Public Works Building And NH Department Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Public Works Building And NH Department - PWDBNH Tender
Civil And Construction
Building Construction
Eprocure
Opening Date21 Jan 2022
Closing Date1 Feb 2022
Tender Amount₹ 22,69,59,600
Costs
EMD
₹ 45,39,200Document Cost
₹ 12,500Tender Fee
Refer Documents
Summary
Construction Of Proposed New Assam Legislative Assembly Building
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_PWBNH_24102_1Bid Award Id
ViewTender No
TECH-II/103/2021 ALA_Interior WorksTender Authority
Public Works Building And NH Department ViewPurchaser Address
-Website
http://https://pwdbnh.assam.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :
Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.
447
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : "1:4:8 (1 cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size drived from natural sources).
17.38
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights :
Foundations, footings, bases of columns, etc. for mass concrete
18.04
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights :
Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
184.06
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
6975.32
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
588.6
-
-
Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete.
Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.
In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works upto plinth level
Concrete of M25 grade with minimum cement content of 330 kg/cum
47.31
-
-
Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete.
Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.
In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works above plinth level upto floor V level
Concrete of M25 grade with minimum cement content of 330 kg/cum
4.36
-
-
Providing and laying autoclaved aerated cement blocks masonry with 115 thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar.The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
73.93
-
-
Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
80.04
-
-
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).
Second class teak wood
3.26
-
-
Polishing in high gloss/matt finish melamine matt clear polish on new wood work in required colour/wooden shade texture with following process in the sequence as detailed. 1st the surface to be polished is to be sanded with sand paper 80no./120no. And then sanding with sand paper of 160x180 nos. Applying sealer coat with brush or spray gun which is allowed to dry for 8 to12 hours. on drying of sealer coat wet sanding with emery cloth of finer grating with ample water id done so as to remove excess sealer layer and make the surface further smooth after this wet sanding the surface is applied with special grade melamine filler so as to fill all the small and big holes/grooves etc. filler coat dries in 4 to 6 hr on which again a light wet sanding is done and this surface is allowed to dry for 12 hrs.On this 1st coat of melamine polish is applied using malamine and hardening compound in light proportion using melamine thinner.As far as possible this coat shall be done with compressor pressure air gun. This 1st Coat is allowed to dry for 12 Hrs. On drying the final Melamine polish is applied with compressor pressure gun using melamine and hardener is right proportion. Final coat may be in 1 or 2 layer but care should be taken that it is not overdone.
165.51
-
-
Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.
10 x 160 mm
522
-
-
Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood (50 x 20 mm)
501.8
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
226.92
-
-
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
226.92
-
-
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
1.0 mm thick.
453.84
-
-
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete..
69
-
-
Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm
36
-
-
Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
54
-
-
Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm (both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher
and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.
75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)
390.07
-
-
Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturer’s specifications in superstructure above plinth level up to floor V level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2
1735.06
-
-
Assembly hall seating staircase
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
Hot finished welded type tubes
42327.15
-
-
Assembly hall seating staircase
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete
21489.42
-
-
Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling andfloor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.
7514.2
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.
40mm thick with 20mm nominal size stone aggregate.
917.54
-
-
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
299.57
-
-
Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (For Toilets)
265.33
-
-
Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, 1800mm length (minimum) and 130 mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded polyethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.
917.54
-
-
Providing & fixing in position Phenol bonded Bamboowood in wall skirting with planks of sizes 14mm thick, 1900mm length (minimum) and 85mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The skirting shall be fixed with SS screws & rawl plugs, over underlayment of 4mm thick, expanded polyethylene foam sheets having 40kg/cum density over prepared surface. The bamboowood planks shall have minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.
91.76
-
-
Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:
133.89
-
-
12 mm cement plaster of mix : 1:6 (1 cement : 6 fine sand)
1908.25
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
1908.25
-
-
Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work
1908.25
-
-
Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.
755.61
-
-
(For Glass Partitions)
Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion
Powder coated aluminum (minimum thickness of powder coating 50 micron)
16745.4
-
-
Filling the gap in between aluminum frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width
110.2
-
-
(For Glass Partitions)
Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.
239.22
-
-
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
104.93
-
-
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.
For vertical surface two coats @ 0.70 kg per sqm
134.1
-
-
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.
For horizontal surface one coat @1.10 kg per sqm.
4150
-
-
Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 ?45 MPa and adhesive bond strength Class R3 ?1.5 MPa. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.
For sealing cracks and faulty construction joints, routed out/making U-shape groove size 25x25mm and then primed the area with integral crystalline slurry @0.05kg/running metre and while the surface is tacky filled the groove upto surface with crystalline mortar @1.50kg/running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05kg/running metre per coat.
447
-
-
Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3) : 1996 (Board with BIS certification marks)
138.24
-
-
Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gsm/sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T" at 600mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-charge.
GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum),including factory painted after bending and perforation,and backed with a black Glass fiber acoustical fleece.
609.96
-
-
Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long Dry Wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.
Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/ mK.
24.28
-
-
Designing, providing, installing / fixing skylight consisting of 16mm thick multiwall polycarbonate sheet "Danpalon" or equivalant in approved color (minimum 900mm wide) with standing seam on both sides & double tooth snap on locking system to ensure maximum uplift capability. The panel shall be co-extruded UV protected and antiglare / softlight to prevent glare/sun streak . The cross section of one cell should not be more than 4mmX4mm & weight of single panel shall not be less than 3250 per square metre. The system shall be fitted on purlins with spacing as specified by manufacturer with stainless steel fastener & screws and supported on MS tube framework, complete as per specification, drawing and direction of Engineer in Charge. The rate includes cost of all the operations,labour materials and tests (as applicable) for proper completion of the work except the M.S tubular framework which shall be measured and paid separately (For payment purpose the area of finished polycorbonate sheet fixed in position shall only be measured).
71
-
-
Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.
The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
576.58
-
-
Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
87
-
-
Providing and fixing approved brand and manufacture Stainless Steel 304 grade CYLINDRICAL LOCKS - CLASSIC LOCK. Complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
69
-
-
Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 300 mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
69
-
-
Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
18
-
-
Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
87
-
-
Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
69
-
-
Providing and fixing of ENVIROTECH Make , ENVIRO-WD-1, Doors is one of the best Products to Control Noise and Fulfilling a Demand of a great way in the field of Noise Reduction.
DOOR FRAME: - Door frame made out of good quality hard wood , section size – 100 mm x 110 mm fitted with ‘D’ type rubber gasket to block noise leakage from gap .
DOOR SHUTTER:-Providing and fixing acoustic door with minimum 60 mm thickness along with fire rating and smoke Intumescent seal strip of size 10mm x 4mm for 120 minutes fire rated and STC 37dB Tested by National Physical Laboratory, Pusa Road New Delhi and having infill of 50mm thick resin bonded glasswool of 48 kg/cum density sandwiched by two 10mm thick approved quality marine grade ply and finished with 1 mm thick laminate of approved make, shade and colour and design on both sides. Further edges of shutter shall be provided with 6mm thick teak wood beading using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with approved melamine polish etc. The ply shall be resistant to vermin, mould growth, minor impact, abrasion and short term water attack and with a smooth surface suitable to receive most forms of decoration. The door shall have acoustic seal in door rebates and drop dead seal at the bottom of the door including ironmongeries.
HARDWARE :-The door assembly shall be fixed to the door frame with heavy duty hardware i.e. Geze/ Assa abloy/Dorma Make or equivalent make SS Hinge Size: 4”x 3”x 3mm , 600 mm SS door handle , SS Tower bolt ,Door closer , Panic Bar ,Panic trim etc.
ACOUSTIC INSULATION: The Panels filled with Acoustic material Rock wool confirming to IS-8183 of 96 kg/m3 density, very good noise absorber for high, mid & low frequencies along with, 6 MM thick anti donning layer having Thermal Conductivity 0.037 @ 20 C as per EN ISO 8497 (DIN 52613) and 2 mm thick Sound Damping layer MTS 05-303 to achieve higher Sound STC as per site condition.
10.08
-
-
Providing and fixing approved brand and manufacture SS 304 grade Top & Bottom Patch fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
26
-
-
Providing and fixing approved brand and manufacture SS 304 grade H type 900mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
22
-
-
Providing and fixing approved brand and manufacture SS 304 grade Glass to Glass Lock Round type with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
13
-
-
Providing and fixing approved brand and manufacture SS 304 grade Floor spring (weight approx 100-120kgs) fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.
13
-
-
Automatic Sliding Door- Frameless
Providing and fixing Automatic Sliding door operator, Make: dormakaba ES 200 Easy - 4.15 Mtrs Bi-parting Sliding System, compliant with European standards and produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the UVV and the VDE regulations. TÜV design tested, tested according to the low voltage guidelines, production according to ISO 9001:2000 certification, fulfils DIN18650 Standards for Pedestrian Safety, TUV Design Tested for Durability of 1 Million Cycles, for frameless glass door application, modular design including internal cover. and with 12 mm clear toughened glass for 2 Nos sliding door panel, Operator to be mounted on MS-Box Section/ Equalant. Operator Finish should be Silver Anodised E6/C0, with operator dimensions Maximum (H x D) : 100 x 180 mm and of length as required to suit the opening size given below. The track profile should be separate from the main profile for enabling reduction in vibration insulation and easy maintainence. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Class of protection IP 20. Activators- dormakaba Nemo Motion + Nemo Dual ( Safety& Motion), EM Lock - Fail Safe and 5 Position Program Switch.The system shall have constant power supply 230V+ 5%, 50Hz, AC . The requirement in total is as mentioned below:
Clear Passage Width = 700 - 2000 mm
Max Clear Passage Height = 3000 mm
Max Panel Weight Double Sliding = 2 x 100 Kgs.
Max Panel Weight Single Sliding = 1 x 120 Kgs
2
-
-
Supplying, fitting and fixing of full height partition wall partly made with 10mm thick toughened glass with wooden frame work and partly made of secondary seasoned hard wood as approved, out of 60mm X 150mm section both horizontal and vertical at edges including covering the above frame with BWR plywood with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C including polish and melamine finish. Finished Surface on plywood to be paied for under reference item
57
-
-
Supplying, fitting and fixing full height wooden partition made of secondary seasoned hard wood as approved, out of 60mm X 50mm section both horizontal and vertical @ 600 c/c including covering the above frame (Primary Surface) with 12mm BWR ply wood on both side with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C including polish and melamine finish. Finishing surface paid separately
50
-
-
Supplying, fitting and fixing full height wooden partition made of secondary seasoned hard wood as approved, out of 60mm X 50mm section both horizontal and vertical @ 600 c/c including covering the above frame (Primary Surface) with 6mm BWR ply wood on both side with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C including polish and melamine finish. Finishing surface paid separately
50
-
-
Supplying, fitting and fixing full height wooden partition made of seasoned hard wood as approved by EIC out of 100mm X 50mm wooden section timber both horizental and vertical and necessary M.S. supports using horizontal and vertcal and necessary welding (Angle, joinsts, tees, channels, etc.) including covering the above frame (Primary Surface) with 6mm BWR ply wood on both side with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C including polish and melamine finish. Finishing surface and M.S. work to be paid separately.
50
-
-
Supplying, fitting and fixing full height wooden partition made of seasoned hard wood as approved by EIC out of 100mm X 50mm wooden section timber both horizental and vertical and necessary M.S. supports using horizontal and vertcal and necessary welding (Angle, joinsts, tees, channels, etc.) including covering the above frame (Primary Surface) with 12mm BWR ply wood on both side with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C including polish and melamine finish. Finishing surface and M.S. work to be paid separately.
50
-
-
Supplying, fitting and fixing full height wooden partition made of seasoned hard wood as approved by EIC out of 100mm X 50mm wooden section timber both horizental and vertical and necessary M.S. supports using horizontal and vertcal and necessary welding (Angle, joinsts, tees, channels, etc.) including covering the above frame (Primary Surface) with 12mm ply wood on one side and other side 6mm ply wood with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C including polish and melamine finish. Finishing surface and M.S. work to be paid separately.
50
-
-
Finishing on Primary Surface with decorative veneer 4mm thick. (Both side measure separately )
100
-
-
Providing and installation of acoustic wall panelling consisting of Stretch NRC by using FR Grade NRC fabric of size 1700mm width, shall be stretched by using wooden base 10mm thick, rigid vinyl Stretch Tracks half wrap/ full wrap 25mm and Midseam 25mm , strand, synth PF with requisite accessories and tools. Woodenbase 10mm is first installed on the wall along the marking lines with metal fasteners at 300mm centers . tracks to be installed on wooden base, by using Base tape (by removing the protective cover) for a true and continuous secure grip, and heavy-duty fasteners at 15mm centers on one/both sides of Stretch Tracks. Strand square edge magnesite bonded wood fiber panels of size 600x1200x15mm having density 400kg/m3, weight 4-8kg which is fixed to wall. Synth PF 10x10mm thick adhered on strand panel by using Stick 7 adhesive. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stuck on the Align Tape (by removing the protective cover) at the same time as being stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note - minimum 50mm additional fabric is required for tucking hence maximum module width would be 1600mm.
332.38
-
-
Providing and Installation of acoustical wall panelling fabric finish hardened square edge, FR grade fabric (colour as approved by Egnineer in charge) wrapped soft fibre core (glass fibre) panel of size 600x2100x25mm having density 100-120Kgs/ m3, weight 3.0kg/m2 NRC up to 0.9 installed by using impaling clip. Impaling clips are attached directly to the wall/frame work with the points extending outward . Then panels shall positioned and pressed into place .
142.45
-
-
Supply and Installation of two layers of 20mm thick cement bonded particle board (made of 62% cement and 28% wood having a density of 1250 kg/3, compressive strength of 15N/m2 having capacity to hold screws and nails)with a sandwich of 3 mm thick visco elastic polymer sheets having a surface density of minimum 4.88kg/m2. UV resistant, resistance to mold , water and heat, and shall be 100% recyclable and has noise isolating properties. Visco elastic polymer sheets are fixed to cement bonded particle board by using adhesive recommended by manufacturer. Sandwiched cement bonded particle board is fixed rigidly to metal frame work by using suitable fastners.Hollow sections of metal frame work shall be filled with sand to reduce creaking noise while climbing /getting down from steps. Note - if panels should be fixed firmly to metal structure without any air gaps and are covered with carpet with 10 mm foam underlay
950
-
-
Carpet flooring
Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm, and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation, with ten year replacement guarantee. The carpet should have permanent static control & should be fixed with powder coated aluminum angles as per detail.
Assembly Hall
418.68
-
-
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades including tile fixing chemical adhesive grouting the joint with Epoxy grout etc., complete.
Full Body Vitrified floor tile 800x800 mm
50.36
-
-
Providing and fixing 18mm thick Granite stone work for wall lining upto 10 m height in cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white cement mortor with an admixture of pigment to match the granite shade complete as per direction of Engineer-in-charge.
92.04
-
-
Providing & fixing 150mm wide Chicken wire mesh on joints of RCC & Brick work before plastering complete in the direction of Engineer-in-charge.
190.83
-
-
Providing and fixing 50 micron thick Etching strips (film) over glass Non-fade, self adhesive,easy to cut and trim to size and easy to install, of approved make and manufacturer, fixed as per manufacturer's specifications and as specified in Arch. drawing, all complete in all respects as per direction of the Engineer-in-charge.
111
-
-
Supply and Fixing Modern semi-concealed Wood Tile Ceiling consisting of wood veneer tiles mounted on a 24 mm slotted tee bar system. The tilesshould be 16mm thick FR treated MDF (BS Class I) or a 16mm standard MDF (FR BS Class III) core veneered with 0.6mm thick slip/book matched veneer on the visible side. A 0.6mm compensating veneer should be adhered to the reverse of the tile. SUSPENSION should Consists of pre-punched main tee sections installed in a grid by means of inserting cross tees designed to be used with the size of tile selected. Maximum distance of rapid hangers fixing points on the main tee is 1200 mm. Main tees and cross tees will be finished standard baked enamel finish in colour. An acoustic non-woven textile of thickness 0.2mm shall be glued on reverse tile side. ( Make Hunter Douglas (Luxalon), Armstrong or Equivalent)
155.35
-
-
Providing and Fixing of 16.5mm thick Micro perforated wooden acoustic panel of size - 600mm x 1200mm / 600mm x 2400mm , front side perforation diameter will be 0.5mm – 0.7mm at a distance of 02 mm c/c and backside 10mm dia. as per acoustic design / Architects approval, The micro perforated wooden acoustic panels to be backed with black acoustic fleece. All joints of panel shall have dowel connection to avoid any sagging /unevenness. The wooden acoustic panels to be fixed on specially designed Powder Coated ‘C’ Channel supported from RCC slab with steel wire / threaded rod. The micro perforated top sheet will be of 0.5mm thick Mica laminate in desired shade as per Engineer In charge / Architect’s approval. The top cavity of ‘C’ channel grid shall be filled with 25mm thick Acoustic pillow to achieve the 1.0 NRC value. All makes and models of all items/samples should be approved by the engineer-in-charge / consultant prior to the installation.
248.85
-
-
Providing and fixing U Baffle Aluminium panel ceiling (M/s Hunter Douglas or Equivalent) consisting of Wood finish panel size 30 mm width X 100mm deep using 0.6mm thick, panel length upto 4 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming characteristics. Panels shall be clipped to a baked enamelled Aluminium carrier of 30 mm wide x 47 mm high x 0.5 mm thick, Black Colour coated, one leg of the carriers with cut outs to hold the panels in a module of 150 mm. Panel carrier shall be suspended by means of threaded rod at a distance of 1.8 mtr c/c. Aluminium panels shall be chromatised for maximum bond between metal and paint enamelled twice under high temperature, Exposed side with a full primer and finish coat on a Continuous Paint Line. Ceiling area above U Baffle to be painted in black colour before fixing this system (Cost of black paint shall be paid separately).
167.21
-
-
Add extra over any glass surface for forming designed Plane / fosted etching on glass surface by etching or other cutting tools as may be necessary and completely finishing surface, complete as shown on drawing and director by E.I.C.
75
-
-
Add extra over any glass surface for forming designed Colour etching on glass surface by etching or other cutting tools as may be necessary and completely finishing surface, complete as shown on drawing and director by E.I.C.
75
-
-
Add extra over any glass surface for forming designed Deep etching / two-tone frosting / crystal etching on glass surface by etching or other cutting tools as may be necessary and completely finishing surface, complete as shown on drawing and director by E.I.C.
75
-
-
Finishing on Primary Surface with Partly 6mm thick toughened sand blaested glass and partly 6 mm thick toughened clear glass, fixed the glass with S.S. studs.
32
-
-
Finishing on Primary Surface with 6 mm thick toughened mirror panelling, fixed the mirror on the primary surface with S.S. studs
116
-
-
SPECIALISED MOULDING FOR CARPETTED WALL : Supplying,fabricating and fixing in position wooden edge moulding of carpets at joints,made of 18mm X 12mm teak wood fillets of 30 X 12mm ,covered with a teak wood planks duly wrought and fixed on walls with ss screws and wall plug @ 300 c/c stoutly hold in position complete all as shown on drawing and as directed by Engr.-in-charge / Architect .
390
-
-
Supplying and fixing polished copper plates fixed on wooden base with appropriate patch or fastener all as shown on drawings and as directed by Engr.-in-charge for 2 mm thick copper plates
25
-
-
False ceiling Finishing surface with 6 mm thick toughened glass fixed on the primary surface with S.S. studs Complete with as shown on drawing and as directed by Engineer-in-charge/ Architect.
45
-
-
Supplying and fixing approved quality Duette Architella blinds (Opavue) made of hexagonal pleated Non-woven Polyster fabric, honey comb design and to be fixed built-in Receiver Motor for movement of blinds/curtain all complete as per drawing and direction of Archiotect and manufacturer specification. Approved make. Hunter Doglous or its similar equivalent. (Motor to be paid in separate item.)
221.32
-
-
Supplying and fixing approved quality Duette Architella blinds (Semi Opavue) made of hexagonal pleated Non-woven Polyster fabric, honey comb design and to be fixed built-in Receiver Motor for movement of blinds/curtain all complete as per drawing and direction of Archiotect and manufacturer specification. Approved make. Hunter Doglous or its similar equivalent. (Motor to be paid in separate item.)
776.8
-
-
Supplying and fixing approved quality roller blinds (Optima Screen) made of 0.5mm thick polyster fabric (Wt. 270 - 310g./Sqm. All complete as per drawing and direction of Engineer-in-charge for following types of roller blinds. Approved manufacturer M/s. Hunter Doglas or similar equivalent.
187.79
-
-
Fitting & fixing, chamfering finishing & polishing up to the size of 35mm granite edge groove in all granite of staircase trade etc. and making good to the damages including cleaning etc. completed as directed and specified. (only extra over labour )
4472.7
-
-
Fitting & fixing, making , fixing, finishing & polishing of 75mm nosing granite patti . In staircase tread making good to the damages including cleaning etc completed as directed and specified. (only extra over labour )
3220.5
-
-
Extra Over For Tiles Flooring Making ,Filing & Finishing of 3 mm x 3 mm Spacer Groove of Epoxy Grouting In All Area Flooring & Dadoing . making good to the damages including cleaning etc completed as directed and specified.
1025.87
-
-
Extra over for providing , making & fixing of ply boxing. In all paneling area including supplying all materials, tools, tackles, labours etc. complete as per direction of E.I.C.
9367.9
-
-
Ply paneling work L Corner band including preparing the surface including supplying all materials, tools, tackles, labours etc. complete as per direction of E.I.C.
2126.68
-
-
Ply paneling work 75mm pelmet including preparing the surface including supplying all materials, tools, tackles, labours etc. complete as per direction of E.I.C.
1500
-
-
Extra over for ceiling height. In all ceiling area by additional L Patti support material & labour.
4172.14
-
-
French polishing and melamine finish to wood & Veneer work up To 1'' To 4" per edge including preparing the surface including supplying all materials, tools, tackles, labours etc. complete as per direction of E.I.C.
10540
-
-
Zink polishing and melamine finish to wood work including preparing the surface including supplying all materials, tools, tackles, labours etc. complete as per direction of E.I.C. per edge up to 50mm
2000
-
-
Providing & fixing suspended gypsum board false ceiling ( vertically 100mm Coffer), which includes G.I. perimeter channels of size 0.55mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling screw fixed to brick wall/partition with the help of nylon sleeves and screws at 600mm c/c. Then suspending G.I. intermidiate channels of size 45mm X 0.9mm thick with 2 flanges of 15mm each from the soffit at 1220mm c/c with ceiling angle fixed to soffit of 0.55mm thickness having knurled verb of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips at 457mm centers, 12.5mm tapered edge gypsum plain board ( conforming to IS: 2095 - part II ) is then screw fixed to ceiling section, boards are to be jointed and finished with jointing compound,paper tape and two coats of Drywall Top Coat.
2055
-
-
Providing & fixing suspended 12 mm thick BWR commercial plywood false ceiling (horizontally), which includesmade with approved hardwood, size of bottom is 50mm X 35mm sections, plasing @ 600/400 c/c both horizental and vertical fixed with rawal plage on the Slab or any space that needs including covering the above frame (Primary Surface) with 12mm BWR plywood with necessary edge finish as approved all complete as per drawing and direction of Architect/E.I.C
350
-
-
Providing Making & Finishing of 175mm Wooden AC. Round Grill in Assembly area as directed by the Department.
89
-
-
Providing, installation and dismantling after workdone of scaffolding at the tripple height open area of avg. 25.0m height of central Assembly area with MS tubular pipes as directed by the Department.
200
-
-
Providing, making & finishing of Round Wooden Design Panal of 600mm diameter in Assembly as directed by the Department.
3
-
-
Providing, making & finishing of Round Wooden Design Panal of 400mm diameter in Assembly as directed by the Department.
8
-
-
Providing, making and finishing of 150mm Tapered Moulding in Assembly as directed by the Department.
50
-
-
Providing Making & Finishing of 100mm Wooden Moulding railing tops in Assembly Round Partition as directed by the Department.
300
-
-
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
17
-
-
Providing and fixing White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
17
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink with drain board 510x1040 mm, bowl depth 200mm. as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :
3
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
17
-
-
Providing and fixing Semi rigid 40 mm dia. P.V.C. Waste pipe for sink or wash basin including P.V.C. waste fittings complete.
3
-
-
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
17
-
-
Providing and fixing C.P. brass toilet paper holder :
17
-
-
Providing and fixing C.P. brass 15 mm nominal bore angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
96
-
-
Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.
99
-
-
Providing and laying 1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size ) in position cement concrete of specified grade excluding the cost of centring and shuttering. All work up to plinth.
1
-
-
Providing and fixing PN - 16 Pipe, 25mm OD (SDR-7.4) 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on walls
150
-
-
Providing and fixing PN - 16 Pipe, 32mm OD (SDR-7.4) 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on walls
65
-
-
Providing and fixing PN - 16 Pipe, 25mm OD (SDR-7.4) 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
410
-
-
Providing and fixing PN - 16 Pipe, 32mm OD (SDR-7.4) 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
20
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil
42
-
-
Excavating trenches of required width for Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia. in all kinds of soil including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m.
110
-
-
Extra for excavating trenches for Pipes, cables etc, exceeding 80mm dia but not exceeding 300mm dia in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth upto 1.5 metre).
45
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
12.6
-
-
Providing, laying and jointing 150 mm diameter glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
30
-
-
Providing, laying and jointing 200 mm diameter glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
70
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. For 150 mm diameter
20
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. For 200 mm diameter
50
-
-
Providing and fixing 180x150 mm size P type square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
10
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
6
-
-
Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
2
-
-
Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
2
-
-
Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1
-
-
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
18
-
-
Supplying, installation, testing and comm1ss10ning of STP/ETP of appropriate technology including civil works (except plant room), tertiary treatment etc. for the building / campus
50
-
-
Providing and fixing 15mm C.P brass Sink Mixer for kitchen sink of Parryware Model. No.T3950A1 with swinging spout complete. Including cutting and making good the walls wherever required .
3
-
-
Providing, fitting and fixing chrome plated (CP) twin robe hook of Parryware modal T6007A1 complete as directed and specified.
17
-
-
Providing and fixing 15mm C.P. copper connecting pipe 450mm long of Parryware modal T991299 with C.P. brass nuts, washers complete in all respects.
96
-
-
Providing and fixing health faucet with 1 m long of Parryware modal T9807A1 flexible tube and wall hook including all fittings.
17
-
-
Providing and fixing liquid soap dispenser including all fittings complete.Make Jaquar Model-AKP-35735P or equivalent.
17
-
-
Providing and fixing vertical storage type hot water heater Capacity 25 Litres fixed to wall with anchor bolts & nuts, 15mm CP brass angle stop cock and 15mm CP brass non-return valve complete including making connections with 15mm dia CP connecting pipes on inlet and outlet, suitable length of power cable and 15 amps plug (Venus or approved equivalent).
20
-
-
Providing and fixing 110 mm OD SWR uPVC pipes (Type-B) confirming to IS 13592 : 1992 complete with all fittings e.g. plain or door bends, junctions, cowls, offsets, access pieces etc. jointing with rubber rings and solvent cement including fixing the pipes on wall face with galvanized iron holder bat clamps or suspended below ceiling with galvanized iron hangers/supports and fasteners all as approved by the engineer in charge including Cutting holes in walls, floors excavation, refilling and disposal of surplus earth wherever required and making good . The rates shall be inclusive of painting of all supports and clamps with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.(Sample of holder bat clamps,hangers / supports to be approved by the Engineer-in-Charge.)
175
-
-
Providing and fixing 40 mm OD uPVC agricultural pipes conforming to IS:4985 (6 kg/sqcm) including all fittings, e.g. couplings, tees, bends, reducers and screwed adoptors jointing with solvent cement joint as per manufacturers' recommendations. [for Waste Connections Pipes]
65
-
-
Providing and fixing 50 mm OD uPVC agricultural pipes conforming to IS:4985 (6 kg/sqcm) including all fittings, e.g. couplings, tees, bends, reducers and screwed adoptors jointing with solvent cement joint as per manufacturers' recommendations. [for Waste Connections Pipes]
15
-
-
Providing and fixing 63 mm OD uPVC agricultural pipes conforming to IS:4985 (6 kg/sqcm) including all fittings, e.g. couplings, tees, bends, reducers and screwed adoptors jointing with solvent cement joint as per manufacturers' recommendations. [for Waste Connections Pipes]
15
-
-
Providing and fixing 110 mm inlet and 110 mm outlet. uPVC P-Trap with extension piece including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 hand stone ballast 20 MM nominal size) the inlet from floor level to trap rim to be grouted and cemented neat manner including cutting and making good the floor & wall wherever requiredcomplete in all respects
20
-
-
Providing and fixing in position 125x125 mm stainless steel grating for floor trap/floor drain including fix to floor with cement mortar.
20
-
-
Providing and fixing Thermoflex or Kaiflex thermal insulation tubing For 25 mm OD Pipe a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes)
150
-
-
Providing and fixing 20 mm nominal bore forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects.
37
-
-
Supplying fitting & fixing as per specification drawing & direction Cast iron soil pipe/sand cast iron pipes with specials I.S. 3989 of 1970 and 1729/1964 with bobbin nails, M.S. Clamp/hanger, Ancher fastner, nut and bolt with fittings that is Door Bend, Plain Bend, Trap 'P' or 'S' door junction, plain junction, hand hole piece, cowl, connector, off-set, double junction with or without door, lead joint with gasket, painting two or more coats inside and outside, cutting in wall, floor, ceiling and repairing the same (concrete mix 1:2:4) complete in all respect.(Payment will be made on the centre line measurements of the total pipe line including all specials/fittings. No separate payment will be for accessories, specials fittings).75mm dia. I.S. 1729-1964(Used for A.S.P and waste pipe).
210
-
-
Supplying, fitting & fixing as per specification drawing & direction C.P./S.S. cockroach trap with or without hole grating fixed with white cement as per instruction complete in all respects.
50
-
-
Supplying, fitting & fixing chlorinated polyvinyl chloried (CPVG) pipes 15mm dia., having thermal stability for hot and cold water supply including all CPVC brass threaded fittings including jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of all pipe line including jointing complete in all respects. (For Flush water line) (above work for U.G. above ground concealed in wall and floor hanging on ceiling including M.S. clamping etc. as per drawing and direction).
350
-
-
Supplying, fitting & fixing chlorinated polyvinyl chloried (CPVG) pipes 20mm dia., having thermal stability for hot and cold water supply including all CPVC brass threaded fittings including jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of all pipe line including jointing complete in all respects. (For Flush water line) (above work for U.G. above ground concealed in wall and floor hanging on ceiling including M.S. clamping etc. as per drawing and direction).
117.49
-
-
Supplying, fitting & fixing chlorinated polyvinyl chloried (CPVG) pipes 25mm dia., having thermal stability for hot and cold water supply including all CPVC brass threaded fittings including jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of all pipe line including jointing complete in all respects. (For Flush water line) (above work for U.G. above ground concealed in wall and floor hanging on ceiling including M.S. clamping etc. as per drawing and direction).
170
-
-
Supplying, fitting & fixing chlorinated polyvinyl chloried (CPVG) pipes 32mm dia., having thermal stability for hot and cold water supply including all CPVC brass threaded fittings including jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of all pipe line including jointing complete in all respects. (For Flush water line) (above work for U.G. above ground concealed in wall and floor hanging on ceiling including M.S. clamping etc. as per drawing and direction).
45
-
-
Supplying, fitting & fixing chlorinated polyvinyl chloried (CPVG) pipes 40mm dia., having thermal stability for hot and cold water supply including all CPVC brass threaded fittings including jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of all pipe line including jointing complete in all respects. (For Flush water line) (above work for U.G. above ground concealed in wall and floor hanging on ceiling including M.S. clamping etc. as per drawing and direction).
