Military Engineer Services Tender
Search from the latest JKtenders and find a business opportunity fitting your SME on the online platform of BidAssist. If you're wondering how to find the latest JK tenders or from where to get all the documents without the hassles, this is what we explain here. Find the best opportunities coming to the surface via the JK government, PSUs and state corporations.
Military Engineer Services - MES Tender
Civil And Construction
Pipe Line Project
Water Storage And Supply
Eprocure
Opening Date4 Nov 2024
Closing Soon2 Dec 2024
Tender Amount₹ 36,00,000
Costs
EMD
₹ 72,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_682289_1Tender No
GE/U- -2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Description all as per ser item No 1.00 here-in-before but capacity 7.5/5HP/3HP, complete all as specified and directed by Engineer-in-charge.
6
-
-
Supply & Fix parts in repair for single/double/multistage pumps of capacity 60/75/100 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge.
-
-
-
Pump impeller made out of Bronze.
5
-
-
Pump shaft stainless steel shaft complete with check nut and keys
5
-
-
Tyre coupling.
4
-
-
Star coupling
4
-
-
Gland cup with nuts and bolts
6
-
-
Shaft sleeves
6
-
-
Bearing housing
6
-
-
S&F parts for single/double/multistage pump of capacity 30/40/50HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge.
-
-
-
Pump impeller made out of Bronze.
4
-
-
Pump shaft stainless steel shaft complete with check nut and keys
1
-
-
Shaft sleeves
3
-
-
Casing bearing
3
-
-
Bearing housing
4
-
-
Tyre coupling/star coupling
3
-
-
Gland cup with nut and bolts
3
-
-
S&F parts for single/double stage pump of capacity 25/20/15/12/10HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge.
-
-
-
Pump impeller made out of Bronze.
4
-
-
Pump shaft stainless steel shaft complete with check nut and keys
4
-
-
Shaft sleeves
4
-
-
Casing bearing
3
-
-
Bearing housing
3
-
-
Tyre coupling/star coupling
5
-
-
Gland cup with nut and bolts
4
-
-
S&F parts for single/double stage pump of capacity 7.5/5HP/3HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge.
-
-
-
Pump impeller made out of Bronze.
5
-
-
Pump shaft stainless steel shaft complete with check nut and keys
2
-
-
Shaft sleeves
3
-
-
Casing bearing
4
-
-
Bearing housing
4
-
-
Tyre coupling/star coupling
5
-
-
Gland cup with nut and bolts
3
-
-
Disconnecting electric connection of 60/75/100 HP motor, removing the UNSV motor from existing place by unscrewing the foundation bolts and nuts decoupling from the pump, setting aside and transporting to workshop for repairs including dismantling the motor,cutting/taking out burnt winding of stator, rotor, cleaning the slots, transporting back after repair/winding & re-assembling the same. Cost of loading, unloading & transportation shall be deemed included in the quoted rates, complete all as specified and directed by Engineer-in-charge.
5
-
-
Note: Winding of motor stator & rotor shall be measured & paid separately.
(a) Rewinding of motor will be measured and paid separately under relevent item.
(b) The motor shall be squerrel cage induction motor.
(c) The rates quoted shall be deemed to include the cost of loading/unloading, transportation, grease, nuts, bolts and washers of any size and shape as required at site and refixing of serviceable motor duly functional and testing complete at its existing location/position complete all as specified and directed.
(d) Replacement of u/s bearings and grease completely.
(e) The contractor shall be arranged a workshop visit of Engr-in-Charge for each job and cutting complete burnt winding of motor in presence of Engr-in-Charge.
-
-
-
Description all as per ser item No 9.00 here-in-before but capacity 30/40/50HP motor, complete all as specified and directed by Engineer-in-charge.
4
-
-
Description all as per ser item No 9.00 here-in-before capacity of 25/20/15/12/10HP motor, complete all as specified and directed by Engineer-in-charge.
4
-
-
Description all as per ser item No 9.00 here-in-before but capacity of of 7.5/5HP/3HP motor, complete all as specified and directed by Engineer-in-charge.
6
-
-
Removing the burnt out winding from the rotor and stator, cleaning the slots, providing high quality of class 'B' paper insulation inside the slots, rewinding the motor of capacity 100/75/60/50/40/30/25/20/15/12/10/7.5/5HP/3HP with super enamel copper wire of same size and guage as per existing rapping up with high quality cotton tape and varnising with super quality oil including drying upto desired temperature and desired time, complete all as specified and directed by Engineer-in-charge.
Note:- Cost of labour for winding deemed to be included in the rate quoted.
