Directorate General Defence Estates Tender

Removing excavated material 1.50 km but n. exc. 5 Km and depositing where required

M/L Sand filling under floor or in foundation including watering & consolidation as specified.

M/L Continuous brick edging with width equal to the length laid dry as specified.

M/L Boring hole horizontally under ground at required level with trenchless digging machine or manually suitable to pass 50 mm dia MS pipe in the bored hole under the road including passing of cable of suitable size and disposal of spoil to a distance n exc 125 m all as specified and directed by the Engineer in Charge (MS pipe and fitting measured and paid separately).

S.F and laying into horizontal bore hole under the road 50 mm dia MS pipe heavy duty 3.25 mm wall thickness, welded and socketed ends as specified and directed by Engineer in-Charge.

M/L Switch fuse unit metal clad or sheet metal, three phase with neutral link 100Amp , 415 volts with HRC fuses complete as specified

M/L Bus-bar chamber consisting of three phase and neutral aluminum strips of 100 Amp Capacity including connections with thimbles complete as specified

M/L XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100v grade cross-sectional area 25 sqm, 4 core as specified

Earthing complete with galvanised steel earth plate electrode 60x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5m below normal ground level, connected to galvanized earth strip 25 x 3mm by means of both nuts check nuts and washer of galvanised iron or steel including concrete chamber of PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) PCC with fair finish internal surface of concrete chamber will be given 15 mm thick plaster in CM 1:4, funnel with wire guage of (0.68) 8 mess 80 mm thick RCC pit cover 320x 320 mm of RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) re-inforced with Jalli and including necessary charcoal dust and common salt all as per DSR Specifications and specified including provision of earth wire protected by 40mm dia medium grade pipe and watering pipe shall be 20mm dia medium grade including all excavation and earth work in any type of soil and connecting earthing to an earthing test point to main panel board and testing on completion all as specified & directed by Engineer-in-Charge. NOTE : RCC pit cover shall be of pre cast RCC (1:2:4) type-B-1 80mm thick re-inforced with jalli weighing not less than 4 kgs/sqm in lieu of CI cover.

Demolitionof stone slabs and tiles of any description or thickness in floors etc

M/L XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, 4 core and cross sections area 50 sqmmm as specified and directed by Engineer-in-charge

M/L XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, 4 core and cross sections area 95 sqmmm as specified and directed by Engineer-in-charge

Providing casting in position M-30 grade re-inforced cement concrete pole foundation as per manufactures specification, including fixing of J bolts terminal blocks, MCB etc and providing placing 50 mm dia DWC pipe double corrugated with corrugation on outer surface and plain surface in inner side HDPE pipe of suitable bore and suitable length for cable inlet and exit as specified and directed by Engineer-in-charge.

Providing & laying in position ready mix concrete M-7.5 grade machine batched machine mixed design mix concrete placing in position mechanical viberated and finished including addition of ad mixtures in recommended portion as per IS-9103 to accelrate/ retard setting of concrete to improve work ability without tempering strength and durability laid to required slope and chamber in panels as directed in accordance with IS 456-2000 transported to the site of work from approved RMC plant in transit mixers. The minimum cement content shall be as per IS 456:2000 for moderate conditions

Providing & laying in position ready mix concrete M-25 grade machine batched machine mixed design mix concrete placing in position mechanical viberated and finished including addition of ad mixtures in recommended portion as per IS-9103 to accelrate/ retard setting of concrete to improve work ability without tempering strength and durability laid to required slope and chamber in panels as directed in accordance with IS 456-2000 transported to the site of work from approved RMC plant in transit mixers. The minimum cement content shall be as per IS 456:2000 for moderate conditions

S/F Ornamental Decorative Pole made out of cast iron base (HT-625mm) and upper profile with dia 90 mm x 3.2 mm galvanized mild steel pipe (HT-2425mm) pole is primer coated and PU painted not less than 90 micron having service window for incoming and outgoing connections. Pole should be prewired with MCB and conductor ready to install. Pole should be suitable for mounting of 50W LED Post Top fixture Cat. No. Twinkle Lite – LORETTA-3000 mm or equivalent of Philips, Wipro, Bajaj, Havells, LUX MAX, Twinkle, Orient

S/F of Ornamental 45 Watt LED Post Top Luminaire made of die cast aluminium housing duly Powder Coated/ PU painted with clear/frosted diffuser with sturdy four arms MCPCB having high Lumen LED’s are mounted on aluminium heat sinks Twinkle Lite – 539(PT-45) or equivalent make of Philips, Bajaj, Orient, Wipro, Havells, LUX MAX, Twinkle

S/F of ornamental 50 watts LED Post Top luminaries made of aluminum having duly powder coated PU painted with PC / PMMA clear / Frosted diffuser with sturdy triple arm. MCPCB having high luman LED are mounted on aluminum heat sinks. Twinkle Lite – 537(PT-50) or equivalent make of Philips, Bajaj, Orient, Wipro, Havells, LUX MAX, Twinkle

S/F laying, jointing of two run of PVC insulated cable 2.5 sqmm size with copper conductor and connecting from Kiosk box to light fitting as specified and directed by Engineer-in-Charge.

Providing and fixing in floors/ pavements and the like Factory made 60 mm thick cement concrete Prefab Interlocking Coloured Paver Blocks of any Colour, shape and pattern (Malino, Square, Basil, I-Section or any other pattern as approved by Engineer-in-Charge) having Compressing strength of 300 Kg/Cm2 with grey cement and pigment manufactured in joint less moulds on vibration table, of size shape and pattern as approved by Engineer-in-Charge, laid over a base of 30 mm (average) thick Jamuna sand and joints filled with fine sand and finally compaction of bedding sand and blocks laid over it, with vibratory plate compactors, till the top of each paving block is in level with its adjacent blocks complete as per directions of Engineer-in-Charge. APPROVED MAKE: Nimco precast Pvt. Ltd., K.K. , TeraFerma, Koncrete Koncepts Ltd., NTC, NITCO, Unitile, Unistone, Dalal. Contractor to submit procurement vouchers along with the bill. Note :- (i) contrctor to submit tax paid vouchers of paver block obtained from approved manufactures for claim of item in RARs/ Final bill. (ii) Contractor to submit manufacturer certificate for supply of 60 mm thick quality paver block having comprehensive strength of 300 kg/ cm2 for the designated site of work.

Supplying /installation/testing and commissioning feeder pillar outdoor, cubical type, weather proof totally enclosed suitable for 440 V , 3 phase,50 C/s electric supply fabricated out of angle, 40 mx40m x6mm and Ms plain sheet 2 mm thick complete with two coats of spray painting of enamel paint, with a prior coat of primer, comprising of the following . a) Aluminum bus bar TPN , 3 phase, 4 strips-100 Amp. 1set.b) Incoming MCB TPN 63 Amp -1 No. c) OutgoingMCB TPN 32Amps. – 1 No. d) MCB Single phase neutral (SPN) outgoing - 4 Nos. 32 Amps. e) 24 Hrs electronic Timer- 01 no. f) 40 Amp TP Air brake contactor -01 g) Heavy duty godown lock- 02 nos.h) Termination incoming /outgoing cable with suitable size of ferrules and compression gland. i) Hinged door open able on both side with heavy duty locking system-2 no.j) Canopy at Top.k) Legs of suitable length made out of 40 mmx40mmx6 mm angle iron including grouting the legs in 1:2:4 CC.

MS Foundation Bolt etc. with Nut & Washer