Drawer Tenders

Details: Description:- Modification /alteration /augmentation Of Existing Hitachi Make Electronic Interlocking (ei) Systems As Per Rdso/spn/192/2019 Ver. 2.0 Or Latest (with Latest Amendment), As Per Approved signaling Plan And Selection Table/locking Table Of Stations In Connection With Provision Of Rgm/ttm siding At Kwj, Gha, Kkp, Gjut And Pja Stations, Technical Specifications & Conditions Of Contract. This includes - 1) Design & Drawing Of Indoor Circuit Diagram. 2) Modification To The Existing Application software Of Vdu & Mt. 3) Modification To The Existing Interface & Interlocking Circuit For Stations. 4) alteration To The Existing Relay Rack Wiring As Per The Modified Interface Circuit For Stations. 5) modification To The Existing Ccip At Stations. 6) Upgradation Of Datalogger Data Base. 7) Necessary modification In Existing Pi/rri Panel. 8) Supply Of Additional Ei Hardware Modules/cards For Doing The alteration At Above Mentioned Stations. 9) Fat And Sat As Per The Modified And Approved Application logic. 10) Installation, Wiring, Programming, Testing & Commissioning Of Complete Yard For Data In Put & Configuration, Simulation & Functional Testing, Diagnostic & Trouble Shooting And Commissioning Of electronic Interlocking System As Per Signal Interlocking Plan. Installation Is To Be Done As Per Rdso specification No. Rdso/spn/192/2019 Ver. 2.0 Or Latest And Rdso Practice Circulated Vide Tan No. sts/e/tan/3012, Ver. 2.0, Dt.10.08.2016, Tan No. Sts/e/tan/3007, Ver. 1.0, Dt. 02.11.2012 And Tan no. Sts/e/tan/3006, Ver. 3.0, Dt. 08.01.2025 For Earthing And Bonding Scheme (as Applicable) For electronic Interlocking. (inspection By Rdso)

Description: CATEGORY: Prewired for LED tube complete Make Havells or Bajaj or Philips or Crompton , Steel Screw full thread with rawl plug 1 1 by 2inch size ISI Marked 100 screw per pkt , PVC switch board snow white size 7inchx4inch for sockets and switches Make Supreme or Polycab or Finolex , PVC switch board snow white size 8inch x 10inch for main switches oblique DB Make Supreme or Polycab or Finolex , PVC L bend and T junction joint for PVC casing and capping confirming to IS 3419 Part 3 Make Supreme or Polycab or Finolex , Switch socket combination snow white multipurpose 2 in 1 15 Amp 230 Volts Make Anchor or SSK or CONA , Switch socket combination snow white 5 Amp 230 Volts Make Anchor or SSK or CONA , Service bracket 40mm dia GI Tubing medium grade 1 point 5 Mtr Long Make Jindal or Tata or Kalinga , Service cable PVC insulated aluminium conductor 1100 volt grade Heavy duty served with inner sheathing of PVC tap as per TS , Ceiling Rose three terminal snow white Make Anchor or SSK or CONA , LED Bulk head fitting high pressure die cast aluminum front cover with glass cover with specially design gasket with LED lamp 10 watts Make Havells or Bajaj or Philips or Cropmtion , PVC Flexible wire copper conductor multi stranded 0 point 0016 oblique 76 Make havells or Finolex or Plaza , PVC Flexible Conduit pipe 15 mm dia Make Polycab or Supreme or Finolex , PVC Round oblique Square Block Make