220
-
-
S&F in replacement of Pump bearing No. 6307 C3 including taking down the old existing bearing, complete all as specified and directed by Engineer-in-charge.
8
-
-
S&F in replacement of Pump bearing No. 6308 2RS1/C3 including taking down the old existing bearing, complete all as specified and directed by Engineer-in-charge.
8
-
-
S&F in replacement of Pump bearing No. 6309 M/C3 including taking down the old existing bearing, complete all as specified and directed by Engineer-in-charge.
9
-
-
S&F in replacement of Motor bearing No. 6310 M/C3 including taking down the old existing bearing, complete all as specified and directed by Engineer-in-charge.
11
-
-
S&F in replacement of Motor bearing No. 6311 C3 including taking down the old existing bearing, complete all as specified and directed by Engineer-in-charge.
12
-
-
S&F in replacement of Motor bearing No. NU 304 ECP including taking down the old existing bearing, complete all as specified and directed by Engineer-in-charge.
7
-
-
Supply and fix in replacement of MS stud bolts of existing size with nuts suitable for pumps and motors of various capacity installed at installations, complete all as specified and directed by Engineer-in-charge.
20
-
-
M&L for spray painting of pump and motor, frame of capacity 60/75/100 HP including surface preparation by scrapping with hamery paper or grinder with two coat of synthethic enamel paint over one coat of red oxide primer of existing colour of approved make to the satisfaction, complete all as specified and directed by Engineer-in-charge.
8
-
-
M&L for spray painting of pump and motor, frame of capacity 20/30/50HP including surface preparation by scrapping with hamery paper or grinder with two coat of synthethic enamel paint over one coat of red oxide primer of existing colour of approved make to the satisfaction, complete all as specified and directed by Engineer-in-charge.
6
-
-
M&L for spray painting of pump and motor, frame of capacity upto 15HP including surface preparation by scrapping with hamery paper or grinder with two coat of synthethic enamel paint over one coat of red oxide primer of existing colour of approved make to the satisfaction, complete all as specified and directed by Engineer-in-charge.
6
-
-
M&L for writing the with brush about the machinery installed in different instalations eg Cap, discharge,MES No,Year of installation and head of the machinery on the wall in front of the pump motor with black paint including removing the existing paint with help of grinder, complete all as specified and directed by Engineer-in-charge.
22
-
-
M&L in replacement of aluminium lugs suitable for 240 Sqmm aluminium cable including taking down the existing unserviceable one, complete all as specified and directed by Engineer-in-charge.
32
-
-
M&L in replacement of aluminium lugs suitable for 185 Sqmm aluminium cable including taking down the existing unserviceable one, complete all as specified and directed by Engineer-in-charge.
60
-
-
M&L in replacement of aluminium lugs suitable for 95 Sqmm aluminium cable including taking down the existing unserviceable one, complete all as specified and directed by Engineer-in-charge.
50
-
-
Supply and laying in replacement of synthetic rubber insulated mats 10 mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006,( superseding IS 5424) suitable for electrical shock safety of sizes 2mx1m, complete all as specified and directed by Engineer-in-charge.
12
-
-
Supply and fix Gland packing type 3 of size 12 mm made of asbustus grip with silicon, complete all as specified and directed by Engineer-in-charge.
40
-
-
Description all as per ser item No 29.00 here-in-before but of size 16 mm thick, complete all as specified and directed by Engineer-in-charge.
40
-
-
M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) cement concrete in as in foundation filling of pole & stay, complete all as specified and directed by Engineer-in-charge.
10
-
-
M&L in replacement of PVC insulated heavy duty industrial cables single core copper conductor(flexible) PVC insulated cable 1100 volt nominal area of conductor 95 sqmm inculding taking down existing old unserviceable cable of complete all as specified and directed by Engineer-in-charge.
30
-
-
Description all as per ser item No 32.00 here-in-before but of size 70 Sq mm, complete all as specified and directed by Engineer-in-charge.
30
-
-
Description all as per ser item No 32.00 here-in-before but of size 50 Sq mm, complete all as specified and directed by Engineer-in-charge.
30
-
-
Supply only lithium base grease AP3 in 20 Kg pack suitable for application to ball bearing with operating temp 30 to 120 degree celsious drop point 174 degree celsious, colourlight fawn, complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F in replacement of load line MCCB 400 Amps 4 pole 415 volts with adjustable thermal and fixed magnetic setting of breaking capacity 36 KA,Ics=100% Icu including taking down the old existing MCCB, complete all as specified and directed by Engineer-in-charge.
1
-
-
S&F in replacement of MCCB 250 Amps 4 pole 415 volts with adjustable thermal and fixed magnetic setting of breaking capacity 36 KA,Ics=100% Icu including taking down the old existing MCCB, complete all as specified and directed by Engineer-in-charge.
