminium housing with high power LED’s lens & toughned glass, IP-66 mounted on & including GI bracket made out of 50mm bore medium grade pipe of 1.70m length, bent to required shape, fixed on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer, complete all as specified & directed.

S&F of electronic meters temper proof LCD display with polycarbonate cover 230 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH, complete all as specified & directed.

S&F of meter cover box, single phase with locking arrangements, made of UV stabilized transparent polycarbonate/ flame retardant high grade engineering plastic, unique arrangement for pilfer proof interlocking with hinge type boxes, complying to IS:14772 and tested at CIPET, sealable optical port provision on the cover of the meter box, confirms to IP 54 requirement for environmental protection, complete all as specified & directed.

S&F of cable junction box, IP-66 insulated made out of PC-GFS polycarbonate, black colour (RAL 9011), environment friendly, recyclable, weatherproof (UV due to solar radiation, protected against rain water, temperature resistant), halogen & silicon free, anti-acid, anti-corrosive for outdoor installation of street light of size 225mm x 295mm x 122mm fixed on pole complete with links/terminals suitable for in/out XLPE cable size upto 35sqmm 3.5 core including MCB SP 6 Amps,10KA including necessary flat iron clamps with nuts, bolts & washers for fixing on pole, complete all as specified & directed.

Supply and fixing factory made epoxy powder coated distribution board, VTPN, 4 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 200 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for one FP-MCCB 160/250 Amp as incomer and SP TP MCB outgoing, complete all as specified & directed

S&F of stay Assembly using stay rod of 20mm dia with complete accessories as shown in Electrical Plate No 1 of SSR 2009 Part-I such as loop type insulator, porcelain, vitreous white/ brown or green, large size with overall dimensions 90x140mm clearance of hole 25.5mm, stay wire of size 7/4.00mm, stay plate 300x300x6mm thick, 14mm dia 400mm long GI stay bow, 20mm dia 1.80m long GI stay rod, galvanized thimble, etc., complete all as specified & directed. Note :- Earth work and PCC shall be measured and paid for separately).

Supply, installation, testing and commissioning of CPRI approved, factory made, LT panel board cubical, Outdoor type, floor mounted double door, 3 phase 4 wire, 50 cycles, 415 Volts. The panel board shall be made of 3.15mm thick CRCA sheet for load bearing members and 16 SWG (1.6 mm thick) for doors covers and internal partitions and shall be powder coated both side. Base frame of the panel shall be made of ICMC channel of size 50 x50 x 6mm, duly grouted on platform made of brick work in CM (1:2:4), 15mm thick plastering in CM (1:6) having minimum height of 600mm. The panel shall be provided with separate compartments for each switch gears with hinged door including interlocking with switch gears. The panel board shall be suitable for AC, 415 Volts, 50 Hz, 3 phase, 4 wire supply complete with epoxy insulated 400 Amps rated high conductivity aluminium bus bars, supported with DMC / SMC barriers and coluor coded, prewired with copper cable, 1100V Danger notice board on front of the panel & the degree of protection is IP-54. the panel shall be complete with instrumentation such as LED phase indicating lamps and CT's, including extended aluminium strip of rating of Incomer (400Amps), and outgoing as per rating of MCCB’s, including aluminium lugs to connect the cable etc., and comprising of the following:-

(a) MCCB 400 amps, 4 pole, 415V, 50Hz, AC Supply with breaking capacity 36KA (Adjustable thermal & fixed magnetic release) - 01 Nos (Incomer) (b) MCCB 160 amps, 4 pole, 415V, 50Hz, AC Supply with breaking capacity 16 KA (Adjustable thermal & magnetic release) - 05 Nos (outgoing) (c) MCCB 63 amps, 4 pole, 415V, 50Hz, AC Supply with breaking capacity 16 KA (Adjustable thermal & magnetic release) - 01 Nos (outgoing) (d) Digital Volts meter--01 Nos (e) Digital Ammeter meter--01 Nos (f) Indicator lamp RYB :01 Set (g) CT'S 200/5 01 Set

Supply, installation, testing and commissioning of CPRI approved, factory made, LT panel board cubical, Outdoor type, floor mounted double door, 3 phase 4 wire, 50 cycles, 415 Volts. The panel board shall be made of 3.15mm thick CRCA sheet for load bearing members and 16 SWG (1.6 mm thick) for doors covers and internal partitions and shall be powder coated both side. Base frame of the panel shall be made of ICMC channel of size 50 x50 x 6mm, duly grouted on platform made of brick work in CM (1:2:4), 15mm thick plastering in CM (1:6) having minimum height of 600mm. The panel shall be provided with separate compartments for each switch gears with hinged door including interlocking with switch gears. The panel board shall be suitable for AC, 415 Volts, 50 Hz, 3 phase, 4 wire supply complete with epoxy insulated 250 Amps rated high conductivity aluminium bus bars, supported with DMC / SMC barriers and coluor coded, prewired with copper cable, 1100V Danger notice board on front of the panel & the degree of protection is IP-54. the panel shall be complete with instrumentation such as LED phase indicating lamps and CT's, including extended aluminium strip of rating of Incomer , and outgoing as per rating of MCCB’s, including aluminium lugs to connect the cable etc., and comprising of the following:-

(a) MCCB 200 amps, 4 pole, 415V, 50Hz, AC Supply with breaking capacity 36KA (Adjustable thermal & fixed magnetic release) - 01 Nos (Incomer) (b) MCCB 63 amps, 4 pole, 415V, 50Hz, AC Supply with breaking capacity 16 KA (Adjustable thermal & magnetic release) - 06 Nos (outgoing) (c) Digital Volts meter--01 Nos (d) Digital Ammeter meter--01 Nos (e) Indicator lamp RYB :01 Set (f) CT'S 200/5 01 Set

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and connecting to main switch or switch board complete and incl PCC masonry pit of 300x300x300mm interior dimensions in PCC 1:2:4 type B-1 RCC cover with GI frame, charcoal and common salt 15cm in layers all round the earth plate, 15mm dia GI watering pipe, a funnel with wire mesh should be provided on top of watering pipe complete all as specified as per electric plate No 3 of SSR 2009 including testing after completion complete all as specified and directed.