Department Of Public Works And Highways Tender

Description Republic Of The Philippines Department Of Public Works And Highways Butuan City District Engineering Office Regional Office Xiii Butuan City, Agusan Del Norte Invitation To Bid For Contract Id No. 24gnd0002- Supply And Delivery Of Additional Laboratory Equipment For Use In The Dpwh-butuan City District Engineering Office (quality Assurance Section) The Dpwh Butuan City District Engineering Office, Through The Fy 2024 General Appropriations Act (gaa) Intends To Apply The Sum Of P 5,000,000.00 Being The Abc To Payments Under The Contract For Contract Id No. 24gnd0002 – Supply And Delivery Of Additional Laboratory Equipment For Use In The Dpwh-butuan City District Engineering Office (quality Assurance Section). Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Dpwh Butuan City District Engineering Office Now Invites Bids For The Above Procurement Project, As Follows: Item No. Item Description Quantity Unit 1 Dynamic Cone Penetrometer (dcp) Standard: Astm D 6951-03 This Portable Hand Operated Equipment Is Designed To Obtain A Direct And Rapid In-situ Evaluation Of The Structural Strength Of Road Pavement Layers Constructed With Unbound Materials. The Test Is Performed With Continuous Penetrations At Approx 800 Mm Depth With Max. Depth Of 2 M By Using Extension Rods. The Equipment Housed In Carrying Case, Consists Of: - Drop Sliding Hammer 8 Kg Weight, Falling Height Of 575 Mm - Impact Anvil With Driving Rod - Penetration Rod With Conical 60° Point And Ø 20mm - Bar Wrench, Spanners, Accessories. Dimensions: 1210x340x190 Mm Weight: 29 Kg Approx 1 Set 2 Drilling Accessories For Spt (50m) Jam Hammer Drive Assy 1 Assy 3 Jarring Plate 2 Pcs 4 Aw Rod 3.0 M 10 Pcs 5 Aw Rod 1.5 M 8 Pcs 6 Aw Rod 1.0 M 6 Pcs 7 Spt Tube Sampler 4 Pcs 8 Nq Head Assy (head Adaptor Aw Box To Nq Pin) 3 Pcs 9 Nw Casing Head (head Adaptor Aw Box To Nw Pin) 3 Pcs 10 Cross Bit 3 Pcs 11 Nq Hoisting Plug (pulling Plug) 3 Pcs 12 Water Swivel 3 Pcs 13 Water Swivel Hose 3/4" X 10 M 3 Pcs 14 Tools Pipe Wrench 24 In 3 Pcs 15 Pipe Wrench 36 In 4 Pcs 16 Tripod 1 Pcs 17 Blaine Air Permeability Apparatus To Determine The Fineness Of Cement Standards: En 196-6, Comparable To: Astm C204 I Aashto T153 I Bs 4359:2 Used To Determine The Fineness Of Portland Cement In Terms Of The Specific Surface Expressed As Total Surface Area In Square Centimeters Per Gram Of Cement. The Apparatus Is Supplied With: - Glass U-tube Manometer With Valve - Steel Stand - Test Cell With Disk And Plunger All In Stainless Steel - Rubber Aspirator Bulb - 1000 Filter Paper Disks -manometric Liquid - Vaseline Grease For Better Coupling Tube/cell - Funnel - Brush Dimensions: 220x180x470 Mm Weight: 12 Kg Approx. Accessory: Glass Thermometer - 10 To +50 °c. 1 Set 18 Offer: Stainless Steel Test Sieve 18" Dia. Mesh Opening No. 12 1 Pc 19 Cbr/marshall 3 Speed Load Frame, Digital Touch-screen, Computerized Digital And Computerized, The Frame Is Provided Of Three Fix Speed Ranges, Easily Selectable By An Electric Switch: 1.0 Mm/min. For Cbr Tests (australian And Old Bs Standards) 1.27 Mm/min. For Cbr Tests 50.8 Mm/min For Marshall Tests. Supplied Complete With "cyber-plus 8 Evolution" System, Load Cell, And Displacement Transducer. 1 Unit Accessories: - Load Piston - Stability Mould Ø 4" - Cbr Mould Complete With Collar And Perforated Base: Ø 6" (152.4 Mm) X 7" (177.8 Mm) Height - Spacer Disc With "t" Handle: Ø 5 15/16" (150.8mm) X 2.416" (61.4 Mm) Height Perforated (sweel) Plate With Adjustable Stem Tripod (dial Gauge Support) Dial Gauge 10mm Range, 0.01 Mm Subd. Annular Surcharge Weight 2270g Slotted Surcharge Weight 2270 Solid Base Plate For Cbr Mould Delivery Of The Goods Is Required As Per Request By The End-user Within 120 Calendar Days Upon Receipt Of The Notice To Proceed (ntp). Bidders Should Have Completed, Within 10 Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. Prospective Bidders May Obtain Further Information From Dpwh Butuan City District Engineering Office And Inspect The Bidding Documents At The Address Given Below During Office Hours From 8:00 Am To 5:00 Pm. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On February 02, 2024 – February 21, 2024 From The Given Address And Website(s) Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of P 5,000.00. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person, By Facsimile, Or Through Electronic Means. The Dpwh Butuan City District Engineering Office Will Hold A Pre-bid Conference On February 09, 2024 At 2:00 Pm At Dpwh - Butuan City District Engineering Office Noa Hall, Which Shall Be Open To Prospective Bidders. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below. Late Bids Shall Not Be Accepted. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. Bid Opening Shall Be On February 21, 2024 At Dpwh - Butuan City District Engineering Office Noa Hall At 2:30 Pm At The Given Address Below. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. The Schedule Of Key Procurement Activities Is Shown Below: Issuance Of Bidding Documents February 02, 2024 – February 21, 2024 Hard Copies At Bac Secretariat Of This Office Downloadable @ Dpwh Website Www.dpwh.gov.ph And Philgeps Website Www.philgeps.gov.ph Pre-bid Conference February 09, 2024 @ 2:00 Pm Dpwh- Butuan City Deo Noa Hall Deadline For Submission Of Bids February 21, 2024 @ 2:00 Pm Dpwh- Butuan City Deo Noa Hall Opening Of Bids February 21, 2024 @ 2:30 Pm Dpwh- Butuan City Deo Noa Hall The Dpwh Butuan City District Engineering Office Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Head, Procurement Staff: Bac Chairperson: (sgd)teresita E. Pagar (sgd)grace T. Curayag Engineer Iii Oic, Assistant District Engineer Dpwh- Butuan City Deo Dpwh- Butuan City Deo Tel. No. (085) 225-2022 Local 84661 Tel. No. (085) 225-2022 Local 84608 You May Visit The Following Websites: For Downloading Of Bidding Documents: Philgeps And Dpwh Websites For Online Bid Submission: Philgeps And Dpwh Websites Date Of Publication: February 02, 2024 – February 21, 2024