2
-
-
Supply and Fixing in replacement MCCB TP 250 Amps , 415 Volts, 25 KA ,3 POLE, Ics=100% Icu , overload adjustable short circuit adjustable type incl complete connection with suitable spreaders, complete all as specified and directed by Engineer-in-charge.
2
-
-
Supply and Fixing in replacement MCCB TP 160 Amps , 415 Volts, 16 KA ,3 POLE, Ics=100% Icu , overload adjustable short circuit fixed type incl complete connection with suitable spreaders, complete all as specified and directed by Engineer-in-charge.
2
-
-
Supply and Fixing in replacement MCCB TP 100 Amps , 415 Volts, 16 KA ,3 POLE, Ics=100% Icu , overload adjustable short circuit fixed type incl complete connection with suitable spreaders, complete all as specified and directed by Engineer-in-charge.
3
-
-
Supply and Fixing in replacement MCCB TP 63 Amps , 415 Volts, 16 KA ,3 POLE, Ics=100% Icu , overload adjustable short circuit fixed type incl complete connection with suitable spreaders, complete all as specified and directed by Engineer-in-charge.
3
-
-
M&L for copper thimble suitable for 95/70 Sqmm single core copper cable including taking down the existing unserviceable one complete all as specified and directed by Engineer-in-charge.
20
-
-
M&L for copper thimble suitable for 50/35 Sqmm single core copper cable including taking down the existing unserviceable one complete all as specified and directed by Engineer-in-charge.
20
-
-
S&F MS clamp suitable for holding lead joints/leakages of 300 /250 mm bore of pipes any type made out of 40 mm x6 mm thick flat iron with M.S nuts bolts with flat washer 3mm thick -02 No for each complete all as specified and directed by Engineer-in-charge.
20
-
-
Description all as per ser item No 44.00 here-in-before but of size 200mm bore, complete all as specified and directed by Engineer-in-charge.
20
-
-
Description all as per ser item No 44.00 here-in-before but of size 150mm bore, complete all as specified and directed by Engineer-in-charge.
20
-
-
Description all as per ser item No 44.00 here-in-before but of size 100/80 mm bore, complete all as specified and directed by Engineer-in-charge.
20
-
-
Material & Labour for in replacement of steel nuts, bolts, washers of any size required at site, complete all as specified and directed by Engineer-in-charge.
30
-
-
Supply & fixing in replacement of Integral LED Flood light Luminaries 100 Watts consisting of suitable number of LEDs and mounted on MCPCB high pressure die cast aluminium housing with sealed toughened glass cover with secondary optics lens, IP 66 protection suitable for mast light mounting, 5700K, LED efficiency 130 lm/Watt and system efficiency 110 lm/W , 240 Volts AC, 50 Hz, CRI70% operating voltage range 160 V-270 V, Power factor 0.95, working temperature range -10ºC to 50ºC,built in surge protection of more than 10 kV , Confirm the tests from auth labs : LM79 & LM 80, incl proper fixing and testing of flood lights on 9/11 mtr long steel tubular pole and provide facility of power supply shall be provide as suitable for maint work of light fittings incl make proper connection of new and existing light fittings complete with cutting , welding , drilling holes, nut bolts, washer, complete all as specified and directed by Engineer-in-charge.
6
-
-
Material and labour for fabrication, supply, fixing and commissioning of box type display boards for installations of size not less than 1.5M x 1.0M x 0.2M made out of ACP sheet of 3mm thickness with english alphabets and numerics cut out and designed out of 3mm thick acrylic sheet neatly pasted on the ACP board with flushed LED strips running along the sides of the acrylic letters to be fixed on wall with necessary fixing arrangement ss per the site requirement on roof, wall etc, complete all as specified and directed by Engineer-in-charge.
Note:- (a) Before fabrication of the display board, the contractor has to produce a paper printout detailing all documents and matter to be displayed so as to get it inspected and passed by Engr-in-charge. (b) Matter to be displayed, colour of the ACP sheet and colour of Retro Reflective sheet will be as specified and directed by Engr-in-Charge. (c) The quoted rate is deemed to be inclusive of cost of labour and materials required for fixing of the display board at the location including providing electrical connections, complete all as specified and directed by Engineer-in-charge.
6
-
-
Material and labour for fixing of Layout diagram of pipe lay out / flow chart/ shock treatment chart etc of size 1.5M x 1.0M for power houses, sub stations and other E/M installations as per the requirement at various locations made out of pre laminated board with digital printing, pasting side beadings of decorative aluminium channel with proper fixing arrangement etc, complete all as specified and directed by Engineer-in-charge.