Polycab or Supreme or Finolex , Fire extinguisher of 1 kg of dry power type conforming to IS 13849 along with its accessories Make Cease fire or Omex or Alfa Fire , Earthing plate 600 x 600 x 6 mm Galvanised steel suitable for GI strip fittings, drilled with 2 nos holes for 6 mm dia near one side , CI Earth Pit Cover of size 300 x 300 x 6 mm with Angle iron frame of size 20x20mm 3 mm thick with MS frame , Funnel fitted with 20 mm diameter GI Pipe 1 point 5 m Long Pipe Make Jindal or Tata or Kalinga , GI wire 4 mm diameter for earthing , Charcoal , Salt normal , Air terminal single pointed aluminium rod 12mm dia and 300mm long , Testing point terminal block make of Gun metal and phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw , Aluminium strips 25x3mm , Galvanised iron strip 32x6mm , Funnel fitted with 20mm dia GI Pipe 1 point 5m long Make Jindal or Tata or Kalinga , Earthing Plate 600x600x6mm GI steel suitable for GI strip fittings drilled with two nos holes for 6 mm dia near one side , CI earth pit cover of size 300x300x6mm with angle iron of size 20x20x3mm thick with MS frame , Insulating PVC block 75x75x30mm with insulating clamp nut and bolt Make Presto or Polycab or Finolex , Study chair of size length 56 Cm Height 82 Cm and Width 56 Cm Type Lacquered finish with arm seat and back cushion velvet upholstery Make Supreme or equivalent , Study Table of size 4ft X 2ft Wooden top on round tube structure with three drawers on one side , Steel almirah of size 1855mm with 4 shelves MS sheet doors and and locker 1 point 00mm thick lock material brass and steel finished and thickness of shelves 0 point 90mm , Mild Steel rack adjustable sheet 1 point 00mm thick nuts and bolts are in hexagon blck steel overall height 1 point 755m depth 0 point 410m and width 0 point 915m , Hand Held Trolley of size 1200 x 900 x 1200 mm of 2 mm thick MS plateform and size of wheel 127 mm with loading capacity minimum 200 kg and overall weight of trolleys 19 Kg

Description: CATEGORY: BULL DOG CLIP PACK OF 12 NOS N7540-STY-179 , CLIP BOARD PLASTIC OMEGA N7520 000852 , CORRECTING FLUID PEN UNI GERMAN N7540 P02763 , DIVISIONAL FOLDERS DISPLAY BOOK 60 PKTS WITH COLOUR PAPE N7540 063107 , DOUBLE PUNCH DP 280 KANGAROO N7520 000853 , DRAWING PIN 1.9 CMS 1 PKT 50 NOS N7540 STY 105 , DUSTER MAGNETIC FOR WHITE BOARD N7540 P063110 , ENVELOPE FOR DO LETTER PACK OF 100 NOS N7540 STY 111 , ENVELOPE SE 4 PACK OF 100 NOS N7540 STY 68 , ENVELOPE FOR SE 6A WITH CLOTH PACK OF 50 NOS N7540 STY 71 , ENVELOPE FOR SE 7A WITH CLOTH PACK OF 50 NOS N7540 STY 73 , ENVELOPE SE 8A WITH CLOTH PACK OF 50 NOS N7540 STY 75 , ERASER NON DUST APSARA JUMBO PACK OF 20 NOS N7540 P063099 , EXERCISE BOOK SQ RULLED PACK OF 10 NOS N7540 STY 77 , FLAT RULER 12 N7540 STY 146 , GLUE STICK KORES 15 GMS N7540 P062765 , L FOLDER PLASTIC PACK OF 10 NOS N7540 P063121 , LAMINATED COLOUR SHEETS FOR COVERING OF REGISTERS 1 ROLL 5M N7540 P063105 , LAMINATION POUCH A4 SIZE 1PKT 10 NOS N7540 P062802 , LEXI 05 PEN 1PKT 10 NOS N7520 000855 , NOTE BOOK MINUTING PAD N7540 STY 5 , PAPER PIN ASSORTED 100 GM VIKRAM PKT N7540 