15
-
-
Supplying, fitting & fixing G.I. Pipe 'TATA' make 32mm dia.(M) class with all necessary accessories, specials viz. socket, elbow, bend, tee, reducer, nipple, flange, union, short piece etc. fitted with holder bat clamp, including cutting pipes making threads, concealed in wall and floor and repairing the same with two or more coats of painting, testing (by pressure machine) as per I.S. two times etc. complete in all respects. (For cold and hot water line).(Payment will be made on the centre line measurement of the total pipe line including all specials/fittings. No separate payment will be for accessories, specials/fittings)
75
-
-
Supplying, fitting & fixing G.I. Pipe 'TATA' make 40mm dia.(M) class with all necessary accessories, specials viz. socket, elbow, bend, tee, reducer, nipple, flange, union, short piece etc. fitted with holder bat clamp, including cutting pipes making threads, concealed in wall and floor and repairing the same with two or more coats of painting, testing (by pressure machine) as per I.S. two times etc. complete in all respects. (For cold and hot water line).(Payment will be made on the centre line measurement of the total pipe line including all specials/fittings. No separate payment will be for accessories, specials/fittings)
100
-
-
Supplying, fitting & fixing G.I. Pipe 'TATA' make 25mm dia.(M) class with all necessary accessories, specials viz. socket, elbow, bend, tee, reducer, nipple, flange, union, short piece etc. fitted with holder bat clamp, including cutting pipes making threads, concealed in wall and floor and repairing the same with two or more coats of painting, testing (by pressure machine) as per I.S. two times etc. complete in all respects. (For cold and hot water line).(Payment will be made on the centre line measurement of the total pipe line including all specials/fittings. No separate payment will be for accessories, specials/fittings)
250
-
-
Supplying, fitting & fixing G.I. Pipe 'TATA' make 20mm dia.(M) class with all necessary accessories, specials viz. socket, elbow, bend, tee, reducer, nipple, flange, union, short piece etc. fitted with holder bat clamp, including cutting pipes making threads, concealed in wall and floor and repairing the same with two or more coats of painting, testing (by pressure machine) as per I.S. two times etc. complete in all respects. (For cold and hot water line).(Payment will be made on the centre line measurement of the total pipe line including all specials/fittings. No separate payment will be for accessories, specials/fittings)
350
-
-
Supplying, fitting & fixing G.I. Pipe 'TATA' make 15mm dia.(M) class with all necessary accessories, specials viz. socket, elbow, bend, tee, reducer, nipple, flange, union, short piece etc. fitted with holder bat clamp, including cutting pipes making threads, concealed in wall and floor and repairing the same with two or more coats of painting, testing (by pressure machine) as per I.S. two times etc. complete in all respects. (For cold and hot water line).(Payment will be made on the centre line measurement of the total pipe line including all specials/fittings. No separate payment will be for accessories, specials/fittings)
350
-
-
Supplying, fitting & fixing 32mm dia. peet's /Gate Valve fullway Gunmetal standard pattern best quality of approved make bearing I.S.I. marking (with G.I. pipes & fittings).(Tested to 21 kg./Sq.cm. (leader brand).
10
-
-
Supplying, fitting & fixing 40mm dia. peet's /Gate Valve fullway Gunmetal standard pattern best quality of approved make bearing I.S.I. marking (with G.I. pipes & fittings).(Tested to 21 kg./Sq.cm. (leader brand).
5
-
-
Supplying, fitting & fixing 50mm dia. peet's /Gate Valve fullway Gunmetal standard pattern best quality of approved make bearing I.S.I. marking (with G.I. pipes & fittings).(Tested to 21 kg./Sq.cm. (leader brand).
2
-
-
Supplying, fitting & fixing 15mm dia. peet's /Gate Valve fullway Gunmetal standard pattern best quality of approved make bearing I.S.I. marking (with G.I. pipes & fittings).(Tested to 21 kg./Sq.cm. (leader brand).
2
-
-
Supplying, fitting & fixing wrought iron 20mm dia. 10mm thick flange of approved quality with rubber washers, nut and bolt as per standard joints complete in all respects.
25
-
-
Supplying, fitting & fixing wrought iron 25mm dia. 10mm thick flange of approved quality with rubber washers, nut and bolt as per standard joints complete in all respects.
20
-
-
Supplying, fitting & fixing wrought iron 32mm dia. 10mm thick flange of approved quality with rubber washers, nut and bolt as per standard joints complete in all respects.
16
-
-
Supplying, fitting & fixing wrought iron 40mm dia. 10mm thick flange of approved quality with rubber washers, nut and bolt as per standard joints complete in all respects.
12
-
-
Supplying, fitting & fixing wrought iron 50mm dia. 10mm thick flange of approved quality with rubber washers, nut and bolt as per standard joints complete in all respects.
10
-
-
Supplying, fitting & fixing as per specification drawing and direction 20mm dia. pressure reducing valve (Leader brand) approved type I.S.I. marked having by-pass arrangement with 3 Nos. gate valve (Gun metal I.S.I. marked) necessary pressure guage at inlet and outlet complete in all respect (holes pressure to a maximum of 16 Kg. and out let pressure 0.5 to 7 kg.)
36
-
-
Supplying, fitting & fixing as per specification drawing and direction 25mm dia. pressure reducing valve (Leader brand) approved type I.S.I. marked having by-pass arrangement with 3 Nos. gate valve (Gun metal I.S.I. marked) necessary pressure guage at inlet and outlet complete in all respect (holes pressure to a maximum of 16 Kg. and out let pressure 0.5 to 7 kg.)
5
-
-
Supplying, fitting & fixing as per specification drawing and direction 32mm dia. pressure reducing valve (Leader brand) approved type I.S.I. marked having by-pass arrangement with 3 Nos. gate valve (Gun metal I.S.I. marked) necessary pressure guage at inlet and outlet complete in all respect (holes pressure to a maximum of 16 Kg. and out let pressure 0.5 to 7 kg.)
8
-
-
Supplying, fitting & fixing as per specification drawing and direction 40mm dia. pressure reducing valve (Leader brand) approved type I.S.I. marked having by-pass arrangement with 3 Nos. gate valve (Gun metal I.S.I. marked) necessary pressure guage at inlet and outlet complete in all respect (holes pressure to a maximum of 16 Kg. and out let pressure 0.5 to 7 kg.)
4
-
-
Providing & fixing thermal insulation in 15mm dia. Pipe (9mm thick insulation)hot water pipe line a polyolafin foam of closed cells structure having thermal conductivity of 0.036 w/M.K. at an average tempenature of 30 C°. The density of materials shall be 30 ± 5 Kg./m³ capable to operate in the range of -80° C to + 95° C fire propogation material shall be self extinguishing and class-I certified as per BS 476 part 7. Material shall be CFL free combustion it should not limit HGN. No + No2 and So1 + H25 gases, smoke generated should be lighter than air and white in colour so as to allow easy exit passage in case of fire including all accessories e.g. adhesive and ....................... joint complete as per specification. All joints portion with adhesive and cotton ......
350
-
-
Providing & fixing thermal insulation in 20mm dia. Pipe (9mm thick insulation)hot water pipe line a polyolafin foam of closed cells structure having thermal conductivity of 0.036 w/M.K. at an average tempenature of 30 C°. The density of materials shall be 30 ± 5 Kg./m³ capable to operate in the range of -80° C to + 95° C fire propogation material shall be self extinguishing and class-I certified as per BS 476 part 7. Material shall be CFL free combustion it should not limit HGN. No + No2 and So1 + H25 gases, smoke generated should be lighter than air and white in colour so as to allow easy exit passage in case of fire including all accessories e.g. adhesive and ....................... joint complete as per specification. All joints portion with adhesive and cotton ......
375
-
-
Providing & fixing thermal insulation in 25mm dia. Pipe (9mm thick insulation)hot water pipe line a polyolafin foam of closed cells structure having thermal conductivity of 0.036 w/M.K. at an average tempenature of 30 C°. The density of materials shall be 30 ± 5 Kg./m³ capable to operate in the range of -80° C to + 95° C fire propogation material shall be self extinguishing and class-I certified as per BS 476 part 7. Material shall be CFL free combustion it should not limit HGN. No + No2 and So1 + H25 gases, smoke generated should be lighter than air and white in colour so as to allow easy exit passage in case of fire including all accessories e.g. adhesive and ....................... joint complete as per specification. All joints portion with adhesive and cotton ......
75
-
-
Providing & fixing thermal insulation in 32mm dia. Pipe (9mm thick insulation)hot water pipe line a polyolafin foam of closed cells structure having thermal conductivity of 0.036 w/M.K. at an average tempenature of 30 C°. The density of materials shall be 30 ± 5 Kg./m³ capable to operate in the range of -80° C to + 95° C fire propogation material shall be self extinguishing and class-I certified as per BS 476 part 7. Material shall be CFL free combustion it should not limit HGN. No + No2 and So1 + H25 gases, smoke generated should be lighter than air and white in colour so as to allow easy exit passage in case of fire including all accessories e.g. adhesive and ....................... joint complete as per specification. All joints portion with adhesive and cotton ......
45
-
-
Providing & fixing thermal insulation in 40mm dia. Pipe (9mm thick insulation)hot water pipe line a polyolafin foam of closed cells structure having thermal conductivity of 0.036 w/M.K. at an average tempenature of 30 C°. The density of materials shall be 30 ± 5 Kg./m³ capable to operate in the range of -80° C to + 95° C fire propogation material shall be self extinguishing and class-I certified as per BS 476 part 7. Material shall be CFL free combustion it should not limit HGN. No + No2 and So1 + H25 gases, smoke generated should be lighter than air and white in colour so as to allow easy exit passage in case of fire including all accessories e.g. adhesive and ....................... joint complete as per specification. All joints portion with adhesive and cotton ......
15
-
-
Supplying, fitting & fixing C.P. 50 Ø brass grating etc. complete with civil work including white cement complete in all respects.
45
-
-
Supplying, fitting & fixing C.P. on brass Bib cock of approved make (Jaquar make continental) complete in all respects (for washing).
20
-
-
Supplying fitting & fixing as per specification drawing & direction white vitrious Jaquar make E.P.W.C. Wall Hung with chair brackets, concealed cistern, Angular Stop Cock, Health Faucet with flexible tube, wall brackets, two in one tap etc. complete in all respects. W.C.- Jaquar Aria cat no. ARS-WHT 0110.Cistern-Jaquar cat no. CIB-WHT 31801011XFD.Top Cover-Jaquar cat no. CIS-CHR 31207219.Two way bib cock- Jaquar cat no. ARI 39041.Angular stop cock- Jaquar cat no. ARI 39053.Health Faucet- Jaquar cat no. ALD 573..
10
-
-
Supplying fitting & fixing as per specification drawing & direction white vitrious Jaquar make E.P.W.C. couple closet with brass screws, Angular stop cock, Cistern fittings, Health Faucet with flexible tube two in one bib cock etc complete in all respects. W.C.- Jaquar Lyric range cat no. LYS-WHT 0309/0204.Cistern Fittings- approved make.Two way bib cock- Jaquar cat no. LYR-38041.Angular stop cock- Jaquar cat no. LYR 38053.Health Faucet- Jaquar cat no. ALD 573.Connector- Jaquar cat no. ALD 803B.
4
-
-
Supplying fitting & fixing as per specification drawing & direction white vitrious Jaquar make E.P.W.C. Wall Hung with chair brackets nut & bolts, concealed cistern, Angular Stop Cock, Health Faucet with flexible tube, wall brackets, two in one tap etc. complete in all respects. W.C.- Jaquar Fonte cat no. FNS-WHT 0112.Cistern- Jaquar cat no. CIB-WHT 31801011XFD.Top Cover-Jaquar cat no. CIS-CHR 31207219.Two way bib cock- Jaquar cat no. ARI 39041.Health Faucet- Jaquar cat no. ALD 573.
6
-
-
Supplying fitting & fixing as per specification drawing & direction white vitrious Jaquar make E.P.W.C. Wall Hung with chair brackets nut & bolts, concealed cistern, Angular Stop Cock, Health Faucet with flexible tube, wall brackets, two in one tap etc. complete in all respects. W.C.- Jaquar Vignette cat no. VGS-WHT 0118.Cistern- Jaquar cat no. CIB-WHT 31801011XFD.Top Cover-Jaquar cat no. CIS-CHR 31207219.Two way bib cock- Jaquar cat no. VGN 27041.Health Faucet- Jaquar cat no. ALD 573.
5
-
-
Supplying fitting & fixing as per specification drawing & direction white vitrious Jaquar make E.P.W.C. couple closet with brass screws, Angular stop cock, Cistern fittings, Health Faucet with flexible tube two in one bib cock etc complete in all respects. W.C.- Jaquar Vignette range cat no. VGS-WHT 0207.Cistern Fittings- approved make.Two way bib cock- Jaquar cat no. VGN 27041.Angular stop cock- Jaquar cat no. VGN 27053.Health Faucet- Jaquar cat no. ALD 573.Connector- Jaquar cat no. ALD 805B.
19
-
-
Supplying fitting & fixing as per specification, drawing & direction white vitrious floor standing Wash Basin with Basin Mixer, 2 nos Angular Stop Cock, 2 nos Connector, C.P. Waste, C.P. brass screws brackets & hook etc. complete in all respects. Basin- Jaquar Kubix cat no. KUS-WHT 0609.Basin Mixer- Jaquar cat no. KUB 35011FB.Angular Stop Cock-Jaquar cat no. KUB 35053..C.P.Waste- Jaquar cat no. ALD 709.
2
-
-
Supplying fitting & fixing as per specification, drawing & direction white vitrious wall hung Wash Basin with pedestal including Basin Mixer, 2 nos Angular Stop Cock, 2 nos Connector, C.P. Waste,basin brackets etc. complete in all respects.Basin- Jaquar cat no. ARS-WHT 0538.Basin Mixer- Jaquar cat no. ARI 39005B.Angular Stop Cock-Jaquar cat no. ARI- 39053.Connector- Jaquar cat no. ALD 801B.C.P.Waste- Jaquar cat no. ALD 709L130.Bottle trap-ACD-CHR-769L250X190
12
-
-
Supplying fitting & fixing as per specification, drawing & direction white vitrious wall hung Wash Basin with pedestal including Basin Mixer, 2 nos Angular Stop Cock, 2 nos Connector, C.P. Waste,basin brackets etc. complete in all respects. Basin- Jaquar Vignette cat no. VGS-WHT 0612.Basin Mixer- Jaquar cat no. VGN 27011B.Angular Stop Cock-Jaquar cat no. VGN 27053.C.P.Waste- Jaquar cat no. ALD 709L130.
20
-
-
Supplying fitting & fixing as per specification drawing & direction half stall standing Urinal Aquafree cat no. 60017 with cartridge etc. complete including C.P. dome shaped approved make grating complete in all respect.
URS-WHT-0702-Urinal
SNR-STL-51077-Sensor for Urinal
14
-
-
Supplying fitting & fixing as per specification drawing & direction Jaquar make Kubix range C.P. accessories with C.P. on brass screws etc. complete in all respect.
Soap Dish/Dispencer- Jaquar cat. No. AKB 35731
43
-
-
Supplying fitting & fixing as per specification drawing & direction Jaquar make Kubix range C.P. accessories with C.P. on brass screws etc. complete in all respect. Toilet Paper Holder- Jaquar cat No. AKB 35751
43
-
-
Supplying fitting & fixing as per specification drawing & direction Jaquar make Kubix range C.P. accessories with C.P. on brass screws etc. complete in all respect. Robe Hook- Jaquar cat No. AKB 35791
43
-
-
Supplying fitting & fixing as per specification drawing & direction Jaquar make Kubix range C.P. accessories with C.P. on brass screws etc. complete in all respect. Glass Shelf- Jaquar cat No. AKB 35771
25
-
-
Supplying fitting & fixing as per specification drawing & direction Jaquar make Kubix range C.P. accessories with C.P. on brass screws etc. complete in all respect.
Towel Rail- Jaquar cat No. AKB 35711
25
-
-
Supplying fitting & fixing as per specification drawing & direction Auto Hand Dryer of approved make.
HDR-WHI-MO4A-Jaquar MAKE
34
-
-
Supplying fitting & fixing as per specification drawing & direction bevelled edge mirror with wooden frame complete with masonite backing with brass screws etc. complete in all respects.
