Military Engineer Services Tender

S&F in replacement for Ultrasonic digital water level indicator carrying out following works :- Ultrasonic sensor :- Digital display through ultrasonic sensor with electronic buzzer alarm,with the capability to observe the water depth in mter as per the requriment uptyo 18 Meter hight/depth. This system should operate on 220V/440V AC.Ultrasonic sensor input power supply should be 24 VAC +- 10% Type 2/4 wire,dead band 450mm for up to 18 meter , beam angle (a) : 12 degree / 14 degree /5 degree applied material PP/PVDF/ABS/PC housing ingress protection aganist short circuit , process tem:- 10 degree to 60 degree ambient temp :- 10 degree to 55 degree operating pressure atmospheric accuiracy +- 0.2 % of measured distance + 0.05 % of range ) Resolution ( depende on distance ) : 1mm to 10 mm output : Analog : 4-20MA Top mounted. LCD display controller having 2 relay 4 output contact rating 230V AC, 7 Amp configurable as control output onj separate set ponits with pre defiend logic with 7 segments LED supported by 4 key tack - tile keybord input will be 4-20 mA liner with resolution Supply 230V AC 50 Hz & output 24 VDC 120 mA.Supply of Alart system through electronic Buzzer alarm on emepty or full tank position with electronically Auto on/Auto off with a suitable gap with timer system & push button to reset the buzzer.Supply of enclosure and fram of SS to hang the sensor , all the accessories fitted should be in power coated paint CRC sheet cabinet,Supply of 3 core shielded copper wire 1.5 Sqmm (As per site requriment) complete all as specified and directed.

Supply,install,commissiong in repair Ultrasonic Flowmeter of dia 250 mm, 4 - 20 mA DC, Line Size : DN80 Pressure Rating : 10 kg/cm2 Design of measuring sensor : Flange ANSI 80 Flange Material : Carbon Steel Sensor Lining : Hard Rubber ,Electrode Material : SS 316L Earthing Rings : SS 316,Measuring Tube : SS 304 Coil Housing : Carbon Steel ,Protection Class : IP 65 complete all as specified and directed.

Supply and Fixing rotational moulded polyethy lene water stroge tank (cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part I. of size 5000 Ltrs complete all as specified and directed.

Demolition of cement concrete (unreinforced) in floors and pavings n.exc 15 cm thickness (below or above ground level) and debris out side MD land complete all as specified and directed.

M & L for cement concrete 1:2:4, type B-2 (using 40 mm graded stone aggregate) as in support of CI/DI pipes, Pump set foundation and hardstanding finishing even and fair without using extra cement complete all as specified and directed.

M&L in replacement of motor base frame made out of angle iron structure as per existing size . Pump set removed from old base frame with disconnection of electric and water lines.Taking of old base frame with and unservicable Nut , Bolts and PCC etc.Nacessary grouting of new Nuts , Bolts and PCC work for mounting of new base frame and Pumpset refixing on the same including necessary testing complete aal as specified and directed.

Supply , installation and testing of centrifugal type pump set with induction motor of capacity 30 HP or next higher capacity ,self priming, total head 70 mtr of water column , electric driven , 3 Phase , 415 volts at 50 mtr head including providing electric connections, suitable foundation with base frame as per manufacturer drawing, Coupling , cut to requried length and making holes for fixing of motor and pumps,grouting in foundation , including painting with two coats of synthetic enamel paint black colour over a coat of red oxide primer,necessary civil work , anti vibration pad,proper alligement , vaccum gauge at suction and pressure gauge at dilivering side , connection to existing header and connecting with suction and discharge water mains, eccentric/ coccentric fittings complete all as specified and directed.

Taking out existing U/S CI sluice valve of any size any pattern up to 250 mm bore from 80 mm bore complete all as specified and directed.

S & F in repair sluice valves,cast iron body, flanged end drilled and non rising type SS spindle with long body, class P N 1.6, of size 100 mm dia including flange joint with rubber or fiber board, bolts, nuts and wahers of complete including pumping out accumulated water compelte all as specified and directed.

All as per Item No 12 Above but 150 mm dia complete all as specified and directed.