P062785 , PATTI FOLDER PACK OF 10 NOS N7540 P063120 , PEN UNIBALL UB 157 N7520 000860 , PENCIL HB PLATINUM 1PKT 10 NOS N7510 002416 , PERMANENT MARKER REYNOLD N7540 P062781 , PILOT PEN V 5 N7520 000858 , PIN HOLDER OMEGA N7540 P062788 , POST IT PAD 3X2 3M BRAND N7540 P062796 , POST IT PAD 3X3 3M BRAND N7540 P062797 , POST IT PAD 3X5 3M BRAND N7540 P062799 , REGISTER RULED 2 QRS N7540 STY 65 , REGISTER RULED 4 QRS N7540 STY 63 , SHORTHAND BOOK N7540 STY 81 , SIGNAL FOLDER FOAM TYPE 2 O RINGS N7540 P063093 , SIGNATURE FLAP 1X4 SET OF 04 PADS EACH OF 20MMX50MM N7540 P063108 , SIGNATURE FOLDER 2-O RING BINDER 25 MM CAPACITY N7540 P063095 , SIGNATURE FOLDER CLIP FILE LEVER FILE N7540 P063094 , SIGLE PUNCH KANGAROO N7520 000854 , STAMP PAD N7540 STY 178 , STAPER NO 10 KANGAROO N7520 000 850 , STAPLER PIN 24 6 N7540 P062804 , STAPER PIN FOR NO 10 N7540 P063762 , TAG COTTON 6 BUNDLE 100 NOS N7540 STY 186 , TAG COTTON 8 BUNDLE 100 NOS N7540 STY 187 , TAG COTTON SMALL BUNDLE 100 NOS N7540 STY 185 , TRANSPARENT INSERTION SHEET PACK OF 10 NOS N7540 P063096 , TWINE HEMP 4 OZ BUNDLE N7540 STY 190 , U CLIP 28MM PLASTIC PKT N7510 002428 , U CLIP 35MM MS VIKRAM PKT PLASTIC N7510 002429 , WHITE BOARD MARKER REYNOLD N7540 P062782 , OHP PEN SET FABRE CASTLE N7520 000 863 , HIGHLIGHTER SET LUXOR N7520 000861 , PAPER CUTTER L N7540 P062789 , RULER PLASTIC 18 N7540 STY 147 , TWINE JUTE N7540 STY 191 , STAPLER 24 6 KANGAROO N7520-000851

Description: CATEGORY: Note Pad No 33 80 Sheets in 1Pad , Good quality gift wrapping paper , Metal Paper Punching Machine small No. 480 , Slip 3 x 3 3M , Metallic Binder clips 19 MM , Parker Classic Stainless Steel Refillable Ball Pen With Chrome Trim , Self-inking Stamps , Copier PaperA-3 , Executive diary , Metal Single Punch 4.5 mm , Cotton Table Duster , WIRO notebook A5 , Metallic Binder clips 25 MM , DO Paper - 90 GSM Per Rim , Slip 3x5 3M , Pakcing Sutli cotton Per Roll , Wet Tissue Paper packet , Color Pencils in 12 colors , Calculator original 12 digit , Photo Paper glossy Per Pkt , Computer Addres Slip - 1x 3 100 sheet , Metallic Binder clips 32 MM , Back rest Per Piece , Paper-A4 Size 75 GSM Per Rim , Stainless Steel Thermosteel Bottle or tea pot 1Litre , Glue Sticks 8gm , Large spiral notebook , Paper Colored Separator , Metallic Binder clips 41 MM , Pencil , Stainless Steel Waste paper basket Per Piece , Jute bag Medium , Writing spiral pad small , Legal Size Paper Per Rim , Metal Scissors , Jute bag pouch carry sanitizer kit , Tissue Paper Box , Metallic Gem Clips of OFICLIP , Gum Tube 30 ml per Piece , Metal Meeting stand , N95 Mask , Attendance Register side cloth 2 Qr. of 144 Pages Per Piece , Paper Tape-2 inches , Steel Clutch Pencils , Wooden Tea Coaster 6 Per Set , Sealing Wax LION 400 gms std Per Piece , CARD BOARD L PAPER folder 34cm H x 26 cm w , Pencil Carbon paper 100 sheets , Jute folder with Flap , Register Dispatch 8 Qr. Per Piece , Paper Color separator , Metal Pencil Sharpener , Wooden White Board 3x5 , Highlighter , Double Sided Self Adhesive Tape - 1.5 inches Foam , All Pin , Metal Pen Pencil holder , Wooden White Board 3x2 , Bottle Sanitizer 50ml , File Board No. 51 Per Piece , Double Sided Self Adhesive Tape - 1inches Foam Per Piece , Pin , Steel Foot ruler , Wooden White Board Duster , Pencil Eraser Non- dust , Register Ruled side cloth Bound-2 Qr 144 Per Piece , Double Sided Self Adhesive Tape Half inchesFoam Per Piece , Index File Per Piece , Eraser Big Size Per Piece , White A4 size Envelope 120 GSM , Steel Stapler , PU Leather Clear ID Card - Holder Per Piece , Metal Pin Remover , white Fluid , Cobra File Laminated Special Cobra File , Cup Plate set of 12 , Office tray Per Piece , Drawing Pins, Gold Tone Thumbtacks 120 Piece , Steel Stapler Pins , Paper Tape-0.5 inchesx72 yds Per Piece , Metal stapler , Paper Cutter , Permanent marker , Water Glass set of 6 , Metal Meeting Name Plate , Paper Color Flags 1 x 3 inches , OHP and CD MARKER PEN , Bond Paper Pkt Executive bond paper 100 GSM , Paper weight , Parker Aster roller pen Stainless Steel with box , Metallic Binder clips 15 MM , Paper Color Flags 0.5x3 inches , Dam Pad , Metal Paper Punching Machine No. 600 Per Piece 8 cm , Note Pad No.55 80 Sheets inPad , White Tag 20 tag per Bundle - Good Quality , Slip 3 x 3 inches 3M , White Board Magnet Duster , Pilot pen V5 or V7 , Uniball pen 157 , White board marker , Reynolds pen 045 , Uniball Impact gel pen 1.0 , A4 paper rim Colour JK , Punch less Folder Executive Lether , Self ink stump Dater , Pin Board 5 X 3 feet , Officer Diary with Lether cover A4 , Orgnizer Dairy A4

Details: Work Of Augmentation Of Water Supply System Of Keolari Town Under Amrut 2.0 survey, Soil Investigation, Design And Construction Of a. Supply, Installation, Testing And Commissioning Of Raw Water Pumping sets Coupled With Motor Including Electrical Control Panel, Cabling All complete. 3 Nos 30.8lps @ 35m Head.25 Hp a. Raw Water Main Pipes: 300 Mm Dia Di K7 Pipe Including Fittings And fixing, Support, Anchor Blocks, Thrust Block All Complete.l-1.1 Km b. basic Units Of 3.0 Mld (24 Hrs Operation) Water Treatment Plant comprising Of Cascade Aerator, Flash Mixer, Clarifloculator, Rapid gravity Filter, Raw Water & Clarified Water Carrying Channel, Inter- connecting Pipes, Valves, Chemical Dosing Facility, Chlorine Dosing facility Including Clear Water Reservoir. construction Of Zonal Elevated Service Reservoir: 9 Nos d. ips: 50 Kl, 2 Nos and di Pipe (k 9) Network For Pumping Main Length-48.45 Km (for proposed & Existing Wtp) f. providing, Laying, Jointing, Testing, Commissioning Of Distribution network Having Length Of Hdpe Pn-6 Pipe 27.15 Km Of Dia 90mm To 200mm From Ohr To Households Including Excavation, Refilling Road cutting/dismantling, Restoration, Providing Valves, Specials And fittings All Complete. g. Clear Water Pumping Sets: Proposed Wtp, Ips-i, Ips-ii & Existing wtp h. house Connection: 3682. Nos cost Of Drawing Electrical Power Line Including The Cost Of transformer For Raw Water Pumping Sets, Water Treatment Plants & sub-station, Including Ht 11 Kv, Lt Panels, Cabling, Posts All Complete as Required In All Installations. provision For Automation And Scada c.