60
-
-
Supplying fitting & fixing as per specification drawing & direction single lever wall mixer with telephonic shower arrangement etc. complete in all respects. Shower Mixer- Jaquar Kubix cat no. KUB 35119.Telephone shower- Jaquar cat no. HSH 1731.Tube- Jaquar cat no. SHA 549D8.Bracket- Jaquar cat no. SHA 555.
8
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia
130
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32 mm dia
100
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 40 mm dia
70
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50 mm dia
60
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm dia
50
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia
40
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia
50
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia
50
-
-
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright Sprinkler
170
-
-
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Concealed sprinkler
170
-
-
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. - 700mm
40
-
-
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. - 1000mm
100
-
-
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. - 1200mm
15
-
-
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. - 1500mm
15
-
-
Providing and fixing carbon-di-oxide type fire extinguishers consisting of pressure tested single cast cylinder with rotary discharge valve and high pressure discharge tube of minimum 1 m length, discharge horn, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge (Halon Free Gas)
Capacity 4.5 Kg.
10
-
-
Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. (Halon Free Gas) - Capacity 6.0 Kg.
10
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group-C
300
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.
10
-
-
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
3000
-
-
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
2400
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
8000
-
-
Supplying and drawing 6 x 1.5 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required
800
-
-
Supplying and fixing of 25 mm steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
1500
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
650
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
80
-
-
Supplying & Fixing call bell suitable for single phase,230V complete as required
4
-
-
Supplying and drawing 1 run of cable of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
2500
-
-
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group-C
505
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required.
200
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
1200
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 4 sq. mm + 1 X 4 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
40
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 6 sq. mm + 1 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
60
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 10 sq. mm + 1 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
100
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 4 X 6 sq. mm + 2 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
40
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 4 X 10 sq. mm + 2 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
150
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the 4 X 16 sq. mm + 2 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
200
-
-
Supplying and fixing 8 way (4 + 24), Double door, Vertical type TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)
3
-
-
Supplying and fixing 6 way (4 + 18), Double door, Vertical type TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)
3
-
-
Supplying and fixing 40 Amps, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
9
-
-
Supplying and fixing 63 Amps, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
9
-
-
Supplying and fixing 40 Amps, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.
3
-
-
Supplying and fixing 63 Amps, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.
9
-
-
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of Single poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
126
-
-
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
10
-
-
Supplying and fixing 20 A, 240 V, SPN Industrial type socket
outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.
2
-
-
Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.
2
-
-
Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.
2
-
-
Supplying and fixing of 8 way (4 + 24), Double door surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used
where 3 phase outlets are required.)
1
-
-
ACCESS CONTROL SYSTEM
The Access Control System shall be a PC-based system based on Windows Operating Systems. Ability to store upto 1000 cardholder data and support upto 512 readers
The Access Control System shall be of modular design providing the flexibility to allow the user to add or remove any components and/or controlled functions or in the event when operating requirements change or as system expands.
The Access Control System shall support up to four (4) different Wiegand card formats simultaneously. The number of each format supported shall be unlimited.
The Access Control System shall monitor and record in a logbook all movements and activities at each control point.
It shall be a standard feature provided in the Access Control System management software for taking photos, scanning or importing cardholder images into the cardholder database. Such that stored cardholder’s image can be displayed automatically on the Access Control System.
The events log files shall include an advanced filter functions such that archive can be kept small and precise. If required, only desired information shall be archived.
The system shall contain a map viewer. This map viewer shall provide a graphical presentation of the premises or object by means of floor plans, object pictures or any desired graphical representation.
Supply, Installation, Testing and Commissioning of PC for installation of Access Software as per OEM Requirements etc. complete as required
1
-
-
Supply, Installation, Testing and Commissioning of Electro Magnetic Lock of Suitable Capacity etc. complete as required
10
-
-
Supply, Installation, Testing and Commissioning of Door Position Sensor ( DPS ) for door information feed back etc. complete as required
10
-
-
Supply, Installation, Testing and Commissioning of Exit Push Button etc. complete as required
10
-
-
Supply, Installation, Testing and Commissioning of Power Supply for Electro Magnetic Lock etc. complete as required
10
-
-
Supply, Installation, Testing and Commissioning of 6 Core x 0.2 sq mm multi strand, copper, unarmoured sheilded Cable (between the card readers & the access controllers including associated civil works etc. complete as required
800
-
-
Supply, Installation, Testing and Commissioning of 2 Core x 1.5 Sq mm, multi strand, copper, sheilded, un armoured cable( between the controller and EM Lock/ door sensor/Request to exit button and) etc. complete as required
800
-
-
Supply, Installation, Testing and Commissioning of 2 Core x 1.5 Sq mm, multi strand, copper, sheilded, twisted pair cable ( between the controller and Extension cabinet) etc. complete as required
600
-
-
Supply,Transprtation, storing at site, shifting at work place, installation, Testing and commissioning of the 2 Nos. 120 KVA UPS in parallel mode with 30 minutes battery back up with static & manual bypass Input Voltage: 3 Ph 415 Volts, ±10% Output : 3 -Phase-415Volts, 50 Hz ±2% , as per specifications and complete in all respects.The scope also includes supply, Installation, Testing and Commissioning of Sealed Maintenance Free lead acid Batteries complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries.& also TVSS at the input of each UPS to protect against transients, surges & Noise as per the tender specifications
1
-
-
Supply,Transprtation, storing at site, shifting at work place, installation, Testing and commissioning of the 2 Nos. 60 KVA UPS in parallel mode with 30 minutes battery back up with static & manual bypass Input Voltage: 3 Ph 415 Volts, ±10% Output : 3 -Phase-415Volts, 50 Hz ±2% , as per specifications and complete in all respects.The scope also includes supply, Installation, Testing and Commissioning of Sealed Maintenance Free lead acid Batteries complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries.& also TVSS at the input of each UPS to protect against transients, surges & Noise as per the tender specifications.
Supplying, installation, testing & commissioning of cubical type UPS Panel suitable for 415V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 9 tank process for powder coating in approved shade, having 630 Amp capacity extensible type TPN copper bus bars of high conductivity, DMC/SMC busbar supports, with short circuit withstand capacity of 31 MVA for 1 Sec. bottom base channel of MS section not less than 100mm x50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main busbar to switch gears with required size of copper. busbars and control wiring wtih 2.5 Sq.mm PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing following switch gears:-
1
-
-
MAIN UPS OUTGOING PANEL (Ics = Icu) (TTA PANEL IEC : 61439)
INCOMING
01 No. 630 Amp FP Moulded Case Circuit Breaker (35 KA)
01 Set of phase indicating lamps with Single Pole MCB.
01 Set of ON / OFF indicating lamps with Single Pole MCB.
01 Set of Three Phase Digital KWH including Amp, Voltage, Frequency, Power Factor and Maximum Demand Recording and inbuilt selector switch with RS 485 port & CT's etc.
BUSBAR
800 Amp FP copper busbar with coloured heat shrinkable sleeve.
OUTGOING - All Outgoint shall have Three/Single Phase Dual Source Energy Meter as per Outgoing MCB Rating with Amp, Voltage, Frequency, Power Factor and Maximum Demand Recording and inbuilt selector switch with RS 485 port & CT's etc.
3 Nos. 250 Amp FP Moulded Case Circuit Breaker (25 KA)
3 Nos. 160 Amp FP Moulded Case Circuit Breaker (25 KA)
Panel described as above
1
-
-
MAIN UPS INCOMING PANEL (Ics = Icu) (TTA PANEL IEC : 61439)
INCOMING
02 No. 250 Amp FP Moulded Case Circuit Breaker (25 KA)
02 Set of phase indicating lamps with Single Pole MCB.
02 Set of ON / OFF indicating lamps with Single Pole MCB.
02 Set of Three Phase Digital KWH including Amp, Voltage, Frequency, Power Factor and Maximum Demand Recording and inbuilt selector switch with RS 485 port & CT's etc.
BUSBAR
630 Amp FP copper busbar with coloured heat shrinkable sleeve.
OUTGOING - All Outgoint shall have ON/OFF/ TRIP Indicators with backup MCB's etc. 8 Nos. 63 Amp FP Moulded Case Circuit Breaker (25 KA)
6 Nos. 40 Amp FP Moulded Case Circuit Breaker (25 KA)
6 Nos. 63 Amp DP MCB Breaker (10 KA)
Panel described as above
1
-
-
INCOMING
02 No. 250 Amp FP Moulded Case Circuit Breaker (25 KA)
02 Set of phase indicating lamps with Single Pole MCB.
02 Set of ON / OFF indicating lamps with Single Pole MCB.
02 Set of Three Phase Digital KWH including Amp, Voltage, Frequency, Power Factor and Maximum Demand Recording and inbuilt selector switch with RS 485 port & CT's etc.
BUSBAR
630 Amp FP copper busbar with coloured heat shrinkable sleeve.
OUTGOING - All Outgoint shall have ON/OFF/ TRIP Indicators with backup MCB's etc. 6 Nos. 63 Amp FP Moulded Case Circuit Breaker (25 KA)
4 Nos. 40 Amp FP Moulded Case Circuit Breaker (25 KA)
2 Nos. 63 Amp DP MCB Breaker (10 KA)
Panel described as above
1
-
-
Supply, installation, testing & commissioning of MCCB Enclosureof MCCB/ MCCB in Sheet Steel enclosure made out of 2 mm thick CRCA sheet suitable for 3 phase 4 wire 50Hz AC system complete with four pole Moulded Case Circuit Breaker (ICS = 25KA) suitable for incoming & outgoing termination including power coating etc. complete as per specification & as required.
8
-
-
Supply, installation, testing & commissioning of 250 Amp FP MCCB/ MCCB in Sheet Steel enclosure made out of 2 mm thick CRCA sheet suitable for 3 phase 4 wire 50Hz AC system complete with four pole Moulded Case Circuit Breaker (ICS = 25KA) suitable for incoming & outgoing termination including power coating etc. complete as per specification & as required.
4
-
-
Supply, installation, testing & commissioning of 160 Amp FP MCCB/ MCCB in Sheet Steel enclosure made out of 2 mm thick CRCA sheet suitable for 3 phase 4 wire 50Hz AC system complete with four pole Moulded Case Circuit Breaker (ICS = 25KA) suitable for incoming & outgoing termination including power coating etc. complete as per specification & as required.
5
-
-
Supplying Including Fitting & Fixing, wiring of Type: Chandelier Material: Iron & Crystal
Expected Size
Fixture: 148"x63" Finish: Gold Ceiling
Jaquar Light fixtures as per direction of the department
2
-
-
Supplying Including Fitting & Fixing, wiring of Classic Cone (BDP102) Philips Light fixtures as per direction of the department
10
-
-
Supplying Including Fitting & Fixing, wiring of Classic Cone (BDP102) Philips Light fixtures as per direction of the department
20
-
-
Supply, Installation, Testing and Commissioning of Real Presence Group 700-720P, Group 700HD Codec, Eagle eye IV-12X camera, mic array, univ remote NTSC/PAL cables: 2 HDMI 1.8 m, 1 CAT 5E LAN 3.6 LAN 3.6m, 1 HDCI digital3m, Power India BIS
1
-
-
Supply, Installation, Testing and Commissioning of Partner Premier, One year real presence Group 700-720p: Group 700HDCodec,
1
-
-
Group Series & Centro Multipoint License, 6 way on Group 500 and Centro, 8 way on Group 700, either supports 4 way HD contineous presence.
1
-
-
Supply, Installation, Testing and Commissioning of Heavy Duty Motorized Projector Ceiling Lift (Make:-Liberty/ Milan/ C-Lite)
2
-
-
Supply, Installation, Testing and Commissioning of Real Presence Group 700-720P, Group 700HD Codec, Eagle eye IV-12X camera, mic array, univ remote NTSC/PAL cables: 2 HDMI 1.8 m, 1 CAT 5E LAN 3.6 LAN 3.6m, 1 HDCI digital3m, Power India BIS
2
-
-
Supply, Installation, Testing and Commissioning of Partner Premier, One year real presence Group 700-720p: Group 700HDCodec,
2
-
-
Supply, Installation, Testing and Commissioning of Group Series & Centro Multipoint License, 6 way on Group 500 and Centro, 8 way on Group 700, either supports 4 way HD contineous presence.
2
-
-
Supply, Installation, Testing and Commissioning of 98" 4K Display Panel, Screen Size (Diagonal)/ Aspect ration : 247.65 cm / 16:9, Panel Type : IPS Panel / D-LED, Effective Display Area (W x H) : 215.88 cm x 121.44 cm, Resolution (H x V):- 3840 X 2160 Pixels, Brightness:- 500 cd/m2, Viewing Angle (Horizontal / Vertical):- 178o/ 178o.
2
-
-
Supply, installation, testing and Commissioning of the following Elevators within hoist ways having dimensions as stated and WITHOUT overhead Machine room, with 415Volt A.C. variable voltage, variable frequency microprocessor based closed frequency microprocessor based closed loop control system, simplex full collective (with/without attendant) Gearless permanent magnet machine placed directly above hoist way, stainless steel car enclosure of dimensions as stated below having decorative false ceiling with light diffuser with adequate number of CFL/Fl lamps, overhead ventilation grid for optimum air flow and also providing suitable fan (at the centre of the car ceiling), flooring as per schedule and protected by centre opening sliding stainless in hair line finish for car and for only ground floor landing entrance door and by centre opening /sliding steel door finishing as per schedule for all other floors, operated by VF door operator and electronic multi-ray door protector/ detector (full length) ,electronic signal system having combined hall buttons with Dot-matrix display at all floors, touch-button car operating panel and Dot-matrix disposal battery operated alarm bell & emergency light, over load warning indicator, Fireman's switch at main lobby at ground floor, car chime, Voice synthesizer, automatic rescue device, safety against over speed and over limit travel and including minor masonry work for cutting pocket/duct in machine room or chiseling work in hoist way etc, mending good damages caused to building work and obtaining formal certificate for working the elevators after inspection of elevators by Govt. Authority (Indian Make) Elevator No 8 'Speed:-1 MPS 15 passenger lift without machine room.. (G+3 storied). Drive type:V3F Car Walls: S.S. Hair Line Finish Panels with front panels in SS Hair Line Finish. Car Flooring: S.S. Checkered Flooring. Car Door Finish: S.S. Door in hair line finish Car Push Box & Buttons: Full height COP with metallic buttons with chick lets Car Door Type: Side Opening - 2 Speed. Shaft Dimension 1850mm x 3050mm (Hospital Lift ) Car inside dimension: AS PER I.S. Car entrance : 900mm X 2100mm Travel :- Ground floor to Third floor (Four Floors). Approximately 18 Meters Stops and opening :- 5stops, 5 openings- All on the same side. Complete in all respect. '
1
-
-
FAÇADE LIGHTING
SITC of Surface/Recessed Ceiling Mounted 21W LED Downlighter Fixture. Aluminium die cast body, ADC 12, cable gland, SS Clamps, screws as required. Glare free fixture with black baffle for glare control, and honeycomb louvers for anti-glare, 3000K, 24 deg. Beam. Power Consumption Max 22W, Lumen Output 1800 Lm. Working Temperature-20°C +45°C IP Rating IP44 (not for permanent immersion) Insulation Class III. and delivers 90CRI for excellent colour rendering, and with binning-free LEDs carefully selected from two-step Macadam’s ellipse. Fitting's Smart Shield protected against polarity inversion; Protection class IP 44, safety class III. Safety clear glass. Reflector made of pure anodised aluminium. Inbuilt driver included.
150
-
-
SITC of Ground Recessed/Surface 9W LED Uplighter Fixture with Honeycomb Louver,3000K, 10°deg Beam, Stainless steel top trim, SS Finish & IK RATING 08. Lumen Output 680 Lm. Working Temperature-20°C +45°C, IP Rating IP65 (not for permanent immersion) Insulation Class III, weight upto 500gm. and delivers 90CRI for excellent colour rendering, and with binning-free LEDs carefully selected from two-step Macadam’s ellipse. PATHFINDER is Smart Shield protected against polarity inversion; an integrated super fast diode prevents accidental damage to the luminaire during installation on due to reverse polarity. Smart Shield protects against ‘hot-plugging’. Fully integrated spike-reduce on protects the constant- current driver and prevents damage to the LED die surface. With Housing Box included and LED Driver in IP65 casing box
275
-
-
SITC of Supply & fixing of Recessed / Surface Ground Mounted Fixture. 10°deg Beam, IP66, 1 Mtr Long Linear 20W LED Uplighter/ Wall washer aluminium extrusion Fixture with VISOR & Honeycomb Louver & IK RATING 06, cable gland, SS Clamps, screws as required with swivel mounting.
175
-
-
SITC of Supply & fixing of Recessed / Surface Ground Mounted Fixture, 10°deg Beam, IP65, 1 Mtr Long Linear 12W LED Uplighter/ Wall washer aluminium extrusion Fixture with VISOR & Honeycomb Louver & IK RATING 06, cable gland, SS Clamps, screws as required with swivel mounting.
128
-
-
SITC of Surface Ground Mounted 12W Small LED Projector Fixture with snoot & Honeycomb Louver, product fitted with Osram 700ma, 10°deg Beam,RGB), 80CRI, protection grade IP65 with led power driver in Color tolerance: MacAdam 4 SDCM Osram LED Mounting AR111 similar Optics PC lens. Fixture made by Aluminium die cast , SS Clamps, screws as required. Fixture Grey finish.
50
-
-
SITC of Surface Ground Mounted 12W Small LED Projector Fixture with snoot & Honeycomb Louver, product fitted with Osram 700ma, 36°deg Beam RGB), 80CRI, protection grade IP65 with led power driver in Color tolerance: MacAdam 4 SDCM Osram LED Mounting AR111 similar Optics PC lens. Fixture made by Aluminium die cast , SS Clamps, screws as required. Fixture Grey finish.
50
-
-
SITC of Surface Ground Mounted 50W Small LED Projector Fixture with snoot & Honeycomb Louver, product fitted with Osram 700ma, 48°deg Beam RGB), 80CRI, protection grade IP65 with led power driver in Color tolerance: MacAdam 4 SDCM Osram LED Mounting AR111 similar Optics PC lens. Fixture made by Aluminium die cast , SS Clamps, screws as required. Fixture Grey finish.
50
-
-
SITC of IP66 protected ALU-INSTA OUTLINE 5W/pm Flexible LED Direct View DIFFUSE 3000 WITH BACK PROFILE with integrated cable alley for cable managemnet with integrated IP rated cable connectors hidden within profile for addittional protection from weather. standard length 1000 mm. Excl. converter and end caps (on request), Made in India.
The support is made of an anodized extruded aluminum frame/ profile which makes it possible to first fix SS the wall/ceiling.
1500
-
-
SITC of IP66 protected ALU-INSTA OUTLINE 15W/pm 1000mm Long Linear LED Direct View DIFFUSE RGB WITH BACK PROFILE with integrated cablle alley for cable managemnet with integrated IP rated cable connectors hidden within profile for addittional protection from weather. converter and end caps (on request). German technology for Encapsulation, Made in India.
The support is made of an anodized extruded aluminum frame/ profile which makes it possible to first fix SS the wall/ceiling.
100
-
-
RGB CONTROLLER & AMPLIFIER
2
-
-
AUTOMATION & INSTALLATION ( Material Supply & Installation)
1
-
-
Circular Floor Recessed Adjustable Tree Uplighter
Material : Made of injected aluminium, with a cataphoresis treatment, lacquered in black colour. Exterior ring made of stainless steel AISI 304
Lens Material : Tempered glass Weight : 3.8 kg
Color Consistency : 3-step MacAdam
Fixture to be provided with inbuilt driver Cement collar to be provided to recess the fixture
50
-
-
Floor Recessed Walk Over Rated Light Fixture (Square shape)
Housing Material : V4A stainless steel. Lens Material : Single-pane, tempered safety glass tile with anti-slip coat
Note : Manufacturer to provide fully functional accessories for floor recessed application.
Electrical engineer to locate the drivers at well ventilated spaces
80
-
-
Floor Stake Mounted Adjustable Tree Uplighter
Material : Texturised anthracite lacquered aluminium injection with electro coating treatment
Lens Material : Tempered glass Weight : 3.212 Kg
Color Consistency : 3-step MacAdam
Note : Manufacturer to provide the stake accessory along with light fixture
60
-
-
Wall Recessed Step lights
Step light for outdoor applications; recessed, with frame (wall); Power consumption: 6W; Power supply: 230Vac; Delivered lumen output: 214 lm (3000K, 150°x90° asymmetrical, CRI 80,
000h L90 B10 (Ta 25°C); LED colour: 3000K;
Optics: asymmetrical 150°x90°: optic installed at an angle and set back in the chamber to to create a controlled downward light beam
Note : Manufacturer to provide backbox for wall recessed application
52
-
-
Insulated Chilled Water Piping Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.
25 mm dia. (19 mm thick insulation)
15
-
-
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.
Thickness 0.63 mm sheet
345
-
-
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.
Thickness 0.80 mm sheet
52
-
-
Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.
3.2
-
-
Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.
5.8
-
-
Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core
23.5
-
-
Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.
23.5
-
-
Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 mm thick
400
-
-
Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.
80
-
-
PROPELLER FAN (WITH GRAVITY LOUVER). Supply, installation, testing & commissioning of propeller type exhaust fans complete with mounting frame, arrangements for wall/window mounting , louvers, bird screen & accessories, complete as per specifications & drawings. The cost of wiring from the power socket outlet to the fan motor shall be included in the quoted price.Earthing shall be extended from the socket outlet to the fan motor and the cost shall be included in quoted price. Unit No.: TEPF-GF-01 to 08, TEPF-1F-09 to 11,PEPF-12 Area: Toilets & PANTRY Exhaust, CFM: 100-300
12
-
-
The Cost of All Unseen expenditure for required all existing duct & MEP Services like dimantling, lifting, shifting & installation work will be 10% extra of the total HVAC cost.
1
-
-
Main Desk Size: 2400(W)X900(D)X750(H)
Supplying , Fitting and fixing of Main Top: 2400x900. Made of 68mm thick (±1mm) combination of MDF, Particle Board and solidwood (batton construction) with top Venner face coated with clear lacquer.
Side Panel: 683X600. Made of 60mm Thick (±1mm) combination of MDF, partcile board and solidwood (baton construction) with top Veneer face coated with clear Lacquer.
Modesty Panel: 2240X600. Made of 17mm thick (±1mm). Particle Board with Veneer face, coated with clear lacquer. All thicknes edges are banded with matching liping.
ERU Size:1200(W)X440(D)X650(H) Top Panel: 1200 X 440. Made of 22mm thick (±1mm) particle board.
Side Panel : 440 X 546. Made of 17mm thick (±1mm) Particle Board.
Back Panel: 1164X546. Made of 17mm thick (±1mm) Particle Board.
Bottom Panel: 1200X440. Made of 17mm thick (±1mm) Particle Board.
Hinged Door Panel: 340X545. Made of 17mm thick (±1mm) Particle Board.
Shelf Panels: 546X404 and 344X404. Made of 16mm thick (±1mm) Particle Board. Surface Finish: Veneer Face, coated with Clear lacquer. All thickness edges are edge banded with matching lipping. Pedestal Size: 443(W)X510(D)X635(H) Top Panel: 443X510. Made of 22mm thick (±1mm) Particle Board. Side Panel: 490X 549. Made of 17mm thick (±1mm) Particle Board. Back Panel: 408X548. Made of 16mm thick (±1mm) Particle Board.
Bottom Panel: 408X473. Made of 16mm thick (±1mm) Particle Board
Drawer Front: 440X473 (Top Drawer) & 440X190(Middle & Bottom Drawers). Made of 17mm thick (±1mm) Particle Board. Surface Finish: Veneer Face, coated with clear lacquer. All thickness edges are edge banded with matching lipping. all complete as per design and direction of E.I.C.
20
-
-
Executive High Back revolving Chair Lasede
Supplying of Seat Assembly: The cushioned seat is made of injection molded Plastic outer & Inner. Plasic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m^3, and hardness load 16±2 kgf as per IS:7888 for 25% compression.
Seat Size: 47.6cm(W)X 49.2 cm(D) Back Assembly: the cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube size 1.9±0.03cmX0.16±0.0128cm. It upholstered with Pure Leaher. Back Size: 47.5cm(W)X 77cm(D) Armrests: The armrests top is moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 3.81±0.03cmX0.2±0.01cm thk M.S.E.R.W tube having chrome plated finish. The armrest Height adjustable up to 6.5±0.5cm in 5 steps.
Active Bio-Synchro Mechanism: The adjustable tilting ,mechanism is designed with the following features: * 360 degree revolving type. * Front-pivot for tilt with feet resting on ground and continous lumbar support ensuring more comfort. * Tilt - tension adjustment can be operated in seating position. * 5 position tilt limiter giving option variable tilt angle to the chair. * Seat/Back tilting ratio of 1:2 . * The mechanism housing is made up of HPDC Aluminium black powder coated.
Seat Depth Adjustment: Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm.
Adjustable Back Support: Back Frame is connected to the Up/Down mechanism housed imn Plastic T spine. It Can be adjusted in the range of 7.42±0.5cm for tghe comfortable back support to suit individual need. Pneumatic HT. Adjustment: The pneumatic height adjustment has an adjustment stroke of 10.0pneumatic 0.3cm. Pedestal Assemble: the pedestal is High Pressure Die Cast polised Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5cm. pitch-center dia(75.0±1.0cm with castors). Twin Wheel Castors: 5 nos twin wheel csors are injection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. Visitor Tubular Frame: The tubular frame is cantilever type & made of 2.54±0.03cmX0.2 ± 0.016 cm thk S.S 202 tube. the back Conneced to frame through chrome plated high pressure die cast connector pipe all complete as per design and direction of E.I.C.
20
-
-
Visitor Chair Lasede
Supplying of Seat Assembly: The cushioned seat is made of injection molded Plastic outer & Inner. Plasic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m^3, and hardness load 16±2 kgf as per IS:7888 for 25% compression. Seat Size: 60.9cm(W)X 64.7cm(D)X 92.8cm(H). Seat Height: 46.2 cm ,all complete as per design and direction of E.I.C.
40
-
-
2 seater Sofa - Pisa
Supplying of SEAT FOAM: The seat is made up of PU Foam in density 28±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32±2 kg/cu, upholstered with fabric or leatherette.
Back Foam: The back is made up of PU foam density 28±2 kg/cu.mtr with two additional top layer of supersoft foam od density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: Understructure is made up of 1.2±0.1cm thick hot pressed plywood (moisture resistance & termite proof as per IS:303) & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure fo cushioning purpose.
Leg Assembly: It is a whelled assembly made in Stainless Steel (grade SS 202) tube & plate with plastic endcap. Size: 146.0cm(W)X 90.5cm(D)X 85.8 cm (H) SH: 45.0cm ,all complete as per design and direction of E.I.C.
20
-
-
Supplying of Side Table - Edward Side Table of size 600mm(W)X 600mm(D)X450mm (H) ,all complete as per design and direction of E.I.C.
29
-
-
Supplying of Sofa Table - Victoria Coffee Table of size 1180mm(W)X600mm(D)X450mm(H) ,all complete as per design and direction of E.I.C.
21
-
-
Cupboard
Supplying of cupboard of Size: 2215(W)X 410(D) X 2000(H)
Top Panel: 2211X410. Made of 22mm thick(±1mm) Pre-laminated Particle Board.
Side Panel: 1978X390. Made of 17mm thick(±1mm) Particle Board. Back Panels: 3 nos made of 4mm thick (±1mm). Pre laminated MDF.
Bottom Panels: 3 nos made of 16mm thick(±1mm) Pre laminated particle board. Shelf Panels: 3 nos made of 22mm thick(±1mm), Pre laminated paricle board.
Partition Panels: 1978X390. Made of 16mm thick(±1mm) Pre-laminated Particle Board.
Surface Finish(Side Panels/Doors): Veneer Face, coated with Clear lacquer.
Surface Finish (All other panels): Pre-laminated.
All thickness edges are edge banded with matching lipping. ,all complete as per design and direction of E.I.C.
20
-
-
Work Table - Trident Senior Main Desk
Supplying of Work Table - Trident Senior Main Desk Overall Footprint 1804 x 750 Top thickness 25 Top Dimensions 1200 x 750 Understructure Height 725 Overall Height 750 Understructure:
- The understructure is in prelam panels, made with PLT boards.
- 2Drawer and 3Drawer storage units with different combinations to support Tops, made with 18mmPLT boards of different colours.
- Modesty and back panels, made with 18mm PLT boards.
- The Pedestals/Storages are fitted with necessary Locks PLT Board Tops (Straight Edges):
- Tops for Junior1, Junior2, and Middle desk with ERU are of 18mm thickness. - Made of 18mm thick PLT board with 2mm Edge banding. - Wenge and Savannah Maple PLT board used for making Tops. PVC membrane Tops (with profiles):
- Tops for senior main and back unit desk are of PVC membrane pressed.
- Made of 25mm thick MDFone side laminate board with 0.4mm PVC membrane pressed on to tops. - The top has Duck nose and half round profiles edges. - The top is made in only one finish: European Ash. ,all complete as per design and direction of E.I.C.
20
-
-
Elite Chair with head rest and Larger Seat Depth
Supplying of SEAT/BACK ASSEMBLY: The seat is made up of 1.2±0.1cm thk hot pressed plywood measured as per QA method described in OCP-QLTA-PL 14 -18. The back is made up of injection moulded glass filled nylon & upholstered using micro mesh fabric with high tenacity yarn with 28 density foam sandwich in lumbar area. SEAT SIZE(Larger Seat Dept): 47.0cm(W)X 51.5cm(D) HIGH RESILIENCE(HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m^3 and hardness 16±2 kgf as per IS:7888 for 25% compression.
ARMRESTS: The adjustable armrest is designed with the following features: * Up-Down adjustment - 8 steps (8.0±5 cm range) * Height adjustable armrest structure which is Powder coated & fitted with an armrest top * Fixed Armrest top is PU moulded over metal insert.
LUMBAR SUPPORT ASSEMBLY: The lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0±0.5cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: * 360 degree revolving type. * Single pivot control * Front- pivot for tilt with feet resting on ground ensuring more comfort. * Tilt tension adjustment * 4-position locking with anti-shock feature. * Seat/back tilting ratio 1:2
NECKREST: The neckrest assembly consists of polyprpylene pas with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to back assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2±0.5cm and rotation adjustment of overall 76degree±2degree. The complete neckrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass filled Nylon and fitted with 5nos twin castor wheels. The pedestal pitch-center dia is 66.1±0.5cm(7.11.9 cm castor)
COAT HANGER: The coat hanger is made up of inkection moulded filled glass nylon. The coat hanger is retrp fit and is fixed to the back assembly. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black nylon. Leatherette Quilted Upholstery for Back ,all complete as per design and direction of E.I.C.
20
-
-
Cupboard -Trident Senior Back Unit
Supplying and fixing of cupboard of Overall Footprint 1804 x 450 Top thickness 25 Top Dimensions 1200 x 450 Understructure Height 725 Overall Height 750 A) Understructure:
- The understructure is in prelam panels, made with PLT boards.
- 2Drawer and 3Drawer storage units with different combinations to support Tops, made with 18mmPLT boards of different colours.
- Modesty and back panels, made with 18mm PLT boards.
- The Pedestals/Storages are fitted with necessary Locks
B) PLT Board Tops (Straight Edges):
- Tops for Junior1, Junior2, and Middle desk with ERU are of 18mm thickness. - Made of 18mm thick PLT board with 2mm Edge banding. - Wenge and Savannah Maple PLT board used for making Tops. C) PVC membrane Tops (with profiles):
- Tops for senior main and back unit desk are of PVC membrane pressed.
- Made of 25mm thick MDFone side laminate board with 0.4mm PVC membrane pressed on to tops. -The top has Duck nose and half round profiles edges. - The top is made in only one finish: European Ash. ,all complete as per design and direction of E.I.C.
