North Eastern Regional Institute Of Water And Land Management Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 40,000Document Cost
₹ 1,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_NERIW_654250_1Bid Award Id
ViewTender No
NRWM/RF/19/2021-22/4329Tender Authority
North Eastern Regional Institute Of Water And Land Management ViewPurchaser Address
-Website
http://http://neriwalm.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
76 mm OD, 2mm thick
-
-
-
Bottom & top cord 60 mm OD, 2 mm thick
-
-
-
48 mm OD, 2mm thick
-
-
-
42 mm OD, 2mm thick
-
-
-
33/25 mm, 2 mm thick
-
-
-
Insert GI pipes of minimum 60 mm OD or more to have foundation depth of 75 cm or more depending upon soil type and prevailing wind condition, grouted with cement concrete mixture of 1:2:4 using telescopic insertion of column.
-
-
-
All nuts & bolts must be of high tensile strength and galvanized.
-
-
-
One entrance room of size 3m x 3m x 3m (L x W x H) need to be provided and covered with 200-micron UV stabilized transparent plastic film. Two hinge doors of size 2m width & 2.5 m height double leaf made in plastic/FRP sheets mounted in suitable strong frame.
-
-
-
Buffer entry of size 5 ft x 5 ft x 8 ft covered with UV stabilized 200-micron poly film.
-
-
-
*All the control system, switching unit etc inside the room with pacca flooring of the Buffer room.
-
-
-
Rust free working bench in the house. Size of the bench is 1 mtr x 18 mtr
1
-
-
UV stabilized 200-micron transparent Plastics films conforming Indian Standards (IS 15827; 2009), multi-layered, anti-drip, anti-fog, anti-sulphur, diffused, clear and having minimum 85 % level of light transmittance.
1
-
-
All ends/joints of plastic film need to be fixed with two-way aluminium profiles with suitable locking arrangement along with curtain top. Wooden batons or PVC grippers need to be used.
-
-
-
Zigzag high carbon steel with spring action wire of 2-3 mm diameter must be inserted to fix shade net into Aluminum profile.
-
-
-
Co axial fan (ISI mark) of minimum 1200 mm diameter containing 6 numbers of GI sheet blades, frame is of GI sheet materials followed by aluminum louver.
1
-
-
Cellulose pad of thickness 4 inch -6 inch thick, height : 5 inch, width as desired equipped with anodized Aluminum frame. Cooling pad complete with all necessary framing material (aluminum) as required for distribution and return, gutter, down spout cap and return, gutter down spout cap and drip pan, plumbing kit, pump 220 Volt single phase, 50 cycle, drilled PVC piping cap, pad retainer, all suspension hardware, metal flashing required to seal pad for vent opening over flow 20mm PVC & 40 mm standard sink drain.
-
-
-
Circular pump with required capacity & accessories to be provided for wetting & circulating the pad area.
-
-
-
The necessary digital controller with sensory device & accessories of standard quality (at least two units for 500 sqm area) should be provided to operate the fan & pad system to control temperature & humidity inside the Greenhouse.
-
-
-
The proposed chamber will be equipped with humidifier ( as desired up to 80 %) or de humidification fan.
-
-
-
Electrical items such as pump. Lighting voltmeter, amp-meter etc will have electrical panel (push Button) which comply with CPRI guideline.
-
-
-
The complete proposed facility with a programmable control system (PLC) should be equipped with the following facility:
-
-
-
* Programmable photoperiodic timer.
-
-
-
Use copper wire to withstand desired load of required electrical gadgets/appliances with ISI mark.
-
-
-
UV stabilized 50% shading net with motor/manually operated mechanism for expanding and retracting. Size of net should be equal to the floor area of green house.
1
-
-
Drip irrigation System under green house need to be selected on the basis of crop spacing(design on spacing 45 cm x 45 cm) along with gogging and misting facilities. The spacing considered for calculation. The suggested bill of materials are Sand Filter 5 Cum/hr, Screen Filter 10 Cum/hr, Control Valve 63 mm, Control Valve 50 mm, By-pass Assembly 1.5 Inch, Air Release Valve 1.00 inch, Non-Retuirn Valve 1.5 inch,Throttle Valve 1.5 inch, Flush Valve 50 mm , Venturi 1.5 inch Assembly with manifold , PVC pipe 63 mm/6 kg/Square cm, PVC pipe 50 mm /6kg/Sqcm, PE plane lateral 16 mm , Emitting pipe lateral 16 mm @ 0.45 m spacing , hanging type micro sprinkler nozzle (four way take off assembly) for very fine water particles(foggers & mister) to be fixed in PE pipe of diameter 16 mm, Water Tank capacity 2000 Liters and fittings & accessories
1
-
-
1 m wide and 10 cm thick footpaths should be provided in the centre (length x width ) & made of cement concrete ration of 1:2:4.
1
-
-
22 cm brick wall of 1m height (24 cm below and 80 cm above ground level on all the four sides. The wall needs to be plastered and water proofing cement with 1:6 ratio.
1
-
-
Roll up UV stabilized 200-micron transparent plastic film as curtains need to be provided up to 3.0 m height on all sides having automatic type motor operated crack mechanism. However, provision for manual opening and closing of curtains need also be provided. 40 mesh nylon insect proof nets (UV stabilized) of equivalent size need to be fixed inside the curtains. Anti-flapping strips is suggested to ensure smooth functioning of the curtain.
1
-
-
Total(Including GST, all other charges, etc) :
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements