Delhi Development Authority Tender

Dismantling the existing feeder pillar and Supplying/replacement of feeder pillar with floor mounted Light control LT feeder pillar cubical type double door of size of 1000 mm x 900mm x 300 mm deep duly compartmentalized and with general arrangement made out of 2mm thick CRCA sheet having hinged gasket cover and screwed knobs with double locking arrangement and rain protection covers 100 mm and supported with of MS angle iron legs and bottom frame of size 40mm x 40mm x 6mm x 1mtr. long grouted with 1:3:6 CC foundation and should be 0.7 mtr. above ground level. Legs should be covered with brick walls, connections, inter connections with suitable size of FRLS PVC insulated copper conductor using thimbles wherever required, painting, numbering including supply and fixing of following accessories complete etc. as required. (a)63 Amps. Four Pole MCB ('C'-Series), 10kA----1 No. (b)16 Amps. SP MCB ('C'-Series), 10 kA------ 6Nos (c) Analogue Timer switch for daily operation and toggle switch for auto/manual --1 No. (d) 32 Amps. AC-3, 3 pole power contactor -----1 No. (e) 30 Ampere 4 way neutral link/connector ------2 Nos. (f) Voltmeter (0-500 Volt) 96mm X 96mm square type with selector switch ---1 No (g) Phase Indicating Lamp Set with fuses ----1 Set (h) Danger notice plate -----1 No (i) AI. Bus Bar 100 amp. 4 strip, 300 mm long with sleeve and nut bolts-----1 Set. (j) Ammeter (0-30Amp) 96mm X 96mm square type ----1No. (k) Lifting hook on the top of panel board and lighting arrangement inside the feeder pillar---- 1 No. (l) 32 Amps. TP MCB ('C' Series), 10KA- 2 Nos.

Supplying, Replacement, testing and commissioning of floor mounted L.T. pump panel cubical type single door of size of 1000 mm x 900mm x 300 mm deep with general arrangement made out of 2mm thick M.S. CRCA sheet having hinged gasket covers and screwed knobs with double locking arrangement and rain protection covers (100 mm), welding of MS angle iron legs and bottom frame of size 35mm x 35mm x 5mm x 1mtr. long grouted with 1:3:6 CC foundation and should be 0.7 mtr. above ground level. Legs should be covered with brick walls, duly 1:4 cement plaster, connections, inter connections with suitable size of FRLS PVC insulated copper conductor using thimbles, ferrules wherever required, painting, numbering, earth studs including supply and fixing of following accessories complete as required. (a) 125 Amps. 4 pole MCCB, 36 K Amp.--1No. b) 3 phase DOL submersible pump starter & C-Curve TP MCB with suitable relay range of 13 to 22 Amp. --- 1 Set. (c) 32 Amps. DP MCB ('C'-Series)------1No. (d) 32A TP & N MCB (C-series)----2 No. (e) Danger notice plate -----1 No (f) Lifting hook on the top of feeder pillar ---1Set. (g) Al. conductor Bus bar of 400mm in length and of size 30x5 mm. (h) Ammeter (0-100Amp) 96mm X 96mm square type ---1 No. (i) Voltmeter (0-500 Volt) 96mm X 96mm square type with selector switch ---1 No. (j) Phase Indicating Lamp Set with fuses ----1 Set

Supplying, Fabrication, replacement and Installation of wire mesh protection frame for existing feeder pillar made out of 8 SWG M.S wire mesh size (75mmX25mm rectangle nominal) of following size with M.S angle iron base frame 35mm X 35mm X 5mm angle iron and with M.S strip support of size 35mm X 5mm in cross and 0.5mtr long legs support of same angle (as per drawing attached), i/c door in front portion, supplying and fitting of go down lock i/c locking arrangement, painting and grouting of angle iron frame with lugs in CC 1:3:6 foundation etc. as approved by Engineer incharge etc. complete as regd. (a) 2 mtr (H) X 1.5 mtr (W) X 1.0 mtr (D)