20
-
-
3 Seater Sofa Premium Lounge Chair L43
Supplying and fixing of SIDE FRAME ASSEMBLY: The side frame assembly is fitted to the two end of the connecing beam assembly to form the leg-cum armrest. It is made of 3.81±0.03cmX0.2±0.016cm thick M.S.E.R.W tube and powder coated (DFT 40-60 microns). The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy, which holds the two side frames of each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of 3.81±0.03cmX0.2±0.016cm thick M.S.E.R.W tube and powder coated (DFT 40-60 microns). The seat/back assembles are mounted on one of the tie-member which has 5.0±0.1cmX5.0±0.1cmX0.5±0.1cm. thk 5.5±0.1cm Long MS. Std angles welded to mount the seat and back. SEATREST ASSEMBLY: The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45±2 kh/m^2 wih Hardness load 25±2 kgf as per IS:7888 for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cmX(W)X 50.0(D)X6.0cm(T)
BACKREST ASSEMBLY: The backrest assembly is flexing typ and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density=45±2 kg/m^3 with hardness load 14±2 kgf as per IS: 7888 for 25% compression of the foam. The complete Moulded backrest assembly is covered with a repleaceable fabric upholstery cover. BACK SIZE: 52.0cm(W)X 59.0cm(H)X 6.0cm(T) ADJ Glides: The adj glide is injection moulded in black Nylon & Fitted to the front end of side frame assembly along with ABS moulded adj glide base to take care or unlevelled floor surface. SIZE: 164cm(W)X 70cm(D)X78.5cm(H) ,all complete as per design and direction of E.I.C.
24
-
-
Supplying , fitting & Fixing of PISA SIDE TABLE GLASS: It is 10±0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure
PISA SIDE TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade having dia 12±0.04 as per IS:1762 SIZE: 60cm(W)X60cm(D)X34.9(H) ,all complete as per design and direction of E.I.C.
34
-
-
Supplying , fitting & Fixing of PISA CENTRE TABLE GLASS: It is 10±0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure PISA CENTR TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade having dia 12±0.04 as per IS:1762 SIZE: 112cm(W)X60cm(D)X34.9(H) ,all complete as per design and direction of E.I.C.
18
-
-
1 Seater Sofa
Supplying , fitting & Fixing of SIDE FRAME ASSEMBLY: The side frame assembly is fitted to the two end of the connecing beam assembly to form the leg-cum armrest. It is made of 3.81±0.03cmX0.2±0.016cm thick M.S.E.R.W tube and powder coated (DFT 40-60 microns). The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy, which holds the two side frames of each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of 3.81±0.03cmX0.2±0.016cm thick M.S.E.R.W tube and powder coated (DFT 40-60 microns). The seat/back assembles are mounted on one of the tie-member which has 5.0±0.1cmX5.0±0.1cmX0.5±0.1cm. thk 5.5±0.1cm Long MS. Std angles welded to mount the seat and back. SEATREST ASSEMBLY: The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45±2 kh/m^2 wih Hardness load 25±2 kgf as per IS:7888 for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cmX(W)X 50.0(D)X6.0cm(T) BACKREST ASSEMBLY: The backrest assembly is flexing typ and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density=45±2 kg/m^3 with hardness load 14±2 kgf as per IS: 7888 for 25% compression of the foam. The complete Moulded backrest assembly is covered with a repleaceable fabric upholstery cover. BACK SIZE: 52.0cm(W)X 59.0cm(H)X 6.0c,m(T) ADJ Glides: The adj glide is injection moulded in black Nylon & Fitted to the front end of side frame assembly along with ABS moulded adj glide base to take care or unlevelled floor surface. SIZE: 60.5cm(W)X 70cm(D)X78.5cm(H) ,all complete as per design and direction of E.I.C.
6
-
-
Reception Table - Cignus Table of size 1650(W) x 750(D) x 750(H)
Supplying , fitting & Fixing of WORK SURFACE: Made of combination of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top and 25mm Thick
Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Softclosing access flap with in-build power box are provided on work surface for wire management. MODESTY PANEL: Made of 25mm thick MDFone side prelaminate board confirming to IS14587: 1998 with 0.4mm PVC membrane pressed on to top
UNDER-STRUCTURE: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade
confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. INTEGRATED PEDESTAL: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Drawer fronts made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism.
Handles are provided for ease of opening.
Pedestal is provided with lock for security. ,all complete as per design and direction of E.I.C.
2
-
-
Receptionist Chair- Chair Aero with large seat depth
Supplying , fitting & Fixing of SEAT/BACK ASSEMBLY: The seat is made up of 1.2±0.1cm thk hot pressed plywood measured as per QA method described in OCP-QLTA-PL 14 -18. The back is made up of injection moulded glass filled nylon & upholstered using micro mesh fabric with high tenacity yarn with 28 density foam sandwich in lumbar area. SEAT SIZE(Larger Seat Dept): 47.0cm(W)X 51.5cm(D) HIGH RESILIENCE(HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m^3 and hardness 16±2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features: * Up-Down adjustment - 8 steps (8.0±5 cm range) * Height adjustable armrest structure which is Powder coated & fitted with an armrest top * Fixed Armrest top is PU moulded over metal insert.
LUMBAR SUPPORT ASSEMBLY: The lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0±0.5cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: * 360 degree revolving type. * Single pivot control * Front- pivot for tilt with feet resting on ground ensuring more comfort. * Tilt tension adjustment * 4-position locking with anti-shock feature. * Seat/back tilting ratio 1:2
NECKREST: The neckrest assembly consists of polyprpylene pas with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to back assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2±0.5cm and rotation adjustment of overall 76degree±2degree. The complete neckrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm
PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass filled Nylon and fitted with 5nos twin castor wheels. The pedestal pitch-center dia is 66.1±0.5cm(7.11.9 cm castor COAT HANGER: The coat hanger is made up of inkection moulded filled glass nylon. The coat hanger is retrp fit and is fixed to the back assembly. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black nylon. Fabric upholstery. ,all complete as per design and direction of E.I.C.
2
-
-
Visitor's Chair Supplying , fitting & Fixing of SEAT ASSEMBLY: The seat assembly is made up of 1.2±0,1cm thick hot pressed plywood measured as per QA method described in OCP-QLRA-P14-18, upholstered with fabric upholstery covers and moulded Polyurethane foam. BACK ASSEMBLY: The back assembly is made of powder coated (DFT 40-60 microns) tubular frme of 2.54±0.03cm X 0.2± 0.016cm thk. MSERW tube designed with contoured lumber support for extra comfort. The back upholstered using Net fabric with high tenacity yarn. HIGH Resilience (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m^3 and hardness load 16±2 kgf as per IS:7888 for 25% compression. ARMRESTS: The one-piece armrests are injection moulded foam black Co-polymer Polypropylene. CENTRE_TILT MECHANISM : The mechanism is designed with the following features: * 360 degree revolving type: * 17degree±2degree maximum tilt on pivot at centre * Upright position locking * Tilt tension adjustment TUBULAR FRAME: The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of 2.54±0.03cmX0.2±0.016cm hk. MSERW Tube. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0±0.03cm. TELESCOPIC BELLOW ASSY: The bellow is 3 piece telescopic type and injection stroke of 11.0X0.3cm PEDESTAL ASSEMBLY: The pedestal assembly is injection moulded in black 33% glass-filled Nylon66 and filled with 5 nos twin wheel castors. The pedestal is 6.3±0.5cm pitch-center dia (76.3±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black nylon. SIZE: 61.0cm(W)X 64.5cm(D)X93.5cm(H) ,all complete as per design and direction of E.I.C.
8
-
-
3 seater Sofa - Pisa
Supplying , fitting & Fixing of SEAT FOAM: The seat is made up of PU Foam in density 28±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32±2 kg/cu, upholstered with fabric or leatherette.
Back Foam: The back is made up of PU foam density 28±2 kg/cu.mtr with two additional top layer of supersoft foam od density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.
Understructure: Understructure is made up of 1.2±0.1cm thick hot pressed plywood (moisture resistance & termite proof as per IS:303) & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure fo cushioning purpose. Leg Assembly: It is a whelled assembly made in Stainless Steel (grade SS 202) tube & plate with plastic endcap. Size: 206.0cm(W)X 90.5cm(D)X 85.8 cm (H) SH: 45.0cm ,all complete as per design and direction of E.I.C.
7
-
-
1 seater Sofa - Pisa
Supplying , fitting & Fixing of SEAT FOAM: The seat is made up of PU Foam in density 28±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32±2 kg/cu, upholstered with fabric or leatherette. Back Foam: The back is made up of PU foam density 28±2 kg/cu.mtr with two additional top layer of supersoft foam od density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.
Understructure: Understructure is made up of 1.2±0.1cm thick hot pressed plywood (moisture resistance & termite proof as per IS:303) & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure fo cushioning purpose. Leg Assembly: It is a whelled assembly made in Stainless Steel (grade SS 202) tube & plate with plastic endcap. Size: 86.0cm(W)X 90.5cm(D)X 85.8 cm (H) SH: 45.0cm ,all complete as per design and direction of E.I.C.
3
-
-
Beat Visitor Chair
Supplying , fitting & Fixing of The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 upholstered with knitted fabric ,over * MID BACK SIZE: 51.8 cm. (W) x 75.2 cm. (H) The HR polyurethane foam is moulded with density = 55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The tubular frame is powder coated ( DFT 40-60microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W.Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly ,all complete as per design and direction of E.I.C.
4
-
-
Leader's Work Desk
Supplying , fitting & Fixing of Primary work surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management.
Secondary Work Surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Modesty Panel: Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Under- structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security
Dimension: Primary surface 1650 mm (W) X 1650mm (D) x 750 mm (H) ,all complete as per design and direction of E.I.C.
7
-
-
Leader's Chair - Marvel High Back Chair
Supplying , fitting & Fixing of SEAT ASSEMBLY: The cushioned seat is made of injection molded Plastic outer & Inner. Plasic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45c2 kg/m^3, and hardness load 16±2 kgf as per IS:7888 for 25% compression. BACK ASSEMBLY: The cushioned back is made of PU Foam with insitu molded MS ERW Round Tube of size 1.9±0.03cmX0.16±0.0128cm. It is upholstedred with Leatherette . BACK SIZE: 47.7cm(W)76.4cm(D) ARMRESTS: The armrests top is moilded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 3.81±0.03cmX0.2±0.01cm thk MSERW tube having chrome plated finish. The armrest height adjustable up to 6.5±0.05cm in 5 steps. Active Bio-Synchro Mechanism: The adjustable tilting ,mechanism is designed with the following features: * 360 degree revolving type. * Front-pivot for tilt with feet resting on ground and continous lumbar support ensuring more comfort. * Tilt - tension adjustment can be operated in seating position. * 5 position tilt limiter giving option variable tilt angle to the chair. * Seat/Back tilting ratio of 1:2 * The mechanism housing is made up of HPDC Aluminium black powder coated.
Seat Depth Adjustment: Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm.
ADJUSTABLE BACK SUPPORT: Back Frame is connected to the Up/Dn mechanism housed in plastic T spine. It can be adjusted in the range of 7.42±0.5cm for the comfortable back support to suit individual need. PNEUMATIC Ht. ADJUSTMENT : The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3cm Pedestal Assemble: the pedestal is High Pressure Die Cast polised Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5cm. pitch-center dia(75.0±1.0cm with castors).
Twin Wheel Castors: 5 nos twin wheel csors are injection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. Visitor Tubular Frame: The tubular frame is cantilever type & made of 2.54±0.03cmX0.2 ± 0.016 cm thk S.S 202 tube. the back Conneced to frame through chrome plated high pressure die cast connector pipe
SIZE: 76.1cm(W)X76.1cm(D)X 112.7-53.1cm(H) SH:43.1-53.1cm ,all complete as per design and direction of E.I.C.
9
-
-
Visitor's Chair - Marvel Visitor Chair
Supplying , fitting & Fixing of SEAT ASSEMBLY: The cushioned seat is made of injection molded Plastic outer & Inner. Plasic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45c2 kg/m^3, and hardness load 16±2 kgf as per IS:7888 for 25% compression. BACK ASSEMBLY: The cushioned back is made of PU Foam with insitu molded MS ERW Round Tube of size 1.9±0.03cmX0.16±0.0128cm. It is upholstedred with Leatherette . BACK SIZE: 47.7cm(W)X60.1cm(D) SIZE: 60.9cm(W)X64.2cm(D)X98.3cm(H) SH:44.8cm ,all complete as per design and direction of E.I.C.
18
-
-
Cupboard
Supplying , fitting & Fixing of Cupboard of Top Panel 750 H Back Unit 1650/1800/2350 W DATE:16.09.21 Slide Door Unit Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top ,all complete as per design and direction of E.I.C.
9
-
-
Parto Plus 2 seater sofa
Supplying , fitting & Fixing of 2 Seater Sofa ,Width: 134cm , Depth: 87cm, Height: 79cm SH:43cm
STITCHING:THREAD : Poly Proplin ( type of thread : Nylon , Polyester) PITCH :- 6 ( Pitch of thread i.e. Stitch per inch) LEATHER/PVC/FABRIC: PVC
Thickness (mm) : 0.9
Weight (GSM) : 575
Moisture Content ( 10 – 12 %) : 16-20% Thickness of Plywood used(mm) : 12mm & 18mm Standard of Plywood used: {Required Standard : IS 303 Commercial Plywood} SEAT FOAM: (DENSITY, TYPE)Thickness (mm) : 69, 22 & 10 mm Density (Kg/m3): 32d Type of Foam: Vergin BACK FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm
Density (Kg/m3):28 d ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm Density (Kg/m3): 26 d BELT/ WEBBING MATERIAL: Width of belt (mm) : 68mm - 48mm
Total length of belt used (mm): 68mm :- 2500mm (2) 48mm :- 2000mm LEG MATERIAL:
* Fixing of Leg : (Self Tapping Screw / Insert with metric threading) :- Woodscrew provided on frame in addition to M-8 / T-Nut
* Material of leg : (Plastic / Insert Moulding / Wooden/ MS / SS) :- Plastic * Bush for Leg bottom : (PVC bush / Felt Pad) :- Pvc. Bush ,all complete as per design and direction of E.I.C.
12
-
-
Glaze Side Table
Supplying , fitting & Fixing of TABLE LEGS METERIALS & SIZE : OVAL METAL TUBE THICK 1.5 mm Color : SILVER POWER COATING TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE) L X W X T 600 X 600 X 8 MM Color : PARTIAL BLACK TEMERED GLASS TOP FULL BLACK TEMPERED GLASS TABLE BOTTOM MATERIALS & SIZE : (DENSITY / TYPE) L X W X T 500 X 500 X 5 MM Color : FULL BLACK TEMPERED GLASS ,all complete as per design and direction of E.I.C.
53
-
-
Glaze Coffee Table
Supplying , fitting & Fixing of TABLE LEGS METERIALS & SIZE : OVAL METAL TUBE THICK 1.5 mm Color : SILVER POWER COATING TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE) L X W X T 1100 X 600 X 8 MM Color : PARTIAL BLACK TEMERED GLASS TOP FULL BLACK TEMPERED GLASS TABLE BOTTOM MATERIALS & SIZE : (DENSITY / TYPE) L X W X T 1100 X 600 X 6 MM Color : FULL BLACK TEMPERED GLASS ,all complete as per design and direction of E.I.C.
22
-
-
Parto Plus 3 seater sofa
Supplying , fitting & Fixing of 3 Seater sofa of Width: 175cm , Depth: 87cm, Height: 79cm, SH:43cm
STITCHING:THREAD : Poly Proplin ( type of thread : Nylon , Polyester) PITCH :- 6 ( Pitch of thread i.e. Stitch per inch) LEATHER/PVC/FABRIC: PVC
Thickness (mm) : 0.9
Weight (GSM) : 575
Moisture Content ( 10 – 12 %) : 16-20% Thickness of Plywood used(mm) : 12mm & 18mm Standard of Plywood used: {Required Standard : IS 303 Commercial Plywood} SEAT FOAM: (DENSITY, TYPE)Thickness (mm) : 69, 22 & 10 mm Density (Kg/m3): 32d Type of Foam: Vergin BACK FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm
Density (Kg/m3):28 d ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm Density (Kg/m3): 26 d BELT/ WEBBING MATERIAL: Width of belt (mm) : 68mm - 48mm
Total length of belt used (mm): 68mm :- 2500mm (2) 48mm :- 2000mm LEG MATERIAL:
* Fixing of Leg : (Self Tapping Screw / Insert with metric threading) :- Woodscrew provided on frame in addition to M-8 / T-Nut
* Material of leg : (Plastic / Insert Moulding / Wooden/ MS / SS) :- Plastic * Bush for Leg bottom : (PVC bush / Felt Pad) :- Pvc. Bush ,all complete as per design and direction of E.I.C.