Note:- (a) Before for fabrication of the display board, the contractor has to produce a paper printout detailing all documents and matter to be displayed so as to get it inspected and passed by Engr-in-charge. (b) Matter to be displayed, colour of the ACP sheet and colour of Retro Reflective sheet will be as specified and directed by Engr-in-Charge. (c) The quoted rate is deemed to be inclusive of cost of labour and materials required for fixing of the display board at the location including providing electrical connections, complete all as specified and directed by Engineer-in-charge.
4
-
-
M&L Chemical spray (DC 226 contact cleaner) in container of 415 ml/300g for precision blended multipurpose product for prevents corrosion penetrates, lubricants, displaces and seals out moisture release rusted mechanism etc, complete all as specified and directed by Engineer-in-charge.
5
-
-
Material and labour for spraying herbicide (Round up) on area to remove unwanted vegitation/grass at various locations, complete all as specified and directed by Engineer-in-charge.
50
-
-
Material and labour for shifting heavy items /using excavator / cleaning areas / cleaning site by providing crane/hydra/excavators/tractors/trolley ect as required at site complete all as specified and directed by Engineer-in-charge.
20
-
-
Dismantling and taking down old u/s earthing complete with galvanised earth plate electrode 600mm x 600mmx 6.00mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 25x4 mm GI strip earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 40mm bore medium grade and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm bore GI pipe medium grade for watering and 40mm bore GI protection pipe (light grade), funnel, wire mesh, cast iron cover and frame etc, complete, all as specified or indicated and as directed including testing on completion, complete all as specified and directed by Engineer-in-charge.
5
-
-
Note : (i) The quoted rate shall include the cost of earth work, GI pipe for watering, GI protection pipe, funnel, wire mesh, RCC cover, etc. complete. RCC cover shall be 50mm thick in 1:2:4 type B-1 using 8mm bars @10cm c/c both way.
(ii) The quoted rate shall include the cost of the earth pit covers to be conspicuously marked of plate with stand grouted in PCC.
(iii) On testing after completion if the desired earth resistance is more than 2Ώ the earthing will be redone at no extra cost
-
-
-
Supply and fix indoor/outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x -400 Sqmm, complete all as specified and directed by Engineer-in-charge.
4
-
-
Supply and fix indoor/outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 240-300 Sqmm, complete all as specified and directed by Engineer-in-charge.
4
-
-
Supply and fixing indoor/outdoor end termination joint heat shrinkable 1100 Volts for XPLE cable of size 3.5 x 70-120 Sqmm, complete all as specified and directed by Engineer-in-charge.
6
-
-
Supply and laying, connecting and testing XLPE underground cable insulated, and overall sheathed with aluminium conductor heavy duty 1100 volts grade 150 sqmm 3.5 core laid in trenches/ on poles/ road crossing or passing through existing/new pipe under road crossing, clamping on wall etc, complete all as specified and directed by Engineer-in-charge. Note: (i) Earth work, sand, bricks , removing, returning filling Aluminium thimbles/lugs will be paid separately. (ii) Cost of laying electrical cable through new/existing pipe under road, buildings, railway tracks, highways are incl in the quoted rates. (iii) All equipments , machinery or tools if required for laying electrical cable through new/existing pipes are provided by the contractor without any extra cost.
70
-
-
Description all as per ser item No 59.00 here-in-before but of size 3.5 core 95 Sqmm, complete all as specified and directed by Engineer-in-charge.
70
-
-
M&L in replacement for 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm GI suspension wire, one twin core cable flat or circular of size 10 sqmm 2 core, complete all as specified and directed by Engineer-in-charge.
180
-
-
M & L for sand cushioning for cable with river washed sand and punning to provide required cover as per SSR part I, complete all as specified and directed by Engineer-in-charge.
8
-
-
Supplying and laying bricks common burnt clay sub class 'B' old size for cable protection, complete all as specified and directed by Engineer-in-charge.
800
-
-
Dismantling and taking down old unsv LT Panel and Supplying, installing, testing & commissioning indoor type cubical panel board outer shell made out of 3.15 mm thick CRCA sheet and inner shell made out of 2 mm thick and MS angle section 50x50x6 mm suitable for floor mounted with nuts & bolts , frame factory fabricated with front and back openable double door system and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable/openable with arrangement of pad locking on both doors incl 2 no. of pad locks of three keys shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, incl Copper bus bar of 600 A , tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS:8623/93 comprising of the following, complete all as specified and directed by Engineer-in-charge.