Details: Supply Of Switch Board Cabinet For Lhb Eog Ac Coaches To Rdso Specn.no.rd so/pe/spec/ac/0184-2015 (rev-1). Note: I) Mpcb#s For Water Pumps 1&2, Condenser & Ventilation Fan motors Ratings Shall Be Provided As Per Rdso Ltr.no.el/7.1.108/sbc Dt.01-05-2023. Ii) The Compressors , Heater Circuits Wiring Shall Be Provided With 4 Sq.mm Cable & Suitable Cage Clamp Terminal Blocks For 4sq.mm Cable (block Nos. 239-241, 243-245, 259-261, 263-265, 242 & 262). Rbc & Ebc (s1f160 & S1f 170) Circuit Wiring Shall Be Provided With 6sq.mm Cable And Suitable Cage Clamp Terminal Blocks (in S1 x3) For 6sq.mm Cable. Iii) Mounting Details For Rmpu Switch Panel & Stiffeners Shall Be Provided As Per drawing No. Icf/sk3-7-2-062 Alt- A Or Latest. Iv) 8 Nos Of Crimping Sockets Shall Be Supplied With Discon necting & Earthing Device As Follows. A) For Schaltbau Make D&e Device Crimping Sockets To Drg. No. icf/sk-7-2-166 Alt-w, Type-d10/38, Bend-90 Degree. B) For Salzer Make D&e Device Crimping Sockets T o Item-10 Of Edts-200 (latest). V) Note.no-4 In Rdso Drg.no.rdso/pe/sk/0205-2019 (rev-1) Sheet 2 Of 16 Shall Be Read As #pg29 Suitable End Fitting For Power & Control Cables Shall Be Used#. Vi) Packing In struction: Pi-115 Ver. 3.0

Details: Interior Stickers With Braille Script For Lhb Non Ac Chair Car (108 Seater)., As Per Drawing: Lj64007 Alt B Item No. 1, 5, 6, 8, 9,13 To 15,17,19,20,22 & 25 With Braille Script To Icf/md/spec-253,rev.00, Packing Instruction:pi136 Ver 1.0, Lettering Inside: One Complete S Et Of Lettering Inside Should Be Packed In Cardboard Box. Different Subsets Should Be Made & A List Of Items Should Be Pasted On Each Packet Of Subsets. Letters Packed In Eac H Subset Under Different Headings Are As Under:- Plumbing : Emergency Flush Button, P Ress For Flush, Notice For Bio Toilet Moulding:- Duties Of Coach Attendant, Push, Pull, N O Smoking, Alarm And Penalty Notice, Door Closes Automatically, Safety Message Near Gate, Notice For Luggage Capacity. Lavatory:- Dust Bin, Fire Extinguisher, Soap Dispenser , No Drinking Water, No Waste Into Toilet, Western Style, Press For Flush, Fire Preventio N And Safety, Marking Of Lavatories / Body Side Door, Notice For Lavatories, Drinking W Ater, Unified Notice For Fire Prevention & Safety. Seat & Berth:- Sticker For Seat Number, Berth Numbers, Letter For Chaining Luggage, Notice For Unreserved Coaches. Air Brake: - Reset Emergency Brake, Feed Pipe, Brake Pipe, Closed, Open, Hand Brake Panel : Furnish P Late, Complaint Book. Window & Ceiling: Pull Window Glass Inside, Indication Plate & Stic Ker For Emergency Window, Emergency Openable Window The Cardboard Box Shall Carr Y A Qr Code Having Details As Listed Below : 1 Name Of The Manufacturer 2 Purchase Order Number 3 Purchase Order Date 4 Unique Serial Number ( Or Lot Number For Bulk Items) Of The Manufacturer Or 5 Date O F Manufacture 6 Delivery Challan No. 7 Delivery Challan Dat E The Qr Code Shall Be As Per Iso/iec18004 Model2 And The Data Shall Be Av Ailable As Xml Using The Tags Detailed Above. Incase The Above Details Are Not Available , Or The Qr Codes Are Not Readable, The Supplied Material Is Liable To Be Rejected. [ Warr Anty Period: 30 Months After The Date Of Delivery ] ]

