Bhakra Beas Management Board Tender

Providing and fixing 5 mm thick asbestos ceiling sheet

Dismantling cement conglomerete floor 25 mm to 50 mm thick without conc. Base

Providing and laying vitrified floor tiles in different sizes in light colour shades made using Soluble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement: 4 fine sand), complete. (Soluble salt Print Penetration should be up to 1 to 2 mm after the tiles are fired & polished). (A) Size 600x600 mm

8" thick hollow block masonry 1: 5 in Super structure

Scraping white wash and colour wash.

Cement plaster 12.5 mm thick in 1 : 5

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish

Distempering with acrylic washable oil bound distemper of approved manufacture two coats over one priming coat to give an even shade.

Removing door and window (steel or wood) with chowkhat by making necessary recesses in walls when the wall not to be dismantled a ) door of area 3 sqm and below

b) window of area 3 sqm and below (Including Ventilators & Excluding Joinery 2- W2)

Providing and fixing M.S. angle iron 40x40x6mm chowkhat including iron hold fasts butt hinges fixed in position, finished with red lead non setting primer complete in all respect (a) Single Rebate door

(b) Double Rebate door

Providing and fixing M.S. round or square bars at required spacing in wooden frames of windows and clearstory windows.

Deodar wood door shutter and window shutter including hinges, screws, and cords etc. complete fixed in position. (a) panelled, glazed or glazed and panelled

Providing and fixing wire gauge door shutter with kail wood without springs housed chowkets (Single leaf) (a). 35mm thick

Supplying and fixing glass panes with glazing clips and special metal sash putty of approved make.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Applying priming coat with metal primer on new steel or wood work including preparation of surface.

Painting two coat with synthetic enamel paints in all shades on wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint.

Cement concrete 1:3:6 with stone ballast of shingle

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 200 x 300 mm, 100x200mm, 200x200mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Finishing wall with exterior decorative cement based paint such as snowcem ,robbiacem etc. two coat to give an even shade.

Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge ) complete in all respect. (a)   (ii) C.P. brass Bib cock foam flow without flang

Butt Hinges (All items ISI Marked) Anodized Aluminum Mat Finish (a) Anodized Aluminum Mat Finish (i) 125mm x 75mm x 4mm.

Providing and fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS 1868 ) transparent of died to required color with nuts and screws etc Complete

Providing and laying, jointing fixing and testing G.I pipe line B-class including cost of special such as tees , bends ,sockets ,elbows etc. painting with anticorrosive bitumastic paint threading inside build and complete. (c) 25 mm dia I/D

Providing and fixing in position chinaware anglo indian water closer with P Trap or S Trap (to the approval of Engineer-In-charge ) suit consisting of 10 Ltr PVC flushing cistern ISI market supported on angle Iron Short bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer In-charge.

Providing and fixing jet spray with 2’-6” long PVC pipe with C.P. Brass nut

Providing and fixing in position Chinaware Indian Orisa water closet size 580x440 mm of approved make (to the approval of the Engineer-in-charge) complete in all respect

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect.

Providing and fixing vitreous chinaware pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 30mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. C.I. work as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. (a) 100 mm.......330mm

Providing, Laying , fixing & jointing of P.V.C.Pipes as per ISI-4985 (ISI marked with the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications. (ii) 75 mm o/d pipe of 10 Kgf ./ Sqcm

iv ) 110 mm o/d pipe of 10 Kgf ./ Sqcm

Providing and fixing in position CP brass soap dish fixed into wall with rawl plugs C.P. Brass screws and complete in all respects

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank.

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100 volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- (i) a Wiring fan point (Without fan box

ii) Wiring light point

iii ) Wiring call-bell point

v ) Wiring 6Amp. wall socket point

vi ) Wiring 16/20Amp. power plug control point

MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: MINIATURE CIRCUIT BREAKERS: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- (ii) MCB Single Pole 6-32amp. (10kA, Curve-C)

PVC INSULATED FR COPPER CONDUCTOR CABLES:- Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- iv ) Overall size 4sq.mm (Un-sheathed)

Overall size 6 Sq mm (Un-sheathed)

XLPE INSULATED ARMOURED CABLES (LOOSE):- Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-iii) Overall size 16sq.mm (2Core) Armoured (Loose)

Provision for Unforseen Items