1
-
-
(a) Supply and fixing MCCB 400 Amps, 36 KA 4 pole 415 Volts AC, adjustable type, complete all as directed by Engg-in-charge (incoming)-01 Nos. (b) Supply and fixing ON Load change over 400 Amps,4 pole 415 V AC, (IC)-01 Nos. (c) Out going MCCB TP 160 Amps 36 KA adjustable type - 3 Nos (d) Star delta starter with contactor for 100 HP 02 Nos (e) Interconnection of MCCBs ,Change Over to Busbar with copper strip of suitable size with PVC insulated colour coaded heat shrinkable type sleeves - 1 Job
-
-
-
(f) RYB indication LED type, 22.5 mm dia, protected with MCB SP 2 Amp showing 3 phase supply -03 Nos (g) Digital Ammeter of range 0-400 A, auxiliary voltage 230 volts with selector switch -01 Nos (h) Volt meter of range 0-500 Volts, auxiliary voltage 230 volts with selector switch -1 Nos (j) Single phase preventer , Over load /under voltage relay , Phase sequence corrector 01 job (k) Misc items like screws, cable tie, copper cable 1.5/2.5 Sqmm, cable lugs, sleeves, cable glands etc complete
-
-
-
Note for item No 64.00
(i) The quoted rate shall includes minor items such as lugs, nuts & bolts, washers, top insulators, sleeves, provision of extra holes in bus bar etc.
(ii) All internal wiring shall be done with suitable size of PVC insulated solid copper conductor FRLS cable conforming to IS-694.
(iii) Panel drawing shall be got approved before placing of order from Engr-in-Charge/GE.
(iv)The bus connection for cable from main bus bar to outgoing MCCB will be connected through suitable rating bus bar strip type duly insulated (v) Cable will be entered in panels through gland. (vi) Cost of marking description on the front door as per direction of Engr-in-Charge is incl in quoted rate.
-
-
-
Material and labour for repair of valve pit chamber of any size not less than 1.2 mtr x1.2mtrx 900 mm necessary brick work, cement mortar / plastering in brick work,PCC ,welding work of hinges and MS sheet cover,painting on welding works ,MS sheets and plastered surface, complete all as specified and directed by Engineer-in-charge.
10
-
-
Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth,foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. and taking out/laying of pipe lines of soft/loose soil. Complete all as specified and directed by Engr-in-Charge.
225.54
-
-
Returning, filling in, including spreading, leveling, watering and well ramming in layers, each layer not exceeding 25cm thick after pipes have been laid and tested complete all as specified and directed by Engineer-in-charge.
196.66
-
-
Removing excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.
22.88
-
-
Taking up or down CI/DI/MS water mains pipe 300 mm bore (including all fittings), with flanged/welded butt joint/ spigot and socket ends and lead joints including burning out joints and recovering lead, complete all as specified and directed by Engineer-in-charge. Note : (i) Unserviceable items retrieved from site should be deposited in MES store by the contractor.
(ii) cost of transportation of unsv materials from site to MES store deemed to be included in the quoted rates.
42
-
-
Refixing MS/DI/CI pipe obtained from item No. 4 above and connections in new or old position (walls, trenches, ceiling and floors etc) of size 300 mm bore complete inlcuding main / branch connections, complete all as specified and directed by Engineer-in-charge.
6
-
-
Supply, laying, jointing and testing MS ERW pipe class 'B' of bore 300 mm having wall thickness 6 mm with permissible tolerance + 10% conforming to IS-3589, ISI marked alongwith circular welding joints laid in trenches/ along road/ on surface/ slopes/pillars/ culverts/ causeways etc, complete all as specified and directed by Engineer-in-charge.
36
-
-
Taking up or down old unseviceable GI pipe of size 150 mm dia including all fittings, complete all as specified and directed by Engineer-in-charge. Note : (i) Unserviceable items retrieved from site should be deposited in MES store by the contractor.
(ii) cost of transportation of unsv materials from site to MES store deemed to be included in the quoted rates.
78
-
-
Refixing GI/CI pipe obtained from Item No. 07 above and connections in new or old position (walls, trenches, ceiling and floors etc) of size 150 mm dia complete including main branch connections, complete all as specified and directed by Engineer-in-charge.
6
-
-
Supply & fixing GI pipes of size 150 mm dia, medium grade, galvanized with all fitting such as bends, tees, nipples, union and sockets, clamps etc laid in trenches, under floor/walls etc, complete all as specified and directed by Engineer-in-charge.
72
-
-
Taking up or down old unseviceable GI pipe of size 100 mm dia including all fittings, complete all as specified and directed by Engineer-in-charge. Note : (i) Unserviceable items retrieved from site should be deposited in MES store by the contractor.
(ii) cost of transportation of unsv materials from site to MES store deemed to be included in the quoted rates.
72
-
-
Description all as per ser item No 75.00 here-in-before but of size 80 mm dia and cradit is the property of the contractor, complete all as specified and directed by Engineer-in-charge.
150
-
-
Description all as per ser item No 75.00 here-in-before but of size 50 mm dia and cradit is the property of the contractor, complete all as specified and directed by Engineer-in-charge.
300
-
-
Description all as per ser item No 75.00 here-in-before but of size 40 mm dia and cradit is the property of the contractor, complete all as specified and directed by Engineer-in-charge.
200
-
-
Description all as per ser item No 75.00 here-in-before but of size 25 mm dia and cradit is the property of the contractor, complete all as specified and directed by Engineer-in-charge.
350
-
-
Description all as per ser item No 75.00 here-in-before but of size 20 mm dia and cradit is the property of the contractor, complete all as specified and directed by Engineer-in-charge.
400
-
-
Refixing GI/CI pipe obtained from Item No. 75 above and connections in new or old position (walls, trenches, ceiling and floors etc) of size 100 mm dia complete including main branch connections, complete all as specified and directed by Engineer-in-charge.
12
-
-
Description all as per ser item No 81.00 here-in-before but of size 80 mm dia obtained from item No. 76, complete all as specified and directed by Engineer-in-charge.
18
-
-
Description all as per ser item No 81.00 here-in-before but of size 50 mm dia obtained from item No. 77, complete all as specified and directed by Engineer-in-charge.
60
-
-
Description all as per ser item No 81.00 here-in-before but of size 40 mm dia obtained from item No. 78, complete all as specified and directed by Engineer-in-charge.
60
-
-
Description all as per ser item No 81.00 here-in-before but of size 25 mm dia obtained from item No. 79, complete all as specified and directed by Engineer-in-charge.
60
-
-
Description all as per ser item No 81.00 here-in-before but of size 20 mm dia obtained from item No. 80, complete all as specified and directed by Engineer-in-charge.
60
-
-
Supply & fixing GI pipes of size 100 mm dia, medium grade, galvanized with all fitting such as bends, tees, nipples, union and sockets, clamps etc laid in trenches, under floor/walls etc, complete all as specified and directed by Engineer-in-charge.
60
-
-
Description all as per ser item No 87.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engineer-in-charge.
132
-
-
Description all as per ser item No 87.00 here-in-before but of size 50 mm dia, complete all as specified and directed by Engineer-in-charge.
240
-
-
Description all as per ser item No 87.00 here-in-before but of size 40 mm dia, complete all as specified and directed by Engineer-in-charge.
140
-
-
Description all as per ser item No 87.00 here-in-before but of size 25 mm dia, complete all as specified and directed by Engineer-in-charge.
290
-
-
Description all as per ser item No 87.00 here-in-before but of size 20 mm dia, complete all as specified and directed by Engineer-in-charge.
340
-
-
Decoupling, disconnecting sluice valve of size 300 mm taking down from pipe line opening all parts, derusting, cleaning, overhualing comprising of repairs/replacement of unserviceable parts of sluice valve and taking to workshop for repairs. Reassembling of sluice valve and fixing on its original position, complete all as specified and directed by Engineer-in-charge. Note :(i) Loading/unloading & transportation charges shall be deemed included in the quoted rates. (ii) S&F of spare parts shall be measured and paid separately under respective item
4
-
-
Stem bush bronze
3
-
-
Gland flange cast iron
3
-
-
Stud/Bolt carbon steel
4
-
-
Stem nut/chaknut
4
-
-
Stem Stain less steel
2
-
-
Decoupling, disconnecting sluice valve of size 250 mm taking down from pipe line opening all parts, derusting, cleaning, overhualing comprising of repairs/replacement of unserviceable parts of sluice valve and taking to workshop (if reqd) for repairs. Reassembling of sluice valve and fixing on its original position, complete all as specified and directed by Engineer-in-charge. Note :(i) Loading/unloading & transportation charges shall be deemed included in the quoted rates. (ii) S&F of spare parts shall be measured and paid separately under respective item
3
-
-
Stem bush bronze
3
-
-
Gland flange cast iron
3
-
-
Stud/Bolt carbon steel
3
-
-
Stem nut/chaknut
3
-
-
Stem Stain less steel
2
-
-
Decoupling, disconnecting sluice valve of size 200 mm taking down from pipe line opening all parts, derusting, cleaning, overhualing comprising of repairs/replacement of unserviceable parts of sluice valve and taking to workshop (if reqd) for repairs. Reassembling of sluice valve and fixing on its original position, complete all as specified and directed by Engineer-in-charge. Note :(i) Loading/unloading & transportation charges shall be deemed included in the quoted rates. (ii) S&F of spare parts shall be measured and paid separately under respective item
5
-
-
Stem bush bronze
5
-
-
Gland flange cast iron
4
-
-
Stud/Bolt carbon steel
4
-
-
Stem nut/chaknut
5
-
-
Stem Stain less steel
5
-
-
Decoupling, disconnecting sluice valve of size 150 mm taking down from pipe line opening all parts, derusting, cleaning, overhualing comprising of repairs/replacement of unserviceable parts of sluice valve and taking to workshop (if reqd) for repairs. Reassembling of sluice valve and fixing on its original position, complete all as specified and directed by Engineer-in-charge. Note :(i) Loading/unloading & transportation charges shall be deemed included in the quoted rates. (ii) S&F of spare parts shall be measured and paid separately under respective item
8
-
-
Stem bush bronze
6
-
-
Gland flange cast iron
4
-
-
Stud/Bolt carbon steel
4
-
-
Stem nut/chaknut
8
-
-
Stem Stain less steel
4
-
-
Supply fabrication and fixing MS joints like bends Tee, tapers, collars, elbow, tail piece (any type) caps, plugs up to 100 mm to 150 mm bore, complete all as specified and directed by Engineer-in-charge.
200
-
-
Supply and fix Nut bolt M-16 (50mm length) & M-20 (75mm length) with 02 (each 5mm thick) Nos washer at each set, complete all as specified and directed by Engineer-in-charge.
25
-
-
Supply and fixing leather gasket including replacement old UNSV gasket for 200 mm, complete all as specified and directed by Engineer-in-charge. Note:- (i) Contractor fully responsible for necessory excavation for replacement of gaskit work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate.
15
-
-
Supply and fixing leather gasket including replacement old UNSV gasket for 150 mm, complete all as specified and directed by Engineer-in-charge. Note:- (i) Contractor fully responsible for necessory excavation fo rreplacement of gaskit work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate.
15
-
-
Supply and fixing in replacement of cast iron non return valve, conforming to IS-5312, suitable for 150 mm bore pipe, heavy duty ,both end flanged of pressure rating PN 1.6 and jointing with rubber or fibre board gasket with nuts, bolts and washers, welding wk including taking down old unsv, complete all as specified and directed by Engineer-in-charge.
2
-
-
Description all as per ser item No 101.00 here-in-before but of size 100 mm dia, complete all as specified and directed by Engineer-in-charge.
1
-
-
Description all as per ser item No 101.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engineer-in-charge.
2
-
-
Description all as per ser item No 101.00 here-in-before but of size 50 mm dia, complete all as specified and directed by Engineer-in-charge.
4
-
-
M&L for repair to leaking run lead joints in CI/DI spigot and socket end pipe line of 300 mm bore by providing new lead ,using good quality spun yarn, including necessary excavation, returning filling in trenches in any type of soil,bailing out water, and at any depth, complete all as specified and directed by Engineer-in-charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate.
(ii) Required extra fittings/pipe will be measured and paid separately.
20
-
-
Description all as per ser item No 105.00 here-in-before but of dia 250 mm bore pipe, complete all as specified and directed by Engineer-in-charge.
15
-
-
Description all as per ser item No 105.00 here-in-before but of dia 200 mm bore pipe, complete all as specified and directed by Engineer-in-charge.
12
-
-
Description all as per ser item No 105.00 here-in-before but of dia 150 mm bore pipe, complete all as specified and directed by Engineer-in-charge.
13
-
-
Material and labour for repair to leaking flanged/circular welding joints of 100 to 200 mm bore MS/GI pipe line by providing rubber or fiber board gasket, new flanges if required at site, nut bolts, washers and welding works where required etc, including necessary excavation, returning filling in trenches in any type of soil, bailing out water, and any depth, complete all as specified and directed by Engineer-in-charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate.
(ii) Required extra pipe will be measured and paid separately..
25
-
-
Description all as per ser item No 109.00 here-in-before but of dia 250 to 300 mm bore pipe, complete all as specified and directed by Engineer-in-charge.
25
-
-
S&F of Gun-metal, globe or gate valves, 50 mm dia , heavy duty, with iron wheel head, screwed both ends (ISI marked), complete all as specified and directed by Engineer-in-charge.
20
-
-
Description all as per ser item No 111.00 here-in-before but of size upto 40 mm bore, complete all as specified and directed by Engineer-in-charge.
20
-
-
Description all as per ser item No 111.00 here-in-before but of size upto 25 mm bore, complete all as specified and directed by Engineer-in-charge.
40
-
-
Description all as per ser item No 111.00 here-in-before but of size upto 20 mm bore, complete all as specified and directed by Engineer-in-charge.
60
-
-
Description all as per ser item No 111.00 here-in-before but of size upto 15 mm bore, complete all as specified and directed by Engineer-in-charge.
30
-
-
M&L for cutting of existing road for crossing of MS/DI/CI/GI pipes for laying of any size pipes including necessary exacavation and earth work including repairing the same as per existing, complete all as specified and directed by Engineer-in-charge.
10
-
-
M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) cement concrete in as in foundation filling of pole & stay, complete all as specified and directed by Engineer-in-charge.
10
-
-
M&L for Premix ready mix road repair patching compound for instant road repair manufactured with a blend of bitumen, aggregates and high grade polymer to ensure immediate bonding with existing surface available in bag of 25 Kg, complete all as specified and directed by Engineer-in-charge.
10
-
-
Supply and fixing GI fittings medium grade ISI marked including complete all as specified and directed by Engineer-in-charge.
-
-
-
Elbow 15mm
20
-
-
Elbow 20mm
40
-
-
Elbow 25mm
35
-
-
Elbow 40mm
20
-
-
Elbow 50mm
20
-
-
Elbow 80mm
10
-
-
Socket 15mm
20
-
-
Socket 20mm
70
-
-
Socket 25mm
50
-
-
Socket 40mm
25
-
-
Socket 50mm
10
-
-
Socket 80mm
10
-
-
Union 15mm
20
-
-
Union 20mm
50
-
-
Union 25mm
45
-
-
Union 40mm
20
-
-
Union 50mm
20
-
-
Union 80mm
10
-
-
Elbow reducer 20 x 15mm
20
-
-
Elbow reducer 25 x 20mm
50
-
-
Elbow reducer 40 x 25mm
30
-
-
Socket reducer 15x20mm
10
-
-
Socket reducer 25x20mm
30
-
-
Socket reducer 40x25mm
30
-
-
Socket reducer 40x20mm
30
-
-
Socket reducer 50x25mm
30
-
-
Nipple 15 x50mm
20
-
-
Nipple 15 x 75 mm
10
-
-
Nipple 15 x 100 mm
15
-
-
Nipple 15 x 150 mm
15
-
-
Nipple 20 x50mm
40
-
-
Nipple 20 x 75mm
20
-
-
Nipple 20 x100mm
40
-
-
Nipple 20 x 150mm
25
-
-
Nipple 25 x 50mm
40
-
-
Nipple 25 x 75mm
20
-
-
Nipple 25 x 100mm
40
-
-
Nipple 40 x 50mm
20
-
-
Nipple 40 x 100mm
20
-
-
Nipple 40 x 150mm
20
-
-
Nipple 50 x 50mm
20
-
-
Nipple 50 x 100mm
20
-
-
Nipple 50 x 150mm
20
-
-
Tee 15mm
20
-
-
Tee 20mm
50
-
-
Tee 25mm
40
-
-
Tee 20x15mm
10
-
-
Tee 25x20mm
30
-
-
Tee 40x15mm
10
-
-
Tee 40x20mm
25
-
-
Tee 40x25mm
25
-
-
Tee 50x25mm
20
-
-
Dead plug 15mm
12
-
-
Dead plug 20mm
30
-
-
Dead plug 25mm
20
-
-
Dead plug 40mm
15
-
-
Dead plug 50mm
15
-
-
lead
75
-
-
Spunyarn
40
-
-
Material and labour for taking down by scraping and preparation the surface of the header approx 6 mtr long with sluice valve and NRVs at pump houses, OHT including repainting one coat of super quality of black enamel paint with one under coat of primer etc, complete all as specified and directed by Engineer-in-charge.
8
-
-
Supply and fixing in replacement of cast iron sluice valve of size 200 mm (PN 1.6) (ISI Marked) with iron wheel head, both end flanged, stainless steel spindle, non rising type complete with neoprene rubber gasket, nuts, bolts and washers, necessary welding wk etc.including taking down old unsv, complete all as specified and directed by Engineer-in-charge.
1
-
-
Description all as per ser item No 121.00 here-in-before but of size 150 mm dia, complete all as specified and directed by Engineer-in-charge.
2
-
-
Description all as per ser item No 121.00 here-in-before but of size 100 mm dia, complete all as specified and directed by Engineer-in-charge.
2
-
-
Description all as per ser item No 121.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engineer-in-charge.
2
-
-
Material and labour for fabrication of MS sheets ,angle iron in replacement of old pit cover with necessary welding work and one coat of red oxide primer to the welded works and painted with black enamel paint, complete all as specified and directed by Engineer-in-charge.
200
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%