All as per Item No 12 Above but 200 mm dia complete all as specified and directed.

All as per Item No 12 Above but 250 mm dia complete all as specified and directed.

Taking out existing U/S NRV of size upto 200 mm bore complete all as specified and directed.

Suply and Fixing cast iron NRV flanged end of size 200 mm dia with all fitting and accessories .

All as per item 17 above but 150 mm dia complete all as specified and directed.

All as per item 17 above but 100 mm dia complete all as specified and directed.

Supply & fixing in repair of centrifugal type pump set with induction motor of capacity 7.5 HP or next higher capacity ,self priming, total head 70 mtr of water column , electric driven , 3 Phase , 415 volts at 50 mtr head including providing electric connections, suitable foundation with base frame as per manufacturer drawing, Coupling , cut to requried length and making holes for fixing of motor and pumps,grouting in foundation , including painting with two coats of synthetic enamel paint black colour over a coat of red oxide primer,necessary civil work , anti vibration pad,proper alligement , vaccum gauge at suction and pressure gauge at dilivering side , connection to existing header and connecting with suction and discharge water mains, eccentric/ coccentric fittings complete all as specified and directed.

Taking down existing asbestos cement pressure pipes of 150 mm dia , any class and position incl all fittings, assessories and fixtures etc of following bore pipe complete all as specified and directed.

Supply, laying, connecting, jointing and testing ductile iron pressure pipe of size 150 mm(6") inch dia , ISI marked suitable for "push on joints" in standard working lengths supplied with rubber gasket duly ISI marked for water supply, Class K-7 with socket and with cement mortar lining inside the metalic zinc coating with finishing layer of bituminious paint on outside the pipe complete all as specified & directed.

Supply, laying, connecting, jointing and testing ductile iron pressure pipe of size 200 mm(8") inch dia , ISI marked suitable for "push on joints" in standard working lengths supplied with rubber gasket duly ISI marked for water supply, Class K-9 with socket and with cement mortar lining inside the metalic zinc coating with finishing layer of bituminious paint on outside the pipe complete all as specified & directed.

Supplying fixing and testing of DI pipe fittings (Specials) heavy duty for any type ( flanged/socketed) pipes such as, bends (any type radius, and angle), tapers, any type straight bend, increasing, decreasing, or double socket etc) Tee pieces, ring branch, Y junction, double branch, Cross (all socket or socket and spigot), collors, caps and plugs, adopters etc of any size radius and length confirming to IS specifications up to 150 mm bore complete all as specified and directed.

Disconnecting and taking down old existing PVC tubing and connections of any description/ grade and in any position in trenches/under floors / on walls etc including all fittings/accessories and fixtures such as bends, union, elbow socket, valves, taps etc, all as directed and specified for 20 mm dia pipe complete all as specified and directed.

All as per item No. 25 here in above but 25 mm dia complete all as specified and directed.

All as per item No. 25 here in above but 50 mm dia complete all as specified and directed.

All as per item No. 25 here in above but 80 mm dia complete all as specified and directed.

All as per item No. 25 here in above but 100 mm dia complete all as specified and directed.

Supply and Fixing in any length UPVC pipe 20 mm dia pipe manufactured as per ASTM-D-1785 as per IS-559, Schedule-40 complete with fittings, laid in trenches in required length complete all as specified and directed

All as per item No. 30 here in above but size 25 mm dia complete all as specified and directed.

All as per item No. 30 here in above but size 50 mm dia complete all as specified and directed.

All as per item No. 30 here in above but size 80 mm dia complete all as specified and directed.

All as per item No. 30 here in above but size 100 mm dia complete all as specified and directed.

Excavation in trenches in soft / loose soil n exc 1.5 mtr wide and not exc 1.5 m in depth etc complete and getting out in soft soil inciuding trimming sides and bottom of trenches complete all as specified and directed.

Returning filling in trenches including watering and well ramming in layer not exc 25 cm thick in soft/ loose soil complete all as specified and directed.

Removing excavated surplus soil to a distance not exc 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting pointall complete all as specified and directed.

Hard standing cutting/road cutting for laying of pipe and making surface good with PCC 1:3:6 complete all as specified and directed.

NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.