26
-
-
Parto Plus 1 seater sofa
Supplying , fitting & Fixing of 1 seater sofa of Width: 92cm , Depth: 87, Height: 79 SH: 43
STITCHING:THREAD : Poly Proplin ( type of thread : Nylon , Polyester) PITCH :- 6 ( Pitch of thread i.e. Stitch per inch) LEATHER/PVC/FABRIC: PVC
Thickness (mm) : 0.9
Weight (GSM) : 575
Moisture Content ( 10 – 12 %) : 16-20% Thickness of Plywood used(mm) : 12mm & 18mm Standard of Plywood used: {Required Standard : IS 303 Commercial Plywood} SEAT FOAM: (DENSITY, TYPE)Thickness (mm) : 69, 22 & 10 mm Density (Kg/m3): 32d Type of Foam: Vergin BACK FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm
Density (Kg/m3):28 d ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm Density (Kg/m3): 26 d BELT/ WEBBING MATERIAL: Width of belt (mm) : 68mm - 48mm
Total length of belt used (mm): 68mm :- 2500mm (2) 48mm :- 2000mm LEG MATERIAL:
* Fixing of Leg : (Self Tapping Screw / Insert with metric threading) :- Woodscrew provided on frame in addition to M-8 / T-Nut
* Material of leg : (Plastic / Insert Moulding / Wooden/ MS / SS) :- Plastic * Bush for Leg bottom : (PVC bush / Felt Pad) :- Pvc. Bush ,all complete as per design and direction of E.I.C.
34
-
-
Supplying , fitting & Fixing of Seat / Back Assy: The seat and back should be made up of 1.2cm.thick hot pressed plywood upholstered with leather and moulded Polyurethane foam. The back foam should be designed with Contoured lumber support for extra comfort. Back Size: 53.0cm. (W) X 95.4cm. (H) 2) Polyurethane Foam: The polyurethane foam should be moulded with density = 45+/-2kg/m3 and Hardness = 16+/-2 3) Seat-Back Connecting Spine: The seat and back should be arrested together spine made of 0.8cmthk. HR steel. The spine should be black powder-coated. 4) Armrest Assy: The armrest assy. should comprises of three parts viz. the armrest support tube and P.U. armrest and the armrest top. The armrest tube assy. is made of 2.54cm(1”) x 0.16 +/-0.01 BG. M.S. E.R.W. support tubes and Chrome plated. TheP.U. armrest is made of black integral skin polyurethane with 50-70 Shore `A’ Hardness and reinforced with M.S. Insert. The armrest top is made of ABS & upholstered with foam & leather. 5) Front Pivot Synchro Tilt Mech. features: • 360 digree Revolving type • 12 digree Seat tilt & 19 digree Back tilt • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. • Static seat depth adjustment = 5.0cm with 5 position locking. 6) Pneumatic Height Adjustment : It has an adjustment stroke of 8.0cm. 7) Bellow: The bellow is 1-piece and blow moulded in black polypropylene. 8) Pedestal Assy: The pedestal is made of die-cast aluminium with buffing finished. It is fitted with 5nos. twin wheel castors. The pedestal is 67.0cm pitch-center dia. 9) Twin Wheel Castors: The twin wheel castors are injection moulded in 30% Glass filled black Nylon. Overall Size: 770mm W x 770mm D x 1325mm – 1405mm H x 475mm – 557mm SH ,all complete as per design and direction of E.I.C.
2
-
-
Halo High Back Chair
1) Supplying , fitting & Fixing of Seat / Back Assy: The seat and back should be made up of 1.2cm.thick hot pressed plywood upholstered with leather and moulded Polyurethane foam. The back foam should be designed with Contoured lumber support for extra comfort. Back Size: 53.0cm. (W) X 95.4cm. (H) 2) Polyurethane Foam: The polyurethane foam should be moulded with density = 45+/-2kg/m3 and Hardness = 16+/-2 3) Seat-Back Connecting Spine: The seat and back should be arrested together spine made of 0.8cmthk. HR steel. The spine should be black powder-coated. 4) Armrest Assy: The armrest assy. should comprises of three parts viz. the armrest support tube and P.U. armrest and the armrest top. The armrest tube assy. is made of 2.54cm(1”) x 0.16 +/-0.01 BG. M.S. E.R.W. support tubes and Chrome plated. TheP.U. armrest is made of black integral skin polyurethane with 50-70 Shore `A’ Hardness and reinforced with M.S. Insert. The armrest top is made of ABS & upholstered with foam & leather. 5) Front Pivot Synchro Tilt Mech. features: • 360 digree Revolving type • 12 digree Seat tilt & 19 digree Back tilt • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. • Static seat depth adjustment = 5.0cm with 5 position locking. 6) Pneumatic Height Adjustment : It has an adjustment stroke of 8.0cm. 7) Bellow: The bellow is 1-piece and blow moulded in black polypropylene. 8) Pedestal Assy: The pedestal is made of die-cast aluminium with buffing finished. It is fitted with 5nos. twin wheel castors. The pedestal is 67.0cm pitch-center dia. 9) Twin Wheel Castors: The twin wheel castors are injection moulded in 30% Glass filled black Nylon. Overall Size: 770mm W x 770mm D x 1325mm – 1405mm H x 475mm – 557mm SH ,all complete as per design and direction of E.I.C.
26
-
-
3 seater sofa Mellow
Supplying , fitting & Fixing of 3 seater sofa Mellow of Dimensions: Width - 2015 mm Depth - 900 mm Height - 875 mm Mellow 3 Seater Sofa - Blue Material: Polyester fabric. Seat and back with slab stock foam of medium density and super soft foam. Plywood & Pinewood under structure with Steel S spring and Elastic belt webbing. ,all complete as per design and direction of E.I.C.
2
-
-
1 seater sofa Mellow
Supplying , fitting & Fixing of 1 seater sofa Mellow ofDimensions: Width - 1015 mm Depth - 900 mm Height - 875 mm Material: Polyester fabric. Seat and back with slab stock foam of medium density and super soft foam. Plywood & Pinewood under structure with Steel S spring and Elastic belt webbing. ,all complete as per design and direction of E.I.C.
2
-
-
Scout P 1 seater Recliner Sofa
Supplying , fitting & Fixing of 1 seater Recliner Sofa UPHOLSTERY : Material: EPU Fab Leather(Micro fiber) which has high resistance to peeling, scratches and abrasion Thickness: 1mm
Frame: Material: Slab stock foam
Density: Base 28kg/m^3 and super soft 32 kg/m^3 at top, pocket spring of diameter 2 mm is embedded in seat.
Back: The front of the backrest is made of loose conjugated polyester fibre which is weighed & filled in the upholstery to make the required cushion. Webbing: S spring of wire diameter of 3.8 mm Mechanism: Leggett & Platt make. It is made up of mild steel linkages which are riveted together. The reclining mechanism is tested for 158 kg load.
Legs: PVC bushes fitted at he bottom surface of reclining mechanism ,all complete as per design and direction of E.I.C.
2
-
-
Bloom Side Table
Supplying , fitting & Fixing of bloom side table ,MATERIALS & DIMENSION (+/- 5mm) Width 500 E B / Length 500 F C / Height 428 D / Glass thk 8 TABLE MATERIALS Glass of 8 mm thk tempered, Solid rubber woood legs and frame, MS sheet as bottom shelf DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE) PU coating to the rubber wood parts, clear glass Colour:- POWDER COATING COLOR & DFT IN MICRONS: Black DFT= 40-80 Microns ,all complete as per design and direction of E.I.C.
4
-
-
Bloom Coffee Table
Supplying , fitting & Fixing of Bloom Coffee Table MATERIALS & DIMENSION (+/- 5mm) Width: 500 Length 500 Height 428 Glass thk 8 TABLE MATERIALS Glass of 8 mm thk tempered, Solid rubber woood legs and frame, MS sheet as bottom shelf DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE) PU coating to the rubber wood parts, clear glass Colour:- POWDER COATING COLOR & DFT IN MICRONS: Black DFT= 40-80 Microns ,all complete as per design and direction of E.I.C.
2
-
-
Cupboard -
Supplying , fitting & Fixing of Cupboard with The Back Unit should be made of MDF with veneer finish and PU coating. The door should be devided in two parts, One pair of door should be made with 5mm thick glass and other pair shold be mad of MDF with veneer finish and PU coating. The size of the back unit should be 1000mm W x 480mm D x 2035mm ,all complete as per design and direction of E.I.C.
2
-
-
Encardo 1 seater Sofa Chair
* Rubber wood frame * PVC upholstery in brown shade * Soft foam * Prominent stitching lines on upholstery *Partitioned seats * Square armrest * Glossy lacquered frame in cappucino shade
SIZE: 670mm(W)X 835mm(D)X850mm(H) , SEAT HEIGHT:850 mm ,all complete as per design and direction of E.I.C.
4
-
-
Rest Room Bed
Supplying , fitting & Fixing of Bed of Overall Size : Length - 2060.0 mm
Width - 1131.0 ram Height - 945.0 mm
Material: Bed Structure consist of metal frames made of M.S. Channels in 1.0 mm Thickness. Horizontal plinths and bottom plinth are made of 25 mm Thick E1 Grade Prelaminated Particle Board. Head board is made of 18 mm thick E1 Grade Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. Tail board is made of 18 mm thick E1 Grade Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. The bed should be UL Greenguard Certified.
Side rail is made of 18 mm thick E1 Grade Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed on to it. The mattress panel of Bed are made of 18 mm thick E1 Grade Prelaminated Particle Board with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Without Storage ,all complete as per design and direction of E.I.C.
2
-
-
Supplying , fitting & Fixing of Splenda Side Table of Size L 1200 W 600 D 378 H ,all complete as per design and direction of E.I.C.
6
-
-
Work Table
Supplying , fitting & Fixing of Primary work surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management.
Modesty Panel: Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Under- structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security
Dimension: Primary surface: 1350 W x 600 D x 750 H ,all complete as per design and direction of E.I.C.
21
-
-
Work Chair-Mid Back revolving Chair Pulse with neck rest
Supplying , fitting & Fixing of The Seat is made up of 1.2±0.1 cm thk. Hot pressed plywood measured as per QA method.The Back should be made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn. Seat size shoul be: 47 cm Wx49.5cm D, Back Size: 45 cm Wx65.3 cm H. It should have High resilence polyurethane foam moulded with density=55±2kg/m3 and hardness 16±2 kgf as per IS:7888 for 25% compression. The armrest should have an Up-Down adjustment of 8.5±0.5cm which should be provided in armrest structure. Armrest Top should have an integrated layer of Thermoplasti Elastometer(TPE). The chiar should have Lumbar support assembly consisting of polypropylene pad with moulded polyurethane foam and covered with polyester fabric. The height of lumbar pad should be adjustable with an adjustment of 8±0.5cm in height.Chair should have Front Pivot Synchro Mechanism with Following Features: 360 degree revolving type,Single point Control, front-pivot for tilt with feet resting on ground for comfort, tilt Tension adjustment, 4- position locking with anti shock feature, seat/back tilting ratio of 1:2. The neck rest assembly should consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest should be fixed to back assembly through neckrest connector.Neckrest assembly should have height adjustment of 4.2±0.5cm and rotation adjustment of overall 76 degree±2 degree. The chair should have pneumatic height adjustment with an adjustment stroke of 10±0.3 cm. Pedestal assembly should be injection moulded in black 30% glass filled nylon and fitted with 5 Nos. twin wheel castors. The pedestal pitch-centre dia should be Ø66.1±0.5cm. It should also have twin wheel castors injection moulded in black nylon.Overall Size: 76.1 cm Wx76.1cmD x 114cm-128.2 cm H x 44-54 cm Seat Height. ,all complete as per design and direction of E.I.C.
12
-
-
Chair -Sedna Very High Back Chair
Supplying , fitting & Fixing of Seat smade up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. Size of back shall be (W)-46.0cm, (H)-57.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual need. Armrests should be pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated while taking back support for better adjustment of comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 113.5 to max 138.0 cms. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm. ,all complete as per design and direction of E.I.C.
5
-
-
Sedna Visitor Chair
Supplying , fitting & Fixing of Seat made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The understructure should be welded structure made up of M.S.E.R.W. ellipitical tube and the understructure should powder coated with 40-60 micron DFT (Dry film thickness) Overall dimensions of Chair shall be, Width of Chair - 51.0cm, Depth of Chair - 66.5 cm as measured from base. Height from ground - 96.0 cm. Seat height -48.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm ,all complete as per design and direction of E.I.C.
22
-
-
CM's Work Table
Supplying , fitting & Fixing of Primary work surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management.
Secondary Work Surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Modesty Panel: Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Under- structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security
Dimension: Primary surface 1800 mm (W) X 2500 mm (D) x 750 mm (H) ,all complete as per design and direction of E.I.C.
5
-
-
Cupboard
Supplying , fitting & Fixing of cupboard of Top Panel 750 H Back Unit 1650/1800/2350 W DATE:16.09.21 Slide Door Unit Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top ,all complete as per design and direction of E.I.C.
3
-
-
Work Desk
Supplying , fitting & Fixing of WORK SURFACE: Made of 25mm thick MDFone
side prelaminate board confirming to IS14587: 1998 with0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management.
MODESTY PANEL: Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top
UNDER_STRUCTURE: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. ,all complete as per design and direction of E.I.C.
9
-
-
Chair Cross Large seat depth with head rest
Supplying , fitting & Fixing of SEAT/BACK ASSEMBLY: The seat is made up of 1.2±0.1cm thk hot pressed plywood measured as per QA method described in OCP-QLTA-PL 14 -18. The back is made up of injection moulded glass filled nylon & upholstered using micro mesh fabric with high tenacity yarn with 28 density foam sandwich in lumbar area. SEAT SIZE(Larger Seat Dept): 47.0cm(W)X 51.5cm(D) HIGH RESILIENCE(HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m^3 and hardness 16±2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features: * Up-Down adjustment - 8 steps (8.0±5 cm range) * Height adjustable armrest structure which is Powder coated & fitted with an armrest top * Fixed Armrest top is PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0±0.5cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: * 360 degree revolving type. * Single pivot control * Front- pivot for tilt with feet resting on ground ensuring more comfort. * Tilt tension adjustment * 4-position locking with anti-shock feature. * Seat/back tilting ratio 1:2
NECKREST: The neckrest assembly consists of polyprpylene pas with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to back assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2±0.5cm and rotation adjustment of overall 76degree±2degree. The complete neckrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass filled Nylon and fitted with 5nos twin castor wheels. The pedestal pitch-center dia is 66.1±0.5cm(7.11.9 cm castor) COAT HANGER: The coat hanger is made up of inkection moulded filled glass nylon. The coat hanger is retrp fit and is fixed to the back assembly.
TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black nylon. ,all complete as per design and direction of E.I.C.
17
-
-
Workstation Chairs
Supplying , fitting & Fixing of SEAT/BACK ASSEMBLY: The seat is made up of 1.2±0.1cm thk hot pressed plywood measured as per QA method described in OCP-QLTA-PL 14 -18. The back is made up of injection moulded glass filled nylon & upholstered using micro mesh fabric with high tenacity yarn with 28 density foam sandwich in lumbar area. SEAT SIZE(Larger Seat Dept): 47.0cm(W)X 51.5cm(D) HIGH RESILIENCE(HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m^3 and hardness 16±2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features: * Up-Down adjustment - 8 steps (8.0±5 cm range) * Height adjustable armrest structure which is Powder coated & fitted with an armrest top * Fixed Armrest top is PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0±0.5cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: * 360 degree revolving type. * Single pivot control * Front- pivot for tilt with feet resting on ground ensuring more comfort. * Tilt tension adjustment * 4-position locking with anti-shock feature. * Seat/back tilting ratio 1:2
NECKREST: The neckrest assembly consists of polyprpylene pas with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to back assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2±0.5cm and rotation adjustment of overall 76degree±2degree. The complete neckrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass filled Nylon and fitted with 5nos twin castor wheels. The pedestal pitch-center dia is 66.1±0.5cm(7.11.9 cm castor)
COAT HANGER: The coat hanger is made up of inkection moulded filled glass nylon. The coat hanger is retrp fit and is fixed to the back assembly. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black nylon. ,all complete as per design and direction of E.I.C.
