Municipal Corporation Tender

Providing and fixing Caution/Warning sign of 900mm Triangular (Type-Xl) equilateral triangle madeout of Retro reflective sheeting of Type-XI of ASTM D4956-09 High intensity Prismatic Retro reflective sheeting and conforming to IRC 67:2012 for full background of White colour and letters/logos done by screen printing in Black colour ,borders by screen printing in Red colour and fixed over 4mm Alluminium composite material sheet having 05mm thick Alluminium skin on both sides with black side painted grey colour and fixed over back support frame of MS angle 25x25x3mm all round and fixing 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2. lm from the ground level the bottom of the road.The signpost should be painted with one coat ofrd oxide paint and 2 coats of 1st quality synthetic enamil paint Black & whit colour with bands of 30cm height.The signpost shall be firmly fixes with MS base angle 35x35x4 mm in to the ground by M15 concrete foundation of size 450x450x600 mm or by fixing to hand rails with necessary or by fixing to hand rails with necessary clamps (3nos) with permananent welding etc including cost and conveyance of all materials equipment,machinery and labour with all leads and lifts , loading and unloading charges necessary for satisfactory completion of the work as directed by the Engineer-in -charge

Supply and fixing of Molded Shanks raised Pavement Markers made of polycarbonate and ABS molded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000Kg tested in accordance to ASTM D 4280 type H and complying to specifications of Category A of MORTH circular no RW/ NH- 33023/10-97 - Do III, Dt.11-06-1997. The height, width and length shall not exceed 50mm, 100mm and 100mm with minimum reflective area of 13 Sqm on each side and the slope to the base shall be 35+/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19+/- 2mm and height not less than 30+/- 2mm) from the body is to be a minimum value of 700Kgs. Fixing will be by drilling holes on the road for the twin shanks to go inside without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete and as directed by the Engineer-in-Charge.

Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorsing glass beads @ 250gms with reflectorising glass beads on bituminous surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC:35, the material should be of BERGER company /BERGER equivalent and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consingment of the said material and will compell the vendor has to repalce the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department) b) Luminance factor of the material should be in the range of 80-85% at 45degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, part-1 1989 and should pass at the range of '0' degree centigrade to '-10' degree centigrade D) Adhesion: Strong E) Softening point:102 degree centrigrade F) Dried film finish: Smooth and uniform G) Night vision: High as directed by the Engineer-in-Charge and confirming to IS:164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997