Details: i) Geo-Technical & Hydro- geological Sub Surface Investigation, Surveying, Planning, Designing, Construction & commissioning of atleast. 5.0 meter dia. & required depth Radial Collector well with 250 mm dia & 300 mtr.(approx) long Infiltration Gallery with laying of LCG strainer pipe of minimum 8 mm thick including sub surface dyke to harvest 4.24 MLD raw water with 16 hours designing operation along with Pump House, Access & Pipe carrying Bridge at Subarnarekha along with 01(one) LT Station room for termination of WBSEDCL power source at vicinity of High Bank at Subarnarekha River (Kerwari), protection work at river bank, including construction of Pipe carrying Bridge with necessary Civil, Electrical (according to I.E. rules), Mechanical & all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement and (ii)Laying of raw water rising main from intake well to CWR(D.I./K9 Pipes All types and Class) with all necessary fittings & valves for raw water rising main work, temporary road restoration works for vehicular movement and pillar carrying pipe line and Jack Pushing works for raw and clear water rising main work all complete and (iii)Construction of R.C.C Over Head Reservoirs(OHR) of 1000 cum & 600 cum capacity with 20 m Staging height per approved departmental design, drawing & Specification etc at zone – A & Zone – B including land development , approach road, internal drainage, boundary wall and Sal Bullah Piling etc and pipe line work and connection to the Distribution and inlet line all complete (iv) Surveying , Geo-Technical Investigation, Planning, Designing, Construction & Commissioning of 770 Cum. capacity Clear Water Reservoir with Pumping station, with Construction of weir with minimum 400 cum capacity sedimentation tank and Slow sand filter of area 1000 Sqm minimum, Chlorination treatment unit, ,land development ,approach road, internal drainage, and boundary wall including Electro- Mechanical works at Jhalda and all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement within Jhalda Municipality under AMRUT 2.0 Project.

Details: i) Geo-Technical & Hydro- geological Sub Surface Investigation, Surveying, Planning, Designing, Construction & commissioning of atleast. 6.0 meter dia. & required depth Radial Collector well with 250 mm dia & 300 mtr.(approx) long Infiltration Gallery with laying of LCG strainer pipe of minimum 8 mm thick including sub surface dyke to harvest 4.24 MLD raw water with 16 hours designing operation along with Pump House, Access & Pipe carrying Bridge at Subarnarekha along with 01(one) LT Station room for termination of WBSEDCL power source at vicinity of High Bank at Subarnarekha River (Kerwari), protection work at river bank, including construction of Pipe carrying Bridge with necessary Civil, Electrical (according to I.E. rules), Mechanical & all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement and (ii)Laying of raw water rising main from intake well to CWR(D.I./K9 Pipes All types and Class) with all necessary fittings & valves for raw water rising main work, temporary road restoration works for vehicular movement and pillar carrying pipe line and Jack Pushing works for raw and clear water rising main work all complete and (iii)Construction of R.C.C Over Head Reservoirs(OHR) of 1000 cum & 600 cum capacity with 20 m Staging height per approved departmental design, drawing & Specification etc at zone – A & Zone – B including land development , approach road, internal drainage, boundary wall and Sal Bullah Piling etc and pipe line work and connection to the Distribution and inlet line all complete (iv) Surveying , Geo-Technical Investigation, Planning, Designing, Construction & Commissioning of 770 Cum. capacity Clear Water Reservoir with Pumping station, with Construction of weir, sedimentation tank and Slow sand filter , Chlorination system ,land development ,approach road, internal drainage, and boundary wall including Electro- Mechanical works at Jhalda and all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement within Jhalda Municipality under AMRUT 2.0 Project.

Details: SET OF SEATS FOR L.H.B GS AMRIT BHARAT COACHES. FOLLOW CUSHIONING MATERIAL EITHER PU FOAM TO RDSO SPEC. RDSO/2007/CG-04 REV. 01 OR SILICON FOAM TO RDSO SPEC.RSDO/ 2013/CG-13 REV. 01 WITH FIRE PROPERTIES COMPLIANT TO R21 HL-3 OF EN45545 STANDARD AND U PHOLSTERY TO RDSO SPEC.RDSO/2008/CG-07 REV-NIL WITH AMENDMENT SLIP NO-5 WITH CORRIGEN DUM 1 OF MAY 2015. COLOUR SHADE TO BE FOLLOWED AS PER DESIGN LNO.MD46271 DATED 30.09. 24, as per Drawing: MPLSLSDD VERSION 1, Packing Instruction: ALL PROTRUDING PORTIONS OF SEAT/ BERTH SHOULD BE PROTECTED WITH ENVIRONMENT FRIENDLY PRE MOULDED THERMOCOL CAP OF R EQUISITE STRENGTH OR SILICON RUBBER CAP AS AN ALTERNATE OPTION. EACH INDIVIDUAL SEAT/BE RTH SHOULD BE COVERED WITH BIODEGRADABLE BUBBLE SHEET OF DIAMETER 10MM AND THICKNES S 30 MICRON ALL ROUND. FLAP OF BERTH SHOULD BE OUTSIDE THE BUBBLE SHEET PACKING LEAVIN G SEAT & BERTH MOUNTING UNCOVERED. THEN IT SHOULD BE WRAPPED ALL ROUND IN THICK LAMIN ATED JUTE FABRIC OF SUFFICIENT STRENGTH. THE ASSEMBLY SHOULD BE TIED WITH NYLON STRIPS. I T IS FURTHER WRAPPED WITH BIODEGRADABLE POLYTHENE ALL ROUND TO PREVENT INGRESS OF DU ST/WATER. FOR THE FOLLOWING ITEMS (IF COVERED UNDER S&B SET) THE ITEM-WISE PI (LATEST VER .) WILL BE AS UNDER : 1. CHAIR ANGLES, EXPANDED METAL PARTITION FRAME,SUSPENSION STRAPS, SUPPORTS AND MTG. BKT PI004 2. HARDWARE ITEMS PI019 3. ITEMS LIKE BEARING BKT, CHAIN BKT, C ATCH ARGGT, HINGE BKT AND SLEEVES ETC. PI020 4. LADDERS PI031, LUGGAGE RACKS PI042 A LIST SHOULD BE PASTED ON EACH BOX SHOWING PO NO, PL NO, DESCRIPTION, DRG NO, QTY, FIRM NAME & ADDRESS, DATE OF DISPATCH ETC NOTE : FIRMS HAVE OPTION TO PROVIDE QR CODE . THE ITEM S HELL CARRY A QR CODE ON CARDBOARD BOX NEAR THE MANUFACTURER NAME STICKER CONTAININ G THE DETAILS AS LISTED BELOW: " NAME OF THE MANUFACTURER " PURCHASE ORD ER NUMBER " PURCHASE ORDER DATE " UNIQUE SERIAL NUMBER (OR LOT NUMBE R FOR BULK ITEMS) OF THE MANUFACTURER OR " DATE OF MANUFACTUR E " DELIVERY CHALLAN NO. " DELIVERY CHALLAN DATE THE QR CODE SHALL BE AS PER ISO/IEC18004 MODEL2 AND THE DATA SHALL BE AVAILABLE AS XM L USING THE TAGS DETAILED ABOVE