14
-
-
Conference Table Supplying , fitting & Fixing of Work Surface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade
conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Plastic ABS access flap is provided for easy access to wires and cables. Work top is
available in various shapes as shown above. Understructure: It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade
conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.
Modesty Panel: Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns).
Wire Management: An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. ,all complete as per design and direction of E.I.C.
2
-
-
Head Speaker/CM Chair
Supplying , fitting & Fixing of SEAT/BACK ASSEMBLY:The seat is made up of 1.2±0.1cm thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back is made up 1.2±0.1cm thick hot pressed plywood measured as per QA mehod described in OCP-QLTA-P14-18 and upholstered with factor or leatherette upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumbar support for comfortable seating posture. HIGH BACK SIZE: 48cm(W)X76.0cm(H)
HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane (PU) foam for seat and back is moulded with density = 45±2 kg/m^2 and hardness load 16±2kgf as per IS:7888 for 25% compression. ARMRESTS : The armrests top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 3.81 ±0.03cmX0.2±0.01 cm thk MS ERW tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps. KNEE TILT MECHANISM WITH SEAT DEPTH ADJUSTMENT MECHANISM: The mechanism is designed with the following features: * 360 degree revolving type single point control * Front pivot for tilt with feet resting on ground ensuring more comfort * Tilt tension adjusment * 4-position locking with anti-shock feature. * Seat back tilting ratio of 1:2 * Seat depth adjustment of 6.0 ±0.5cm can be locked in 6 positions FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features: * 360 degree revolving type single point control * Front pivot for tilt with feet resting on ground ensuring more comfort. * Tilt tension adjustment * 4-position locking with anti-shocking feature * Set back tilting ratio of 1:2 ADJUSTABLE BACKREST: The backrest is connected to the mechanism with a drop lift mechanism which can be adjusted in the range of 7.0±0.5cm and locked in 6 positions for the better lumbar support FIXED SPINE: The seat and back are arrested together with fixed type spine i.e no back up/dowm adjustment made of 0.8±0.05cm thk HR steel and is black powder coated (DFT 40-60 microns) PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke 10±0.3cm PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2±0.02 cm thick HR sheet , chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos twin wheel castors. The pedestal is 66.0±0.5cm. Pitch center dia (76.0±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors are injection mpoulded in black Nylon ,all complete as per design and direction of E.I.C.
2
-
-
Kareena Mid Back Conference Chair
Supplying , fitting & Fixing of SEAT/BACK ASSEMBLY:The seat is made up of 1.2±0.1cm thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back is made up 1.2±0.1cm thick hot pressed plywood measured as per QA mehod described in OCP-QLTA-P14-18 and upholstered with factor or leatherette upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumbar support for comfortable seating posture. HIGH BACK SIZE: 48cm(W)X64.5cm(H)
HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane (PU) foam for seat and back is moulded with density = 45±2 kg/m^2 and hardness load 16±2kgf as per IS:7888 for 25% compression. ARMRESTS : The armrests top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 3.81 ±0.03cmX0.2±0.01 cm thk MS ERW tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps. KNEE TILT MECHANISM WITH SEAT DEPTH ADJUSTMENT MECHANISM: The mechanism is designed with the following features: * 360 degree revolving type single point control * Front pivot for tilt with feet resting on ground ensuring more comfort * Tilt tension adjusment * 4-position locking with anti-shock feature. * Seat back tilting ratio of 1:2 * Seat depth adjustment of 6.0 ±0.5cm can be locked in 6 positions FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features: * 360 degree revolving type single point control * Front pivot for tilt with feet resting on ground ensuring more comfort. * Tilt tension adjustment * 4-position locking with anti-shocking feature * Set back tilting ratio of 1:2
ADJUSTABLE BACKREST: The backrest is connected to the mechanism with a drop lift mechanism which can be adjusted in the range of 7.0±0.5cm and locked in 6 positions for the better lumbar support
FIXED SPINE: The seat and back are arrested together with fixed type spine i.e no back up/dowm adjustment made of 0.8±0.05cm thk HR steel and is black powder coated (DFT 40-60 microns) PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke 10±0.3cm PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2±0.02 cm thick HR sheet , chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos twin wheel castors. The pedestal is 66.0±0.5cm. Pitch center dia (76.0±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors are injection mpoulded in black Nylon ,all complete as per design and direction of E.I.C.
49
-
-
3 seater Sofa Jeneiro
Supplying , fitting & Fixing of 3 seater sofa jeneiro 1. Seat : · Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 22x64mm, 34x64mm & 16x35mm without having major knots & defects on the surface. Zigzag spring of dia. 3.8mm is mounted on the seat structure using plastic spring mounting clip for support & additional cushioning purpose. Non woven fabric is stapled on the seat structure frame above the spring asly. to avoid direct contact between the metal springs and the seat foam. This prevents seat foam from tearing. Powder coated MS support pipe is fitted with the wooden seat frame to give additional strength to the structure. Complete understructure is made by gluing, nailing & stapling. · Foam: Seat is made of PU foam with density 28 kg/m3 with a top layer of supersoft PU foam with density 32 kg/m3. Recron sheet of 200GSM is wrapped & glued above this seat top foam. Seat front bottom is glued with the PU foam with density 28 kg/m3. · Upholstery: Seat upholstery is made in polyester fabric, having pockets to insert the seat foam. The fabric has a special coating which gives it a leather like feel. 2. Backrest : · Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knots & defects on the surface. 3mm MDF is stapled on the front & back of the structure. The front MDF provides a firm support for the recron back cushion to rest and the back cushion provides a surface to stick the back foam. · Foam: The back cushion is made of loose polyester fibre filled in non woven bags for each seat. Each bag is precisely weighed for achieving maximum support and comfort. · Upholstery: Backrest upholstery is made in polyester fabric, having pockets to insert the back cushion bags. The fabric has a special coating which gives it a leather like feel. 3. Armrest [LH & RH]:
· Understructure: Understructure is made of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross section 16x35mm without having major knots & defects on the surface. 2mm cardboard is stapled on the structure to provide a surface for sticking foam.
· Foam: Armrest is made of PU foam with density 28 kg/m3. The armrest cushions are made of loose polyester fibre filled in non woven bags for each side. Each bag is precisely weighed for achieving maximum support and comfort.
· Upholstery: Armrest upholstery is made in polyester fabric, having a pocket to insert the armrest cushion bag.
The fabric has a special coating which gives it a leather like feel.
4. Legs: Plastic legs with the M8 stud are fitted at the bottom surface of both the armrests and on front of the seat. 5. Assembly: Upholstered seat, backrest, armrest-LH & armrest-RH are assembled together with the M8 bolts, nuts & washer. Then a non-woven is stapled on the bottom surface to cover the structure.
6. Packet: Each packet contains one assembled sofa without legs and a separate hardware packet containing 4nos. of plastic legs.
Total Width (±10mm) : 2110
Total Height (±10mm): 890
Total Depth (±10mm) : 935
Seat Width (±10mm) : 1460
Seat Height (±10mm) : 475
Seat Depth (±10mm) : 560
Seat Back Angle (±2°) : 108 degree
Leg Height : 60 ,all complete as per design and direction of E.I.C.
6
-
-
2 seater Sofa Jeneiro
Supplying , fitting & Fixing of 2 seater sofa Seat : · Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 22x64mm, 34x64mm & 16x35mm without having major knots & defects on the surface. Zigzag spring of dia. 3.8mm is mounted on the seat structure using plastic spring mounting clip for support & additional cushioning purpose. Non woven fabric is stapled on the seat structure frame above the spring asly. to avoid direct contact between the metal springs and the seat foam. This prevents seat foam from tearing. Powder coated MS support pipe is fitted with the wooden seat frame to give additional strength to the structure. Complete understructure is made by gluing, nailing & stapling. · Foam: Seat is made of PU foam with density 28 kg/m3 with a top layer of supersoft PU foam with density 32 kg/m3. Recron sheet of 200GSM is wrapped & glued above this seat top foam. Seat front bottom is glued with the PU foam with density 28 kg/m3. · Upholstery: Seat upholstery is made in polyester fabric, having pockets to insert the seat foam. The fabric has a special coating which gives it a leather like feel. 2. Backrest : · Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knots & defects on the surface. 3mm MDF is stapled on the front & back of the structure. The front MDF provides a firm support for the recron back cushion to rest and the back cushion provides a surface to stick the back foam. · Foam: The back cushion is made of loose polyester fibre filled in non woven bags for each seat. Each bag is precisely weighed for achieving maximum support and comfort. · Upholstery: Backrest upholstery is made in polyester fabric, having pockets to insert the back cushion bags. The fabric has a special coating which gives it a leather like feel. 3. Armrest [LH & RH]:
· Understructure: Understructure is made of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross section 16x35mm without having major knots & defects on the surface. 2mm cardboard is stapled on the structure to provide a surface for sticking foam.
· Foam: Armrest is made of PU foam with density 28 kg/m3. The armrest cushions are made of loose polyester fibre filled in non woven bags for each side. Each bag is precisely weighed for achieving maximum support and comfort.
· Upholstery: Armrest upholstery is made in polyester fabric, having a pocket to insert the armrest cushion bag.
The fabric has a special coating which gives it a leather like feel.
4. Legs: Plastic legs with the M8 stud are fitted at the bottom surface of both the armrests and on front of the seat.
5. Assembly: Upholstered seat, backrest, armrest-LH & armrest-RH are assembled together with the M8 bolts, nuts & washer. Then a non-woven is stapled on the bottom surface to cover the structure. 6. Packet: Each packet contains one assembled sofa without legs and a separate hardware packet containing 4 nos. of plastic legs. Total Width (±10mm) : 1560
Total Height (±10mm) : 890
Total Depth (±10mm): 935
Seat Width (±10mm): 910
Seat Height (±10mm) : 475
Seat Depth (±10mm) : 560
Seat Back Angle (±2°) : 108 degree
Leg Height : 60 ,all complete as per design and direction of E.I.C.
4
-
-
Supplying , fitting & Fixing of Meraki Side Table of size 60cm(W)cmX60cm(D)X51.1(H) ,all complete as per design and direction of E.I.C.
12
-
-
Supplying , fitting & Fixing of Meraki Coffee Table of size 120(W)X60(D)X36,7(H) ,all complete as per design and direction of E.I.C.
8
-
-
2 seater Premium Lounge Chair L42
Supplying , fitting & Fixing of SIDE FRAME ASSEMBLY: The side frame assembly is fitted to the two end of the connecing beam assembly to form the leg-cum armrest. It is made of 3.81±0.03cmX0.2±0.016cm thick M.S.E.R.W tube and powder coated (DFT 40-60 microns). The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy, which holds the two side frames of each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of 3.81±0.03cmX0.2±0.016cm thick M.S.E.R.W tube and powder coated (DFT 40-60 microns). The seat/back assembles are mounted on one of the tie-member which has 5.0±0.1cmX5.0±0.1cmX0.5±0.1cm. thk 5.5±0.1cm Long MS. Std angles welded to mount the seat and back. SEATREST ASSEMBLY: The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45±2 kh/m^2 wih Hardness load 25±2 kgf as per IS:7888 for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cmX(W)X 50.0(D)X6.0cm(T) BACKREST ASSEMBLY: The backrest assembly is flexing typ and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density=45±2 kg/m^3 with hardness load 14±2 kgf as per IS: 7888 for 25% compression of the foam. The complete Moulded backrest assembly is covered with a repleaceable fabric upholstery cover. BACK SIZE: 52.0cm(W)X 59.0cm(H)X 6.0c,m(T) ADJ Glides: The adj glide is injection moulded in black Nylon & Fitted to the front end of side frame assembly along with ABS moulded adj glide base to take care or unlevelled floor surface. SIZE: 113cm(W)X 70cm(D)X78.5cm(H) ,all complete as per design and direction of E.I.C.
36
-
-
Mingle Unitized Conference table 10 seater in Membrane finish
Supplying , fitting & Fixing of Work Surface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above.
Understructure: It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.
Modesty Panel: Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns).
Wire Management: An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. ,all complete as per design and direction of E.I.C.
1
-
-
Secretary Table - Aristo Table 2100 and ERU 1200 with pedestal
Supplying , fitting & Fixing of Primary work surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management.
Secondary Work Surface:Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Modesty Panel: Made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top.
Under- structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.
Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDFone side prelaminate board confirming to IS14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security
Dimension: Primary surface 2100 mm (W) X 2250 mm (D) x 750 mm (H) ,all complete as per design and direction of E.I.C.
2
-
-
Grade 4 Tables
Supplying , fitting & Fixing of Godrej Model: Time Out with PU Coated 4 Seater: The Work Surfae Base material should be made of MDF board 25 mm thickness. On topPU painting of minimum 2H hardness with 75% gloss as percolour chart, colour combination on the centre and brown laminate should be there on the bottom. Understructure should made of bend pipe of MS powder coated PF dia 38 mm , 2 mm thick. Understructure should fitted to the top by SS machine screws. Plastic glides should be provided at the understructure to prevent the damage of the table topduring stacking. Overall Size: 1135 mm W x 1175 mm D x 750 mm H ,all complete as per design and direction of E.I.C.
18
-
-
Grade 4 Chairs
Supplying , fitting & Fixing of The seat and back should be made up of injection moulded high impact strength Polypropylene compound with indoor grade UV resistance. Seat size should be 52.5cm (W) x 53.2cm (D). Back size should be 51.6cm(W) x 40.5cm (H). The powder coated welded tubular frame should be made from 2.22cm dia x 0.16cm and 3.5cm x 1.5cm x 0.16cm MS ERW tube. The shoes should be made from high impact strength Polypropylene with indoor grade UV resistance and press-fitted to the frame. ,all complete as per design and direction of E.I.C.
72
-
-
Billing Counter
Supplying , fitting & Fixing of Table: Godrej Model: Enterprise 1500 w/o CPU Hanger Overall Size: 1500 mm W x 750 mm D x750 mm H . Worktop:18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Modesty panel:18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Rectangular Frame: Fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester.Plastic Cap for Cable
travel: Injection Moulded Polypropylene. Darwer: Shell and Drawer tray :0.6mm thick CRCA (IS:513) , Finish: Powder
coat (Epoxy polyester) ,all complete as per design and direction of E.I.C.
1
-
-
Serving Counter
Supplying , fitting & Fixing of Worktop The top is in Stainless Steel brushed finish with PLB insert for durability. Easy to clean and maintain hygiene. Understructur e Side Frames Made from 30mm x 30mm x 1.5mm thick M.S Powder coated tubes at base which are welded and are fixed to top with screws. The bottom ends are closed with Plastic buffers. MS Shade : S/G Mettalic Dark Grey (Nerocoat - 9000626) Cross Member Made from 30mm x 30mm x 1.5mm thick M.S Powder coated tube, which is welded and bolted to side frames. ,all complete as per design and direction of E.I.C.
1
-
-
Supplying , fitting & Fixing of Grande Pro Dining table 4 seater of size 117cm(W)X 75cm(D)X77cm(H) ,all complete as per design and direction of E.I.C.
26
-
-
Supplying , fitting & Fixing of Grande Pro Dining Chair of size 45cm(W)X45(D)X95cm(H) ,all complete as per design and direction of E.I.C.
104
-
-
Buffet Counter
Supplying , fitting & Fixing of Material: Glass and Rubber wood with MDF body Table Top: Tempered Glass Table Top Thickness: 12mm thick Table Top Seating: 6 SIZE OF TABLE: 1400mm(W)x450mm(D)x750mm(H) Drawer size: 420mm(W)x 305mm(D) ,all complete as per design and direction of E.I.C.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements